1. Introduction
Congratulations on your purchase of the CPVAN PIR CP2 Motion Sensor Alarm. This device is designed to detect human movement, making it ideal for monitoring entry into your shop or home. Utilizing fuzzy logic processing technology and intelligent analysis algorithms, it accurately interprets signals to provide reliable security.
Depending on your needs, the alarm can sound a loud siren or a friendly chime. It can be operated directly on the unit or via a remote control. For advanced security, you can link multiple remote controls and integrate additional CPVAN Home Alarm System sensors like door/window sensors or other PIR sensors.
IMPORTANT: For further information and technical assistance, please refer to www.cpvans.com. We continuously improve our site to ensure the best possible experience. We typically respond to questions within 24 hours.
Image: CPVAN CP2 PIR Motion Sensor Alarm unit and its remote control.
2. Box Contents
Please check that all items are present in the package:
- 1 x CP2 PIR motion sensor alarm
- 1 x remote control
- 3 x batteries 1.5V AA (alkaline)
- Flexible mount
- Pair of screws
- Instructions for use (this manual)
3. Product Overview
The CP2 PIR Motion Sensor Alarm features a compact design with clearly labeled components for easy operation.
Image: Detailed diagram of the CPVAN CP2 PIR Motion Sensor Alarm and its remote control, highlighting key features.
3.1. CP2 PIR Motion Sensor Alarm Unit
- Siren (125dB): The main alarm sound output.
- Detection Window: The area where infrared motion is detected.
- Mode Button: Used to switch between different sound modes (siren/chime).
- On/Off Button: Powers the unit on or off.
- Pairing Button: Used for pairing with remote controls and additional sensors.
- Volume/Pairing Button: (Also labeled as 'Volume' and 'Pairing' on the top of the unit in the diagram)
- DC5V Port: For external power supply.
- Child Safety Screw: Secures the battery compartment.
3.2. Remote Control
- Arm Button: Activates the alarm unit.
- Disarm Button: Deactivates the alarm unit.
- SOS Button: Triggers a loud emergency alarm.
- Switch Voice / Adjust Volume Button: Switches between Chime and Siren, and adjusts volume.
4. Setup
4.1. First Preparation (Battery Installation & Factory Reset)
- Slide off the back lid of the PIR motion sensor alarm.
- Insert the 3 AA batteries (included).
- Close the lid.
- To perform a factory reset (recommended for initial setup or if issues arise):
- Ensure the device is switched ON.
- Remove one or all batteries from the PIR unit.
- Long-press the MUSIC button (right side button on the top of the unit).
- While still holding the MUSIC button, re-install the battery.
- Continue holding the MUSIC button until you hear 10 beeps followed by 5 rapid beeps.
- Release the MUSIC button. The factory reset is now complete. Your PIR motion sensor alarm will reset and resume in Armed mode.
Video: Demonstrates the factory reset process and pairing multiple remote controls.
4.2. Pairing Remote Controls
Your PIR motion sensor alarm is pre-paired with the supplied remote control. To pair additional remotes:
- Ensure the PIR motion sensor alarm is ON.
- On the PIR motion sensor alarm unit, long-press the Pairing button (left side button on the top of the unit) to enter pairing mode. The detector light will light up continuously (red).
- Press any button on your remote control. You will hear two beeps to indicate correct pairing.
- Short-press the Pairing button on the PIR unit to exit pairing mode. Your remote has now been paired.
Multiple remotes can be connected to any PIR motion sensor. Each PIR motion sensor alarm can be paired with 5 or more remote controls, and each remote control can manage multiple PIR motion sensors simultaneously.
4.3. Pairing with CPVAN Alarm System Sensors
You can extend your PIR motion sensor alarm with additional CPVAN Home Alarm System sensors (e.g., window & door sensors, other PIR motion sensors). Triggering any paired sensor will cause your PIR motion sensor alarm to sound a Siren or a Chime.
To add sensors, follow this procedure:
- Enter Pairing Mode: Long-press the Pairing button on the PIR unit. The detector light will light up continuously.
- For normal sensors: Use the Pairing button.
- For emergency sensors: Use the Mode button. Emergency sensors are always active and trigger an alarm even if the CP2 PIR motion sensor alarm is disarmed.
- Activate Your Sensor:
- For a door & window sensor: Separate the magnet from the main sensor unit.
- For a PIR sensor: Wave your hand in front of its detection window.
- You will hear two beeps, indicating successful pairing.
- Exit Pairing Mode: Short-press the Pairing button (or Mode button if pairing an emergency sensor) on the PIR unit.
IMPORTANT: If you have added emergency sensors, these can only be deleted from the device by performing a factory reset. Refer to the corresponding instructions in this manual.
5. Operating Instructions
5.1. Switching the Unit ON/OFF
- To Switch ON: Long-press the On/Off button (middle button on the top of the unit). You will hear one short beep, and the red detection light on the front will light up once. The unit is now on. Factory settings default to armed mode upon startup.
- To Switch OFF: Long-press the On/Off button. You will hear one long beep, and the red detection light on the front will light up once.
IMPORTANT: Switching the unit On/Off and arming it are separate steps. The unit has a memory function and will resume in its last setting (armed or disarmed) after being switched off and on again.
5.2. Arming and Disarming
- Arming:
- Short-press the On/Off button on the alarm unit. You will hear one beep, and the detector light will light up once.
- Alternatively, press the Arm button on the remote control.
- Disarming:
- Short-press the On/Off button on the alarm unit. You will hear two beeps, and the detector light will light up twice.
- Alternatively, press the Disarm button on the remote control.
5.3. Changing the Sound (Siren or Chime)
Short-press the Mode button (right side button on the top of the unit) to cycle between sounds. Each press will play a short sample of the selected sound (Siren or Chime).
5.4. Adjusting Volume
Short-press the Volume button (left side button on the top of the unit) to adjust the volume. There are two volume levels.
5.5. Stopping the Siren Alarm Sound
There are three ways to stop the siren alarm sound:
- Short-press the Mode button or the Pairing button on the alarm unit. The sound will stop, and the unit will remain armed.
- Short-press the On/Off button on the alarm unit. The alarm sound will stop, and the PIR motion sensor alarm will be disarmed. Short-press the On/Off button again to re-arm it.
- Press the Arm or Disarm button on the remote control.
- Pressing the Arm button stops the alarm, and the unit stays armed.
- Pressing the Disarm button stops the alarm, and the unit changes to disarmed mode.
5.6. Three-Second Delay Arming Function
After you arm the unit with the remote control, it will not be triggered immediately. The detector light will light up three times, and then the unit enters arming status. This provides you with three seconds to leave the alarm area without triggering it.
6. Maintenance
6.1. Changing Batteries
IMPORTANT: When the batteries are running low, the detector light will flash once every 40 seconds, and a beeping sound will be heard. Please replace the batteries promptly.
PIR Motion Sensor Alarm Unit:
Slide off the back panel and replace the 3x AA size 1.5V Alkaline batteries.
Remote Control:
Remove the screw on the back of the remote control. Remove the back panel and replace the battery. The battery type is CR2025 (3V, Lithium battery).
7. Troubleshooting (Frequently Asked Questions)
Q: The PIR motion sensor alarm is switched on but does not detect any motion.
A: The system might not be armed. Short-press the On/Off button to arm the device. The device remembers its last setting; if it was disarmed when switched off, it will be in disarmed mode when switched on again. Briefly pressing the On/Off button will arm the device again.
Q: The PIR does not enter pairing mode when pressing the Pairing or Mode button.
A: The device might be switched off. Long-press the On/Off button to switch the unit on. Then, enter pairing mode by long-pressing the Pairing or Mode button.
Q: The device does not switch on.
A: Check the batteries. They might be empty.
Q: The device signals motion when there is no motion ("false alarms").
A1: The PIR motion sensor alarm is activated by infrared light and can also be triggered by direct sunlight. It is advised to keep the device out of direct sunlight.
A2: Animals like dogs, birds, and cats are known to trigger PIR motion sensors as well.
Q: The remote-control indicator light is on when I press a button, but the PIR motion detector does not react to it.
A1: The signal might not penetrate walls or cover large distances.
A2: Try opening the remote control and taking the battery out and back in again.
A3: The battery is running out of power. Insert a new battery.
Q: I have connected a Door & Window sensor, and I cannot change the alarm sound from siren to chime.
A: If you installed your Door & Window sensor in Emergency mode, the siren sound is the only option. It cannot be changed unless you delete the sensor and reconnect it in normal mode (using the Pairing button).
8. Technical Specifications
| Feature | Specification |
|---|---|
| Power | DC 5V / 3x AA Batteries |
| Current | <300uA |
| Work Current | <100mA |
| Switch off Current | <40uA |
| Detection Distance | <8m |
| Alarm Sound | 125dB |
| Detection Angle | 110 degrees |
| Working Humidity | <80% |
8.1. Detection Range Profile
IMPORTANT: The Infrared detector is sensitive to a human's vertical movement and less sensitive to horizontal movements. For optimal performance, aim the device at a 90-degree angle to a person's walking direction.
The PIR motion sensor alarm detects signals at a distance of up to 8 meters, with a 110-degree detection angle. The detection profile is typically wider horizontally closer to the sensor and narrows vertically, with an effective range up to 8 meters and a height of approximately 2 meters at maximum range.
9. User Tips
- The alarm is very loud (125dB), so consider placement carefully to avoid startling occupants unnecessarily.
- The setup process is generally straightforward. Follow the battery installation and pairing steps closely.
- The product is typically sold as a bundle including one main unit (host) and one remote control.
10. Support
For any questions or issues not covered in this manual, please contact CPVAN support:
- Website: Visit www.cpvans.com for more information and instructional videos.
- Email Support:
- For US customers: support@cpvans.com
- For UK customers: info@cpvans.com
- For DE customers: support2@cpvans.com
- For other countries: Amazon@cpvans.com
- Telephone: +86 (0755) 2308-7066 (during office hours)
- Address: Floor 3, Yifenghua Mansion, Huaning Rd, Dalang Subdistrict, Longhua District Shenzhen, Guangdong, CN.
You can also find CPVAN products, including additional sensors, on the Amazon CPVAN Storefront or at www.cpvans.com.
A PDF version of this user manual is available for download: User Manual (PDF)