TELESIN GP-WBT-001

Contents

TELESIN Diving Underwater Selfie Stick with Wireless Remote Control

Model: GP-WBT-001

TELESIN Diving Underwater Selfie Stick with GoPro camera attached, showing extended and compact views.

Product overview: TELESIN Diving Underwater Selfie Stick with remote control.

1. Introduction

Thank you for purchasing a TELESIN product. Please read this user manual carefully before use to ensure proper operation and to maximize the lifespan of your device.

2. Important Safety Notes and Warnings

  • Always keep this user manual properly. When handing over the product to others, ensure to include this user manual.
  • Pay attention to all warnings and follow all instructions in this user manual.
  • After using the product in a seawater environment:
    1. First, shake off any seawater from inside the selfie stick.
    2. Then soak it in fresh water for 10 minutes.
    3. After removing the product from fresh water, rinse it under gentle running tap water for 5 minutes.
    4. After washing, wipe away any water droplets remaining on the surface with a soft, dry cloth and leave to air dry. Do not dry with a hair dryer or any other heat source.
    5. Store the product in a dry, well-ventilated location.
  • Do not disassemble or damage this product. If it becomes deformed or damaged, stop using it immediately.
  • Do not cover the product with items like towels or clothes during charging to prevent fire hazards.
  • Do not drop the product or use it under high temperatures or short-circuit conditions.
  • Keep this product out of reach of children.
  • The product has passed the waterproof test of GB/T 4208-2017 and IEC 60529-2013 enclosure protection rating standard IP68. It is not recommended to use the product in extreme water environments or unknown liquid environments. Do not use it in hot springs or corrosive liquids.
  • This product is only compatible with GoPro HERO 13, 12, 11, 10, 9, and 8 models.
  • The waterproof depth of this product is 30 meters.

Warnings

Do not disassemble the product or replace the battery. If you suspect any problem with the product, contact the purchase platform for after-sales service.

Diver using the selfie stick underwater, illustrating 30m waterproofing.

Deep waterproofing allows exploration without limits, up to 30 meters.

Selfie stick undergoing various quality tests: waterproof, drop, remote control, and 48-hour salt spray test.

The product has undergone multiple authoritative tests for excellent quality.

3. Package Contents

Please check the box for the following items:

  • 1 x Box
  • 1 x Underwater Bluetooth Selfie Stick
  • 1 x Locking Screw
  • 1 x Charging Cable
  • 1 x Anti-Lost Wrist Strap
  • 1 x User Manual
Diagram showing all items included in the package: box, selfie stick, locking screw, charging cable, wrist strap, and user manual.

All components included in the TELESIN selfie stick package.

4. Setup: Installation and Connection

  1. Mount the Action Camera: Attach your GoPro HERO camera onto the selfie stick. If diving deeper than 10 meters, use a waterproof case (not included in the package).
  2. Open Camera Remote Connection: On your action camera, navigate to the remote connection interface and select "Connect with the remote". (The interface may vary by camera model; refer to your camera's user manual).
  3. Power On Selfie Stick: Press and hold the power button (⏻) on the selfie stick for 3 seconds to turn it on. It will automatically begin searching for signals.
  4. Bluetooth Pairing: Before the Bluetooth connection is established, all three indicator lights on the selfie stick will light up and flash simultaneously. Once successfully connected, the indicator light of the corresponding mode will light up. Complete the connection within 2 minutes, or the remote will automatically shut down.
Diagram illustrating how to mount the GoPro camera, connect via Bluetooth, and power on the selfie stick.

Step-by-step guide for mounting your camera and establishing a Bluetooth connection.

5. Operating Instructions

Controls Overview

Close-up of the selfie stick's remote control showing the Power Button, Shutter Button, Mode Button, and Shooting Mode indicator.

Remote control buttons and their functions.

  • Power Button (⏻): Turns the selfie stick and connected camera on/off.
  • Shutter Button (◎): Starts and stops recording or takes photos.
  • Mode Button (M): Switches between different shooting modes.
  • Shooting Mode Indicator: Shows the currently selected camera mode (Time-lapse, Video, Photo).

Functions

  1. Switch Shooting Mode: Press the Mode button (M) to cycle between camera time-lapse (◷), video (▶), or photo (◎) mode. The status light corresponding to the selected mode will illuminate.
  2. Start/Stop Shooting: Press the Shutter button (◎) to start recording or take a photo. Press the Shutter button (◎) again to stop recording.
  3. Remote On/Off: Each time you press and hold the Power button (⏻), you can remotely turn the connected camera on or off synchronously.
  4. Reset Pairing: Press and hold the Mode button (M) for 3 seconds to reset the Bluetooth pairing.

6. Charging

To charge your selfie stick, use the included charging cable. Connect the contact end of the cable to the charging port on the left side of the selfie stick, and connect the other end of the charging cable to a USB power source (e.g., computer USB port, USB wall adapter).

  • Charging Time: Approximately 1 hour
  • Battery Capacity: 80 mAh
  • Input: Pogo Pin Connector

Note: Data measured by TELESIN laboratory; slight deviations may occur due to changes in objective conditions.

Diagram showing the correct and incorrect way to connect the charging cable to the selfie stick's charging port.

Ensure correct orientation when connecting the charging cable.

7. Indicator Light Guide

Connection Status Indicators

Connection StatusLamp Display StatusMeaning
Bluetooth connection beforeThree lights will remain on and flash together● ● ● (Flashing)
Bluetooth connection establishedIndicator light will remain on (corresponding to mode)○ ● ○ (Solid)
During shootingIndicator light will flash (corresponding to mode)○ ● ○ (Flashing)

Battery Level Indicators

Electric Charge StateLamp Display StatusMeaning
Current battery level below 33% (Charge promptly)One light flashing● ○ ○ (Flashing)
Current battery level below 66%Two lights flashing● ● ○ (Flashing)
Current battery level below 99%Two lights flashing● ● ○ (Flashing)
When fully chargedThree lights will remain on● ● ● (Solid)
At the lowest battery level (Charge promptly)The indicator light will begin flashing slowly from the leftmost light● ○ ○ (Slow Flashing)

8. Maintenance

Proper maintenance ensures the longevity and optimal performance of your TELESIN Diving Underwater Selfie Stick.

  • After Seawater Use: Follow the detailed instructions in Section 2. Important Safety Notes. This includes shaking off seawater, soaking in fresh water, rinsing, wiping dry, and air drying. This is crucial to prevent corrosion and maintain waterproofing.
  • General Cleaning: Wipe the selfie stick with a soft, dry cloth after each use to remove any dirt, dust, or moisture.
  • Storage: Store the product in a dry, well-ventilated place away from direct sunlight, high temperatures, and corrosive liquids.
  • Avoid Impact: Do not drop the product or subject it to strong impacts, as this can damage internal components or compromise its waterproof integrity.

9. Troubleshooting

  • Bluetooth Not Connecting / Stops Working After Immersion:
    Ensure the selfie stick is thoroughly dried after each water use, especially after seawater exposure (refer to Maintenance section). Water ingress can cause Bluetooth or charging issues. Try resetting the pairing (Section 5). If the issue persists, contact customer support.
  • Device Not Charging / Not Turning On:
    Ensure the charging cable is correctly connected (refer to Section 6) and try a different USB power source. Check for any visible damage to the charging port or cable. If the device remains unresponsive, contact customer support.
  • Inability to Switch Modes on Camera via Selfie Stick:
    While the selfie stick is designed to switch modes, some specific GoPro models or firmware versions might have limitations. Ensure your GoPro's firmware is up to date. If the issue persists, you may need to change modes directly on your camera.
  • Compatibility Issues with Other Camera Brands (e.g., DJI Osmo, Insta360):
    This selfie stick is specifically designed for GoPro HERO 13/12/11/10/9/8 models and may not be compatible with other action cameras.
  • Lost Charging Cable:
    Contact TELESIN customer support or the seller to inquire about purchasing a replacement charging cable.

10. Specifications

FeatureDetail
BrandTELESIN
Model NumberGP-WBT-001
MaterialAluminum
TypeSkeletons & Frames
Compatible Action Camera BrandGoPro (HERO 13/12/11/10/9/8)
Waterproof Depth30 meters
Waterproof RatingIP68 (GB/T 4208-2017 and IEC 60529-2013)
Pole Length (Collapsed)25 cm
Pole Length (Extended)85 cm
Battery Capacity80 mAh
Charging Time1 hour
OriginMainland China
Package Length29 cm
Package Width12 cm
Package Height8 cm
Package Weight0.419 kg
Diagram showing the selfie stick extended to 85cm and collapsed to 25cm.

Extend the pole for a wider view, from 25cm to 85cm.

Images of GoPro Hero 8, 9, 10, 11, 12 indicating compatibility.

Compatible with GoPro Hero 8, 9, 10, 11, and 12 models.

11. User Tips

  • Size Expectation: Some users note the product is larger than expected. Be aware of its dimensions (25cm collapsed, 85cm extended) for portability.
  • Build Quality: The selfie stick is generally regarded as solid and well-made, with good manufacturing materials.
  • GoPro Compatibility: It connects perfectly with GoPro Hero 12 Black and other specified models. Ensure your camera's Bluetooth is enabled and discoverable during pairing.
  • Post-Dive Care: Always follow the detailed cleaning instructions after using in water, especially saltwater, to prevent issues like Bluetooth malfunction or charging problems.

12. Warranty and Support

Disclaimer

Please read this statement carefully. By using this product, you acknowledge and accept it in full. Always check the product carefully before each use and do not use it if damaged or deformed. By using this product, you acknowledge and agree that you are fully responsible for your actions and the possible consequences of using this product. You undertake to use this product only for legitimate and lawful purposes. TELESIN Digital Co., Ltd ("TELESIN") shall not be liable for any misuse, adverse effects, damages, injuries, penalties, or other legal consequences arising directly or indirectly from the use of this product. The user should follow all precautions mentioned herein. TELESIN reserves the right to interpret and modify this commitment within the limits of national laws and regulations.

Warranty Period

The warranty period for TELESIN products begins 6 months from the day you receive the product.

FCC Caution

15.19 Labelling requirements: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

15.21 Information to user: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

15.105 Information to the user: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.

RF warning for Portable device: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

IC Caution

This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

© TELESIN. All rights reserved.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.