Nekteck NK-FLM01

Contents

Nekteck Smart Shiatsu Foot & Calf Massager with Heat

Model: NK-FLM01

User Manual

Introduction

Thank you for purchasing the Nekteck Smart Shiatsu Foot & Calf Massager with Heat. This product is designed to provide a relaxing and therapeutic massage experience for your feet and calves, combining shiatsu massage with heat therapy to relieve tension and fatigue. Please read this manual carefully to ensure safe and optimal use of your new massager.

Important Safety Instructions

DANGER:

  • To reduce the risk of electric shock: Always unplug this appliance from the electrical outlet immediately after using and before cleaning.

WARNING:

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance.
  • Cleaning and user maintenance shall not be made by children without supervision.
  • The appliance has a heated surface. Persons insensitive to heat must be careful when using the appliance.
  • Use heated surfaces carefully as it may cause serious burns. Do not use over sensitive skin areas or where there's poor blood circulation. The unattended use of heat by children or incapacitated persons may be dangerous.
  • To reduce the risk of burns, fire, electric shock, or injury: An appliance should never be left unattended when plugged in. Unplug from the outlet when not in use, and before putting on or taking off parts.
  • Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury.
  • Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons.
  • Keep the cord away from heated surfaces.
  • Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
  • Do not carry this appliance by the power cord or use cord as a handle.
  • Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.
  • Never drop or insert any object into any opening.
  • Do not use outdoors.
  • Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
  • To disconnect, turn all controls to the off position, then remove plug from outlet.
  • Do not use the massager in close proximity to loose clothing or jewelry.
  • Keep long hair away from the massager while in use.

ELECTRIC SAFETY:

  • The appliance is only to be used with the power adapter that comes with the appliance.
  • Do not use this appliance if it has been dropped or if any part of the appliance (including the massager cloth cover, power cord, or power adapter) has been damaged.
  • Do not operate the appliance with wet hands or wet feet to reduce the risk of electric shock.
  • Turn off and unplug this appliance before moving it.
  • Unplug this appliance after use and before cleaning.
  • Unplug IMMEDIATELY and DO NOT use the product if it has malfunctioned or has been damaged in any way. Inspect the product by a qualified person.

SAVE THESE INSTRUCTIONS - HOUSEHOLD USE ONLY

Package Contents

  • 1 x Nekteck Smart Shiatsu Foot & Calf Massager with Heat
  • 1 x User Manual
  • 1 x Power Adapter

Specifications

Feature Detail
Product NameNekteck Smart Shiatsu Foot & Calf Massager with Heat
ColorBlack (Ivory variant also available)
Model NumberNK-FLM01
Rated Voltage12V DC === 5.0A
Rated Power60W
Dimensions18.5 x 10.1 x 16.3 in / 47 x 25.7 x 41.5 cm
Net Weight11.9 lbs / 5.4 kg
CertificationUL, FCC
ApplicationFoot, Calf, Arm
Item TypeMassage & Relaxation
OriginMainland China

Know Your Smart Foot & Calf Massager

The Nekteck Shiatsu Foot & Calf Massager with Heat combines shiatsu massage with heat therapy to relieve tension and fatigue for your feet and calves. It features an adjustable bar and adjustable feet to position the massager at different angles to fit your needs. Enjoy a comfortable massage experience.

Parts & Features Overview

Nekteck Smart Shiatsu Foot & Calf Massager with Heat
The Nekteck Smart Shiatsu Foot & Calf Massager with its control panel and app interface.
Part Feature
Rolling AreaCombines rolling, kneading, and scraping functions for optimum massage.
Vibrating AreaFocuses on massaging heels with vibrations.
Control PanelButtons to choose preferred massage modes, intensity levels, and power on/off.
AirbagsProvides air pressure by inflating and deflating.
Removable & Washable CoversFor easy cleaning.
Adjustable BarPositions the massager at an angle of about 54° for calf massage when sitting. (Cannot be used to carry the massager.)
Adjustable FeetPositions the massager at an angle of about 20° for sole massage when sitting, or calf massage when lying down.
Anti-slip Foot PadsEnsures stability during use.
HandleDesigned on both left and right sides for better portability.

Control Panel

Control Panel and Features of Nekteck Massager
The control panel with buttons for Vibration, Heat, Air Compression, Rolling, Timer, ON/OFF, and Wi-Fi Indicator.
  • Vibration Button: Controls vibration massage.
  • Heat Button: Activates/deactivates heat therapy.
  • Air Compression Button: Adjusts air compression levels.
  • Rolling Button: Controls rolling massage.
  • Timer Button: Sets massage duration.
  • ON/OFF Button: Powers the massager on or off.
  • Wi-Fi Indicator: Shows Wi-Fi connection status (slow flash for waiting, quick flash for triggered connection).

Before First Use

1. Using the Massager

  1. Remove the Smart Foot & Calf Massager and its accessories from the packaging box. Verify all package contents are included.
  2. Connect the DC power adapter to the massager and plug it into an outlet.
  3. If you experience mild pain during initial use, wear thick socks or place a towel under your feet to moderate pressure. As you get accustomed to the massage intensity, you can remove them for a deeper massage.

2. Nekteck App Setup

The Nekteck App allows for personalized control of your massager. Due to ongoing updates, the app interface may vary slightly from the manual. Follow in-app instructions for the most accurate setup.

A. Download the Nekteck App

Scan the QR code below or search for "NEKTECK" in the Apple App Store® (iOS) or Google Play Store (Android).

Nekteck App Screenshots for Personalized Massage Modes
Screenshots showing the Nekteck app interface for controlling massage modes and settings.

Note: For Android™ users, choose "Allow" to use Nekteck. It will not record personal information. The app is continually improved; follow in-app instructions for setup.

B. Create or Log In to Your Nekteck Account

Open the Nekteck App. If you have an account, tap "Log In". To create a new account, tap "Sign Up".

Note: An account is required for third-party services and products. A guest account will not work. An account also allows family and friends to control the massager.

C. Pairing with Nekteck App

  1. Turn on your smartphone's Bluetooth® and Wi-Fi®.
  2. Touch the device icon in the app and follow the in-app instructions to complete pairing.
  3. Tap '+' in the NEKTECK App and select your smart foot massager from the product list during the first connection. Once paired, it will appear in "Searching for Devices" for future use.
  4. Press and hold the power button on the massager for 5 seconds to turn on its Wi-Fi. The Wi-Fi indicator will blink, waiting for pairing. The app will display the connection status.
  5. If the app discovers the massager, tap "Add Device" and set up Wi-Fi.

Note: The Wi-Fi indicator will remain on once successfully connected. This setup is only required for the first time. Subsequent uses will automatically connect if the device is powered on and unplugged/replugged.

Operating Introductions

Massage Operation

Step 1: Turn On the Massager

Press the ON/OFF Button on the controller or the control panel. The massager will beep once and start in the default massage mode. Default settings are as follows:

Mode/Timer/Indicator Vibration Heat Air Compression Rolling Timer Wi-Fi
Default Intensity/TimeOFFHigh IntensityLow IntensityLow Intensity15 MinsFlashing slowly
Indicator Light ColorLight offRedGreenGreenGreen

Step 2: Adjust the Massage Modes and Intensity Levels

Press the corresponding mode buttons (Vibration, Heat, Air Compression, Rolling) to change intensity levels or turn the mode on/off. Each press cycles through available settings.

Mode Button Intensity Change Sequence
Vibration💫OFF (Default Light off) → Low Intensity (Green indicator) → High Intensity (Red indicator) → OFF
Heat🌡High Intensity (Default Red indicator) → Low Intensity (Green indicator) → OFF (Light off)
Air Compression💬Low Intensity (Green indicator) → Medium Intensity (Yellow indicator) → High Intensity (Red indicator) → OFF (Light off)
Rolling🐾Low Intensity (Default Green indicator) → High Intensity (Red indicator) → OFF (Light off)
Wi-Fi📶Flashing slowly (Default display) → Flashing quickly (Distribution network status) → Indicator light on (Connected device)

Note: Each of the 4 massage modes can be adjusted and run individually.

Step 3: Set the Massage Duration (Optional)

By default, the massager automatically shuts off after a 15-minute session. Press the Timer Button (🕔) to switch between 15 and 30 minutes.

Indicator Light Color Intensity Level Timer
GreenLow Intensity15 Mins
RedHigh Intensity30 Mins
YellowMedium Intensity (for Air Compression Only)N/A

Note: Medium Intensity is available for the Air Compression Mode ONLY.

Changing Time During Operation

If you wish to change the massage duration during an active session, please note the following:

Switch / Change Time When Massager Worked For How the Timer Continues to Work After Switching
From 15 to 30 mins0-15 minsThe previous working time will NOT be cleared and will be accumulated to the 30-min session. If you want an exact 30-min session, turn off and on the massager and set modes/time again.
From 30 to 15 mins< 15 minsThe previous working time will NOT be cleared and will be accumulated to the 15-min session.
From 30 to 15 mins≥ 15 minsThe massager will still run through the previous 30-min session. In this situation, please turn off and restart the massager to run the 15-min massage session.

Cautions: After each massage session, rest for 30 minutes. Do not use the massager for over 45 minutes a day. Start with the lowest intensity. Wear socks for initial use. Press ON/OFF to stop at any time.

Cleaning and Maintenance

To Clean:

  • Unplug the massager and allow it to cool down before cleaning. The fabric cover can be removed for cleaning.
  • Clean the base only with a soft, very slightly damp sponge or cloth.
  • Do not allow water or any other liquids to get into the massager.
  • Do not immerse the product in any liquid to clean.
  • Do not use abrasive cleaners, brushes, or strong chemicals to clean the product, as it might cause damage.

To Store:

  • Place the massager in its package box or a safe, dry, and cool place.
  • Avoid sharp edges and objects to protect the product from scratching or damaging.
  • Do not wrap the power cord around the product to avoid breakage.
  • Keep out of high temperatures.

Troubleshooting

If your Shiatsu Foot & Calf Massager is not operating correctly, refer to the chart below. Do not attempt to repair it yourself to avoid electric shock and voiding the warranty.

Problem Possible Cause Solution
The product does not workThe adapter is not plugged properlyPlug in again
The ON/OFF button is not pressedPress the ON/OFF button
The adapter is not the original oneCheck whether the adapter specifications are the same as the original adapter: 12V 5A
The product suddenly stops workingThe product turns off automatically after a 15-min or 30-min sessionPress the ON/OFF button again for another session
The DC connector is not connected properly to the DC power jackCheck and reconnect the connector and jack port
The product is overused and the overheat protection turns onUnplug the product and let it cool down completely before using it again
The device is pressed too hard and the massage rollers get stuckPress the ON/OFF button to restart the product
The heat function does not workThe heat button is not pressedPress the Heat Button
The product is abnormally warmThe product is likely to be overusedUnplug the product and let it cool down completely before using it again

User Tips

  • Start Gently: Especially for first-time users, begin with the lowest intensity settings and consider wearing thick socks or placing a towel to reduce initial pressure. Gradually increase intensity as you become accustomed to the massage.
  • Optimal Positioning: Utilize the adjustable bar (54° for calf massage when sitting) and adjustable feet (20° for sole massage when sitting, or calf massage when lying down) to find the most comfortable and effective angle for your massage.
  • Don't Overdo It: Limit each massage session to 15-30 minutes and ensure a 30-minute rest period between sessions. Do not exceed 45 minutes of total use per day to prevent overuse and potential discomfort.
  • App Control for Customization: Leverage the Nekteck app to customize massage times beyond the default 15/30 minutes, save your favorite settings, and control all functions remotely for a tailored experience.
  • Regular Cleaning: Keep your massager hygienic by regularly cleaning the removable fabric covers and wiping down the base with a damp cloth. Ensure it's unplugged and cool before cleaning.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Increase the separation between the equipment and receiver.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure requirements, please follow operation instructions as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.

Warranty and Support

Nekteck provides a warranty of 12 Months from the date of purchase. For any questions or concerns, please contact the customer service team.

Product Demonstration Video

Watch a demonstration of the Nekteck Smart Shiatsu Foot & Calf Massager, including unboxing, app control, and various usage positions for feet, calves, and arms.

© 2024 Nekteck. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.