Nekteck NK-FLM01

Contents

Nekteck Smart Shiatsu Foot & Calf Massager with Heat

Model: NK-FLM01

Introduction

Thank you for purchasing the Nekteck Smart Shiatsu Foot & Calf Massager with Heat. Nekteck is committed to providing high-quality products and great services. This manual provides detailed instructions for all functions and features of your new massager. Please read it carefully before use.

If you have any questions or concerns about using your new product, feel free to contact our helpful customer support team at support@nekteck.com.

Important Safety Instructions

Please read ALL instructions carefully before using the Foot & Calf Massager for the first time. Keep this manual for future reference. Improper use or unauthorized repairs are not permitted for safety reasons and will lead to loss of warranty. Basic safety precautions should always be followed to prevent fire, electric shock, and other serious injuries.

DANGER:

  • To reduce the risk of electric shock: Always unplug this appliance from the electrical outlet immediately after using and before cleaning.

WARNING:

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance.
  • Cleaning and user maintenance shall not be made by children without supervision.
  • The appliance has a heated surface. Persons insensitive to heat must be careful when using the appliance.
  • Use heated surfaces carefully as it may cause serious burns. Do not use over sensitive skin areas or where there's poor blood circulation. The unattended use of heat by children or incapacitated persons may be dangerous.
  • To reduce the risk of burns, fire, electric shock, or injury: An appliance should never be left unattended when plugged in. Unplug from the outlet when not in use, and before putting on or taking off parts.
  • Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock, or injury.

Additional Safety Precautions:

  • Close supervision is necessary when this appliance is used by, on, or near children, invalids, or disabled persons.
  • Keep the cord away from heated surfaces.
  • Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
  • Do not carry this appliance by the power cord or use cord as a handle.
  • Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.
  • Never drop or insert any object into any opening.
  • Do not use outdoors.
  • Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
  • To disconnect, turn all controls to the off position, then remove plug from outlet.
  • Do not use the massager in close proximity to loose clothing or jewelry.
  • Keep long hair away from the massager while in use.

Electric Safety:

  • The appliance is only to be used with the power adapter that comes with the appliance.
  • Do not use this appliance if it has been dropped or if any part of the appliance (including the massager cloth cover, power cord, or power adapter) has been damaged.
  • Do not operate the appliance with wet hands or wet feet to reduce the risk of electric shock.
  • Turn off and unplug this appliance before moving it.
  • Unplug this appliance after use and before cleaning.
  • Unplug IMMEDIATELY and DO NOT use the product if it has malfunctioned or has been damaged in any way. Inspect the product by a qualified person.

SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY

Package Contents

Please check the box to ensure all items are included:

  • 1 x Nekteck Smart Shiatsu Foot & Calf Massager with Heat
  • 1 x User Manual
  • 1 x Power Adapter

Specifications

FeatureDetail
Product NameNekteck Smart Shiatsu Foot & Calf Massager with Heat
ColorBlack
Model NumberNK-FLM01 (Also A06-SLM02-BKUS)
Rated Voltage12V DC === 5.0A
Rated Power60W
Dimensions18.5 x 10.1 x 16.3 in / 47 x 25.7 x 41.5 cm
Net Weight11.9 lbs / 5.4 kg
Package Length43 cm
Package Width38 cm
Package Height22 cm
Package Weight6.599 kg
CertificationUL, FCC
ApplicationFoot
Item TypeMassage & Relaxation

For more information, visit www.nekteck.com.

Product dimensions showing width 17.3in/44cm, height 8.7in/22.2cm, and foot length 11.0in/28cm, foot width 4.5in/11.5cm.
Figure: Product Dimensions. Fits most feet and calf sizes.

Know Your Smart Foot & Calf Massager

The Nekteck Shiatsu Foot & Calf Massager with Heat combines shiatsu massage with heat therapy to relieve tension and fatigue for your feet and calves. It features an adjustable bar and adjustable feet to position the massager at different angles to fit your needs.

Parts & Features Overview

Diagram showing the simulated massage experience with 3 Air Compression Levels, 2 Rolling Massage Levels, and 2 Vibration Massage Levels.
Figure: Simulated Massage Experience. The massager offers air compression, rolling, and vibration massage.
Image showing the control panel with buttons for Vibration, Heating, Air Compression, Rolling, Timer, and Connection Indicator. A smartphone app is also shown controlling the device.
Figure: Control Panel and App Interface. Enjoy a spa-quality shiatsu massage at home with various settings.
Part NameFeature
Rolling AreaCombines rolling, kneading, and scraping functions for optimum massage.
Vibrating AreaFocuses on massaging your heels with vibrations.
Control PanelPress buttons to choose preferred massage modes, intensity levels, or turn on/off the massager.
AirbagsProvides air pressure by inflating and deflating the airbags.
Removable & Washable CoversFor easy cleaning.
Adjustable BarPositions the massager at an angle of about 54° for calf massage when sitting. NOTE: The adjustable bar can NOT be used to carry the massager.
Adjustable FeetPositions the massager at an angle of about 20° for a sole massage when sitting, or calf massage when lying down.
Anti-slip Foot PadsEnsures stability during use.
HandleDesigned on both left and right sides for better portability.
Image showing a woman using the massager with the adjustable bar set at 54 degrees for calf massage and another image showing it set at 20 degrees for foot and arm massage.
Figure: Adjustable Bar Positions. Choose the most suitable position for your massage needs.

Control Panel Details

The control panel features several buttons and indicators:

  • Vibration Button: Controls vibration massage.
  • Heat Button: Controls heating function (113-131°F).
  • Air Compression Button: Controls air compression levels.
  • Rolling Button: Controls rolling massage levels.
  • Timer Button: Sets massage duration (5-30 minutes).
  • ON/OFF Button: Powers the massager on or off.
  • WIFI INDICATOR: Indicates Wi-Fi connection status. (Green light flashes slowly, and flashes quickly when Wi-Fi connection is triggered.)

Before First Use (Setup)

1. Unboxing and Initial Setup

  1. Remove the Smart Foot & Calf Massager and its accessories from the packaging box. Verify all package contents are included.
  2. Connect the DC power adapter to the massager and plug it into an outlet.
  3. If you feel mild pain during initial use, wear thick socks or place a towel under your feet for moderate pressure. As you get used to the intensity, you can remove them.
Video: Unboxing and initial setup of the Nekteck Foot & Calf Massager, demonstrating how to unpack and prepare the device for use, including adjusting the stand and connecting the power adapter.

2. Nekteck App Setup

Note: Due to ongoing updates, the NEKTECK app may look slightly different. Follow in-app instructions if there are differences.

A. Download the Nekteck App

Scan the QR code below or search for "NEKTECK" in the Apple App Store® (iOS) or Google Play Store (Android).

QR code for Nekteck app download, with 'Download on the App Store' and 'GET IT ON Google Play' logos.
Figure: Nekteck App Download. Scan the QR code or search in your app store.

Note: For Android™ users, choose "Allow" to use Nekteck. It won't be used to record personal, private information. Follow the instructions to finish setting up your Smart Foot & Calf Massager.

B. Create or Login to Your Nekteck Account

Open the Nekteck App. If you already have an account, tap Log In. To create a new account, tap Sign Up.

Note: You must create your own NEKTECK account to use third-party services and products. These will not work with a guest account. With a NEKTECK account, you can also allow your family and friends to control your Smart Foot & Calf Massager.

C. Pairing with Nekteck App

  1. Turn on your smartphone's Bluetooth® and Wi-Fi®.
  2. Touch the device icon in the app and follow the in-app instructions to touch the button to complete the pairing.
  3. Tap '+' in the NEKTECK App and select your smart foot massager machine from the Product list at the first connection. Once paired successfully, it will remain in "Searching for Devices". You can tap it directly the next time you use it.
  4. Press and hold the power button on the massager for 5 seconds to turn on Wi-Fi. The Wi-Fi indicator will blink and wait for pairing. The connection status will be displayed on the App.
  5. If the smart foot massager machine is discovered, tap "Add Device" and set up Wi-Fi.

Note: The Wi-Fi indicator will keep on once connected successfully.

Note: If you complete the connection and unplug the device, you can see the device status is off on your app. Please wait for 5 - 10 seconds after connecting the plug to the power source again to let the device automatically connect to the App. (The Wi-Fi indicator will blink for 5-10 seconds and then change to keep on once automatically connected.)

Operating Instructions

Massage Operation

Step 1: Turn On the Massager

Press the ON/OFF Button on the controller or the control panel. The massager will beep once and start in the default massage mode.

Mode/Timer/Indicator Light ColorVibrationHeatAir CompressionRollingTimerWIFI
Default Intensity/TimeOFFHigh IntensityLow IntensityLow Intensity15 MinsFlashing slowly
Indicator Light Colorlight offRedGreenGreenGreenGreen

Step 2: Adjust the Massage Modes and Intensity Levels (Optional)

Press the Mode Buttons (Vibration, Heat, Air Compression, Rolling) to change the intensity levels or turn on/off the corresponding mode. With each press of the button, the intensity level will change once, cycling through the sequence shown in the chart below.

ModeButtonIntensity Change Sequence
Vibration~OFF (Default Light off) → Low Intensity (Green indicator) → High Intensity (Red indicator)
Heat~OFF (Light off) → Low Intensity (Green indicator) → High Intensity (Red indicator)
Air Compression~OFF (Light off) → Low Intensity (Green indicator) → Medium Intensity (Yellow indicator) → High Intensity (Red indicator)
Rolling~OFF (Light off) → Low Intensity (Default Green indicator) → High Intensity (Red indicator)

Note: Each of the 4 massage modes can be adjusted and run individually.

Step 3: Set the Massage Duration (Optional)

By default, this massager will automatically shut off after a 15-minute massage session. Press the Timer Button to switch the timer between 15 and 30 minutes.

  • 15 Mins (Default Green indicator)
  • 30 Mins (Red indicator)

Note: If you want a 30-minute massage session instead of the default 15 minutes, it's highly recommended to set the time at the beginning. If you want to change the time during operation, please follow the chart below.

Switch/Change the TimeWhen the Massager Worked ForHow the Timer Continues to Work After Switching
From 15 to 30 mins0-15 minsThe previous working time will NOT be cleared and will be accumulated to the 30-min session. *If you want to have another exact 30-min session during the operation, turn off and on the massager and set the modes and time again.
From 30 to 15 mins< 15 minsThe previous working time will NOT be cleared and will be accumulated to the 15-min session.
From 30 to 15 mins≥ 15 minsThe massager will still run through the previous 30-min session. In this situation, please turn off and restart the massager to run the 15-min massage session.

App Functions:

  • Remote Control: All basic functions are available on the app.
  • Custom Timer: It can be timed on the App, not limited to 15 or 30 minutes of the machine itself.
  • Custom Mode Setting: Save your favorite settings, and you can select them for the next use.
  • Memory Function: The device will remember the current working mode status. It will become the default setting when restarting the machine the next time.

Cautions:

  • After each massage session, please rest for 30 minutes before starting the next massage session.
  • Each individual should NOT use the massager for over 45 minutes a day.
  • It is highly recommended to start the operation from the lowest intensity at the beginning of each use.
  • It is highly recommended to wear socks while using this massager.
  • If you want to stop the massage session, press the ON/OFF button at any time you like.

Cleaning and Maintenance

To Clean:

  • Unplug the massager and allow it to cool down before cleaning. The fabric cover can be removed for cleaning.
  • Clean the base only with a soft, very slightly damp sponge or cloth.
  • Do not allow water or any other liquids to get into the massager.
  • Do not immerse the product in any liquid to clean.
  • Do not use abrasive cleaners, brushes, or strong chemicals to clean the product, for it might cause damage to the product.

To Store:

  • Place the massager in its package box or a safe, dry, and cool place.
  • Avoid sharp edges and objects to protect the product from scratching or damaging.
  • Do not wrap the power cord around the product to avoid breakage.
  • Keep out of high temperatures.

Troubleshooting

Troubleshoot your problem by using the chart below. If the Shiatsu Foot & Calf Massager still does not operate correctly, it may be defective. Please contact customer support for assistance. DO NOT try to repair it by yourself, as there is a risk of electric shock.

ProblemPossible CauseSolution
The product does not workThe adapter is not plugged properlyPlug in again
The ON/OFF button is not pressedPress the ON/OFF button
The product suddenly stops workingThe adapter is not the original oneCheck whether the adapter specifications are the same as the original adapter: 12V 5A
The product turns off automatically after a 15-min or 30-min sessionPress the ON/OFF button again for another session
The DC connector is not connected properly to the DC power jackCheck and reconnect the connector and jack port
The product is overused and the overheat protection turns onUnplug the product and let it cool down completely before using it again
The device is pressed too hard and the massage rollers get stuckPress the ON/OFF button to restart the product
The heat function does not workThe heat button is not pressedPress the Heat Button
The product is abnormally warmThe product is likely to be overusedUnplug the product and let it cool down completely before using it again

User Tips

  • For optimal comfort, especially during initial uses, consider wearing thick socks or placing a towel inside the massager to adjust pressure.
  • The app offers greater control over massage duration and allows you to save personalized massage settings for future use.
  • Remember to allow the massager to cool down if it becomes abnormally warm or if the overheat protection activates.

Warranty and Customer Support

Nekteck provides all of our customers with a warranty of 12 Months from the date of purchase.

If you have any questions or concerns regarding your new product, please contact our customer service team at support@nekteck.com. We will reply to your message within 24 hours!

Please include your Order ID in your email when you are contacting Customer Support for faster solutions.

Disclaimer

Nekteck and its subsidiaries assume no liability for damage caused by the use of the product other than for its intended use or as instructed in the user manual. Some countries or states do not allow this exclusion or limitation of incidental or consequential losses so the foregoing disclaimer may not apply to you.

IMPROPER USE OF NEKTECK'S PRODUCTS INVOLVES SERIOUS RISKS INCLUDING INJURY AND DISABILITY. YOU UNDERSTAND THAT BY KEEPING, USING, OR ALLOWING USE OF NEKTECK'S PRODUCTS, YOU AGREE TO THE FOLLOWING:

  1. NEKTECK ACCEPTS NO RESPONSIBILITY FOR ANY INJURY WHICH MIGHT OCCUR WHILE USING NEKTECK'S PRODUCTS.
  2. USE LIMITATION. YOU MAY NOT MODIFY AND REPRODUCE NEKTECK'S PRODUCTS. YOU SHALL CAREFULLY INSPECT NEKTECK'S PRODUCTS BEFORE EACH USE TO ENSURE IT HAS NOT BEEN DAMAGED AND IS FULLY FUNCTIONAL.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Increase the separation between the equipment and receiver.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instructions as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.