OBD2 Scanner V318

Contents

V318 OBD2 Scanner Car Fault Diagnostic Instrument User Manual

Automobile OBD Diagnostic Instrument

1. Product Overview

The V318 is a gasoline car code reader designed to support nine standard OBD II/EOBD protocols. This plug-and-play device allows for quick reading of car fault information and vehicle parameters, offering a comprehensive set of functions for fault diagnosis.

V318 Car Diagnostic Tool with screen showing menu options and key features
Figure 1: V318 Car Diagnostic Tool highlighting its main features including 10 languages, fault code query, and real-time data.
V318 Car Fault Diagnosis Instrument showing device and list of functions
Figure 2: The V318 instrument with a list of its powerful functions such as reading and erasing codes, viewing freeze frames, and O2 sensor data.

1.1 Application Range

This OBD II / EOBD decoder is specifically designed for all vehicles compliant with the OBD II standard. This includes 1996 and newer automobiles and light trucks sold in the USA, as required by the United States Environmental Protection Agency, as well as domestic, Asian, and European vehicles. A small number of 1994 and 1995 petrol vehicles may also be OBD II compliant; verify by checking the Vehicle Emission Control Information (VECI) label, typically found under the engine jacket or near the radiator. All compliant vehicles must have a "General" 16-pin Data Link Connector (DLC) located below the instrument panel.

2. Safety Precautions

  • Do not use abrasive cleaners to clean this product.
  • Do not allow this product to be heated or placed close to a source of fire.
  • Do not expose this product to direct sunlight for a long time.
  • Do not attempt to disassemble this product or make any modifications, as it does not contain any user-serviceable components.
  • If you do not plan to use this product for a long time, store it in a dry environment to avoid extreme temperatures and dust.

3. Setup

3.1 Tool Description

Universal car fault diagnosis instrument with labeled parts
Figure 3: Diagram of the V318 tool with its main components labeled.
  1. Diagnostic Joint (1): Connects the decoder to the vehicle's Data Link Connector (DLC).
  2. LCD Display (2): Shows detection results and menu options.
  3. Up Button (4): Navigates up through menus and submenus.
  4. ESC Button (5): Cancels selection or operation, or returns to the previous menu.
  5. I/M Button (I/M): Quick checks for emissions readiness and drive cycle verification.
  6. OK Button (6): Confirms selection or operation.
  7. Down Button (7): Navigates down through menus and submenus.

3.2 Included Accessories

The product package typically includes:

  • V318 OBD2 Scanner Unit
  • User's Manual
  • OBD2 Wire (for power supply and communication)
Packing list showing the V318 device, its box, and the user manual
Figure 4: Contents of the V318 product package.

3.3 Connecting to Vehicle Power Supply

The V318 decoder is powered directly by the vehicle's Data Link Connector (DLC). Follow these steps to connect:

  1. Turn off the vehicle's ignition switch.
  2. Locate the vehicle's 16-pin Data Link Connector (DLC). This is typically found under the dashboard on the driver's side.
  3. If your vehicle has a plastic cover plate over the DLC, remove it before proceeding.
  4. Insert the OBD II wire connector firmly into the vehicle's DLC.

3.4 Initial Product Setup

After connecting the device to your vehicle, you can configure basic settings:

Product Setup screen displaying Language and Unit Of Measure options
Figure 5: The Product Setup menu, allowing selection of language and measurement units.
  • Language: Select your preferred language from the available options (German, Dutch, English, Spanish, French, Italian, Russian, Chinese, Japanese, Korean).
  • Unit Of Measure: Set the measurement units to either imperial or metric.

4. Operating Instructions

4.1 OBD II Diagnosis Procedure

  1. Ensure the ignition switch is turned off before connecting.
  2. Locate and connect the OBD II wire to the vehicle's 16-pin Data Link Connector (DLC).
  3. Turn on the ignition switch. The engine can be either stopped or running.
  4. Press the Return/Confirm button on the V318 to enter the diagnostic menu.
  5. The device will display a series of OBD2 protocol information until the vehicle protocol is detected.

Troubleshooting "Connection Error!"

If "Connection error!" is displayed on the screen, check the following:

  • Confirm the ignition switch is turned on.
  • Ensure the OBD II connector is securely connected to the vehicle's DLC.
  • Confirm that your vehicle is OBD2 standard compliant.
  • Turn off the ignition switch, wait 10 seconds, then turn it on again and retry.

If the "Connection error" persists, there may be a communication problem between the decoder and the vehicle. Please refer to the support section for further assistance.

4.2 Diagnostic Functions

Navigate through the diagnostic menu using the Up/Down buttons and confirm selections with the OK button.

4.2.1 Read Codes

This function allows you to retrieve Diagnostic Trouble Codes (DTCs) from the vehicle's computer.

  1. From the Diagnostic Menu, select "Read Codes".
  2. Press Return/Confirm.
  3. The screen will display the DTCs and their definitions. The control module number, diagnostic code order, total number of codes, and code type (general or manufacturer-specific) will be shown in the upper right corner.

If no codes are detected, "Code is not stored in module!" will be displayed. If a retrieved DTC is manufacturer-specific, "Controlled by manufacturer" will appear.

Screen showing diagnostic results for Trouble Codes, DTCs Cleared status, and O2 Sensor readings
Figure 6: Example screen displaying trouble codes and system readiness status.

4.2.2 Erase Codes

Caution: Deleting diagnostic codes may also delete "Freeze Frame" data and enhanced manufacturer data. Additionally, I/M readiness monitor statuses for all vehicle monitors will be reset to a non-ready and non-finish state. Do not delete codes before a qualified technician has thoroughly checked the system.

  1. From the Diagnostic Menu, select "Erase Codes".
  2. Press Return/Confirm.
  3. A warning message will appear, asking for confirmation. Select "YES" to proceed.
  4. If successful, "Delete is finished !" will be displayed. If unsuccessful, "Delete is failed. Rotate the key in the case of engine is turned off!" will appear.

If deletion fails, try turning off the engine and then clearing the fault code when the power is on. Wait several seconds or press any button to return to the Diagnostic menu.

4.2.3 View Freeze Frame

Freeze Frame data captures engine conditions at the moment a Diagnostic Trouble Code (DTC) was set.

  1. From the Diagnostic Menu, select "View Freeze Frame".
  2. The screen will display retrieved data such as DTCFRZF, FUELSYS1, LOAD_PCT(%), ETC(°C), and SHRTFT(%).

The "x/x" in the upper right corner indicates the total frame coverage and the current displaying data's serial number. If no Freeze Frame data is available, "Freeze Frame is not stored" will be displayed.

4.2.4 I/M Readiness

The I/M Readiness function checks the operational status of the vehicle's emission system, which is crucial for state emission testing.

  1. From the Diagnostic Menu, select "I/M Readiness".
  2. The device may offer two types of tests: "Since DTCs Cleared" and "This Drive Cycle". Select the desired option.
  3. The screen will display the status of various monitors, including MIL Status, Misfire Monitor, Fuel System Mon, Component Monitor, Catalyst Mon, Htd Catalyst, and EVAP System Mon.

4.2.5 Read Vehicle Information

This function retrieves important vehicle identification data.

  1. From the Diagnostic Menu, select "Vehicle Info.".
  2. Use the Up/Down buttons to select the desired information: Vehicle ID Number (VIN), Calibration ID, or Calibration Verification Number (CVN).
  3. Press Confirm to view the selected information.

Models manufactured after 2000 typically support vehicle performance tracking in mode 9.

4.2.6 Data Stream

View real-time engine data flow information.

  1. From the Diagnostic Menu, select "Data Stream".
  2. The screen will display current engine data parameters such as FUELSYS2, LOAD_PCT(%), ETC(°C), SHRTFT1(%), LONGFT1(%), SHRTFT2(%), and LONGFT2(%).

4.2.7 RealTime Curve

Monitor various engine parameters in a graphical, real-time curve display.

  1. From the Diagnostic Menu, select "RealTime Curve".
  2. Press Confirm to view speed waveform displays, including Car Speed, Calculate Load Value, Engine Coolant Temp, and Engine RPM.
  3. Press Confirm again to access the calculate load value interface.

4.2.8 Oxygen Sensor

View real-time data from the oxygen sensors.

  1. From the Diagnostic Menu, select "O2 Sensor".
  2. Use the Up/Down buttons to view the current data flow, including O2SLOC, O2B1S1(V), O2B1S2(V), etc.

4.2.9 Fuel Evaporation Control System (EVAP)

Monitor the status of the EVAP system.

  1. From the Diagnostic Menu, select "EVAP".
  2. Use the Up/Down buttons to view the current data flow, including EVAP_PCT(%) and EVAP_VP(Pa).

4.2.10 Diagnostic Code Query (DTC Lookup)

Look up definitions for specific diagnostic trouble codes.

  1. From the main menu, select "DTC Lib" (DTC Lookup).
  2. Use the Up/Down buttons to adjust and input the desired code.
  3. Press Confirm to query the code's definition.

4.2.11 Battery Voltage

Check the current voltage of your car's battery in real-time.

  1. From the main menu, select "Battery".
  2. The screen will display the current voltage value.
Screen displaying battery voltage of 11.7V
Figure 7: Example screen showing real-time battery voltage reading.

5. Specifications

Table of Product Parameters for Model V318
Figure 8: Detailed product parameters for the V318 model.
Parameter Value
Model V318
Display 160*128 dpi, 1.8-inch TFT color screen
Operating Temperature 0 ~ 60 °C (32 ~ 140 ℉)
Storage Temperature -20 ~ 70 °C (-4 ~ 158 ℉)
Operating Voltage Vehicle batteries supply 9.0 to 16.0V
Product Size 125*62*21mm
Package Dimensions 160*70*60mm
Product Weight 144g (with packaging 198g)
Supported Protocols
  • SAE J1850 PWM (41.6 Kbaud)
  • SAE J1850 VPW (10.4 Kbaud)
  • ISO9141-2 (5 baud init, 10.4 Kbaud)
  • ISO14230-4 KWP (5 baud init, 10.4 Kbaud)
  • ISO14230-4 KWP (fast init, 10.4 Kbaud)
  • ISO15765-4 CAN (11bit ID, 500 Kbaud)
  • ISO15765-4 CAN (29bit ID, 500 Kbaud)
  • ISO15765-4 CAN (11bit ID, 250 Kbaud)
  • ISO15765-4 CAN (29bit ID, 250 Kbaud)
Supported Languages English, German, French, Spanish, Italian, Russian, Dutch, Chinese, Japanese, Korean

6. Maintenance

The V318 OBD2 Scanner is designed for durability and does not require user maintenance. To ensure its longevity, follow the safety precautions outlined in Section 2.

  • Keep the device clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners.
  • Store the device in a dry place, away from direct sunlight, extreme temperatures, and dust.
  • Do not attempt to open or repair the device, as it contains no user-serviceable parts and doing so may void any applicable warranty.

7. Troubleshooting

If you encounter issues with the V318, refer to the "Troubleshooting 'Connection Error!'" subsection in Section 4.1. For other issues, consider the following:

  • Device not powering on: Ensure the OBD2 cable is securely connected to the vehicle's DLC and the vehicle's ignition is on. The device draws power directly from the vehicle.
  • Inaccurate readings: Ensure the vehicle is fully compliant with OBD II standards. Check for any loose connections.
  • Codes not clearing: Follow the steps in Section 4.2.2 carefully. If the issue persists, consult a professional technician.

8. User Tips

  • The V318 is compact and easy to handle, making it convenient for personal use.
  • It powers on automatically when plugged into the car's OBD port, simplifying operation.
  • The device supports multiple languages, including Russian and Korean, with good translation quality, enhancing usability for a diverse range of users.
  • It can effectively read and clear even minor error codes, such as those caused by a loosely closed fuel cap.
  • Consider the V318 a good value for money for basic to intermediate car diagnostics.

9. Frequently Asked Questions (FAQ)

Q: Does the V318 work on a Yamaha R3 if I have an adapter cable for 16 pins?
A: The V318 is primarily designed as a gasoline car code reader and is compatible with vehicles that adhere to the OBD II standard. While some motorcycles may have OBD-like systems, compatibility with specific motorcycle models like the Yamaha R3, even with an adapter, is not guaranteed as the device is optimized for automotive OBD II protocols. Please verify your vehicle's specific diagnostic protocol requirements.

10. Support

For further assistance or detailed documentation, please refer to the official user manual PDF:

View User Manual (PDF)

Compatibility Notice: This product is not compatible with new energy vehicles, hybrid vehicles, diesel vehicles, or models that do not adhere to the OBD2 agreement.

Disclaimer: The manufacturer is not responsible for product damage resulting from abnormal use, improper storage, exposure to moisture or humidity, unauthorized modification or maintenance, misuse, negligence, abuse, accident, alteration, improper installation, damage caused by transportation, external reasons (such as collision, fire, flood, sand, dust, storm, lightning, earthquake, weather conditions, natural disasters), battery leakage, theft, blown fuse, or incorrect use of any power supply. These conditions may void any applicable warranty.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.