Introduction
Thank you for purchasing the High Lumens Rechargeable LED Flashlight. This manual provides important information regarding the safe and efficient use, maintenance, and troubleshooting of your new flashlight. Please read this manual carefully before use and retain it for future reference.

Safety Warnings
- Do not illuminate eyes directly to avoid eye injury. The flashlight produces a very bright beam.
- Ensure all threads are tightened when using the flashlight. Loose connections may result in no light or dim light.
- Keep the flashlight away from direct sunlight or high temperatures.
- Avoid contact with water, chemicals, and corrosive gases for extended periods. While waterproof, prolonged exposure to corrosive elements can cause damage.
- Non-professionals should not disassemble the flashlight to prevent damage to the circuit board.
- Do not reverse the battery polarity, as this will damage the circuit board.
Setup
Battery Installation
- Twist off the tail cover of the flashlight.
- Carefully distinguish the positive (+) and negative (-) poles of the battery. The positive pole should face the LED (inside the tube), and the negative pole should face the tail cover (outside the tube).
- Insert the battery correctly according to the polarity.
- Ensure that all threads (middle and tail sections of the flashlight tube) are tightened to ensure good electrical contact. Loose connections can prevent the flashlight from operating or cause dim light.
Note: A diagram for battery installation is typically included in the physical manual. Please refer to the textual instructions above for proper installation.
Initial Charging
Before first use, remove the transparent insulating film from the battery. Ensure the battery is fully charged before operating the flashlight. The flashlight features a USB-C charging port for quick charging (2-4 hours).

Operation
Power On/Off and Mode Selection
The flashlight features a single button for power control and mode switching. Press the button to turn the flashlight on. Subsequent presses will cycle through the 5 lighting modes:
- High: Maximum brightness for powerful illumination.
- Medium: Balanced brightness for general use.
- Low: Reduced brightness for extended battery life or close-range tasks.
- Flash: Strobe mode for signaling or disorientation.
- SOS: Emergency signal mode.
To turn off the flashlight, press and hold the power button for a few seconds, or cycle through all modes until it turns off.

Adjustable Focal Length (Zoom Function)
The flashlight features an adjustable focal length, allowing you to switch between a wide floodlight and a narrow, focused beam. To adjust, simply slide the head of the flashlight forward or backward.
- Wide Beam: Provides a broad area of illumination, ideal for lighting up large spaces.
- Narrow Beam: Concentrates the light into a powerful, long-distance beam, suitable for spotting distant objects.

Power Display
The flashlight is equipped with a power display to indicate the remaining battery charge. Typically, four blue indicator lights represent 100%, 75%, 50%, and 25% charge levels. Monitor these indicators to know when to recharge your flashlight.
Maintenance
Cleaning
- Keep the inner wall of the lamp cup clean. Do not wipe it with your hand or any hard object, as this may scratch the surface.
- To clean the lens, gently remove any fingerprints or smudges using a cotton swab and a specialized lens cleaner.
- Wipe the exterior of the flashlight with a soft, damp cloth. Do not use abrasive cleaners or solvents.
Battery Care and Storage
- If the flashlight's brightness changes significantly during use, turn it off and recharge the battery promptly to prevent over-discharge.
- For batteries not used for a long time, ensure they are fully charged before storage. To prevent chemical corrosion and maintain battery health, charge and discharge the battery once every three months.
- Store the battery in a cool, dry place away from direct sunlight and extreme temperatures.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Flashlight does not turn on or produces dim light. |
|
|
| Flashlight brightness decreases significantly during use. | Battery is running low or is over-discharged. | Turn off the flashlight and recharge the battery promptly. |
| Flashlight is damaged after battery installation. | Battery was inserted with reversed polarity. | Always ensure correct battery polarity during installation to prevent circuit board damage. |
Specifications
| Feature | Detail |
|---|---|
| Item Type | FLASHLIGHTS |
| Function | Hard Light |
| Lumen | 1200 (Max 990,000 Lumens advertised) |
| Lighting Distance | > 500 meters (Max 3600 Feet advertised) |
| Wattage | 30W |
| Switch Mode | High/Middle/Low (Also Flash/SOS) |
| Support Dimmer | 5-8 files (modes) |
| Zoom | Yes (Adjustable Focal Length) |
| Waterproof | Yes |
| Charger | Rechargeable (USB-C) |
| Is Batteries Included | Yes (1x 26650 3.7V battery) |
| Body Material | Aluminum alloy |
| Certification | CE |
| Origin | Mainland China |
| Package Dimensions (L x W x H) | 18 cm x 13 cm x 6 cm |
| Package Weight | 0.456 kg |
| Running Time (on Low) | Up to 12 hours |
| Charging Time | 2-4 hours |


User Tips
- For optimal performance, always ensure the battery is fully charged before extended use.
- When storing the flashlight for long periods, remove the battery if possible, or follow the quarterly charge/discharge cycle.
- Utilize the zoom function to adapt the beam to your needs: wide for area lighting, narrow for distance.
- The power indicator lights are a useful guide; recharge when only one or two lights remain to avoid complete discharge.
Frequently Asked Questions (FAQ)
- Q: Is the battery included with the flashlight?
- A: Yes, a 26650 3.7V rechargeable battery is included.
- Q: What type of battery does this flashlight use?
- A: It uses a 26650 3.7V rechargeable battery. It does not use AA or AAA batteries.
- Q: What is the maximum lighting distance?
- A: The flashlight can illuminate distances greater than 500 meters (up to 3600 feet).
- Q: How long does the battery last on a single charge?
- A: On the low setting, the flashlight can operate for up to 12 hours.
- Q: How long does it take to fully charge the flashlight?
- A: It takes approximately 2-4 hours for a full charge using the USB-C port.
Warranty and Support
For detailed warranty information and customer support, please refer to the official user manual PDF available at: User Manual (PDF).
If you encounter any issues not covered in this manual, please contact the seller or manufacturer for assistance.