8BitDo Lite 2 Bluetooth Gamepad Instruction Manual

Introduction

The 8BitDo Lite 2 Bluetooth Gamepad is a versatile and ultra-portable controller designed for a wide range of gaming platforms. Its compact size and lightweight design make it an ideal companion for gaming on the go. This manual provides detailed instructions on how to set up, operate, and maintain your gamepad, ensuring an optimal gaming experience.

Setup

Gamepad Layout

Familiarize yourself with the gamepad's buttons and indicators:

• L/R Buttons: Shoulder buttons.
• L2/R2 Buttons: Trigger buttons.
• L3/R3 Buttons: Clickable joysticks.
• D-pad: Directional pad.
• Home Button: System button.
• Asterisk Button: Special function button (e.g., Turbo).
• Mode Switch: Selects the operating mode (S for Switch, D for Android).
• Pair Button: Initiates Bluetooth pairing.
• Status LED: Indicates connection status and player number.
• Power LED: Indicates power and charging status.

Bluetooth Connection

Before use, ensure your device's system and the Lite 2 gamepad are updated to the latest version.

For Nintendo Switch

1. Set the mode switch to the S position.
2. Press the HOME button to turn on the controller. The Status LED will start to rotate from left to right.
3. For the very first time only, press and hold the PAIR button for approximately 3 seconds to enter pairing mode. The Status LED will stop blinking for a short moment then start to rotate again.
4. Go to your Switch Home page, select "Controllers", then "Change Grip/Order" and wait for the connection.
5. Upon successful connection, the controller will vibrate briefly, and the Status LED will become solid.

Note: NFC scanning, IR camera, HD rumble, notification LED, and system wake-up are not supported by this controller on Nintendo Switch.

For Android Devices

1. Set the mode switch to the D position.
2. Press the HOME button to turn on the controller. Status LED 1 will start to blink.
3. For the very first time only, press and hold the PAIR button for approximately 3 seconds to enter pairing mode. The Status LED will stop blinking for a short moment then start to rotate again.
4. Go to your Android device's Bluetooth settings, and pair with "8BitDo Lite 2".
5. Upon successful connection, the controller will vibrate briefly, and the Status LED will become solid.

For iOS, iPadOS, tvOS, macOS, and Raspberry Pi

While specific instructions for these platforms are not detailed in the provided manual snippets, the general Bluetooth pairing process should be similar to Android:

1. Set the mode switch to the D position (for general Bluetooth compatibility).
2. Press the HOME button to turn on the controller.
3. Press and hold the PAIR button for approximately 3 seconds to enter pairing mode.
4. On your device (iOS, iPadOS, tvOS, macOS, Raspberry Pi), navigate to Bluetooth settings and select "8BitDo Lite 2" to pair.
5. The controller will vibrate and the Status LED will become solid upon successful connection.

Wired Connection

For Nintendo Switch

1. Ensure "Pro Controller Wired Communication" is enabled in your Switch's System Settings > Controllers and Sensors.
2. Set the mode switch to the S position.
3. Connect the controller to your Switch dock via a USB cable.
4. Wait until the controller is successfully recognized by your Switch to play.

For Android Devices

1. Ensure your Android device supports OTG (On-The-Go) functionality. Consult your device manufacturer for details.
2. Set the mode switch to the D position.
3. Connect the controller to your Android device via a USB cable.
4. Wait until the controller is successfully recognized by your Android device to play.

Operating Instructions

Turbo Function

The Turbo function allows a button to be repeatedly pressed automatically while held down.

1. Hold the button you wish to set Turbo to.
2. While holding the button, press the ASTERISK button to activate the Turbo function.
3. Repeat the process (hold button + press ASTERISK) to deactivate the Turbo function.

Note: The D-Pad, Left Stick, Right Stick, Home, Select, and Start buttons do not support the Turbo function. The Turbo function is also not available when the controller is connected to a Nintendo Switch.

Motion Control (Nintendo Switch Only)

The 8BitDo Lite 2 features built-in six-axis sensory chips, providing motion control capabilities for an immersive gaming experience on Nintendo Switch.

Vibration

The gamepad includes a vibration feature to provide tactile feedback during gameplay, enhancing immersion.

Video demonstrating the 8BitDo Lite 2 gamepad's features, including its compact size, multi-platform compatibility, vibration, and motion control.

Battery Information

The 8BitDo Lite 2 gamepad is equipped with a 480mAh rechargeable lithium-polymer battery.

• Charging Time: Approximately 1 hour.
• Play Time: Approximately 20 hours on a full charge.

Power LED Status Indicators:

• Red LED blinks: Low battery.
• Red LED stays solid: Charging.
• Red LED turns off: Fully charged.

The controller will automatically turn off if not connected within 1 minute after powering on, or if there is no operation for 15 minutes after a Bluetooth connection. The controller will remain on during a wired connection.

Maintenance

To ensure the longevity and optimal performance of your 8BitDo Lite 2 Gamepad, follow these maintenance guidelines:

• Cleaning: Use a soft, dry cloth to wipe the controller. Avoid using harsh chemicals or abrasive materials.
• Storage: Store the gamepad in a cool, dry place away from direct sunlight and extreme temperatures.
• Battery Care: Avoid fully discharging the battery frequently. For long-term storage, charge the battery to about 50% to prolong its lifespan.
• Avoid Physical Damage: Do not drop the controller or expose it to excessive force.

Troubleshooting

Connection Issues

• Controller not turning on: Ensure the battery is charged. Check the Power LED status.
• Unable to pair via Bluetooth:
  • Verify the mode switch is set correctly (S for Switch, D for Android/other).
  • Ensure you are pressing the PAIR button for 3 seconds to enter pairing mode (especially for the first time).
  • Check your device's Bluetooth settings to ensure it's scanning and the controller is discoverable.
  • Try restarting both the controller and your device.
• Wired connection not working:
  • For Nintendo Switch, confirm "Pro Controller Wired Communication" is enabled in system settings.
  • For Android, ensure your device supports OTG functionality.
  • Try a different USB cable or USB port.

Functionality Issues

• Turbo function not working:
  • Ensure you are not trying to apply Turbo to unsupported buttons (D-Pad, sticks, Home, Select, Start).
  • Remember that Turbo is not available in Nintendo Switch mode.
• Motion control not working on Switch:
  • Ensure your Switch system is updated to the latest version.
  • Verify the game you are playing supports motion controls.

Specifications

User Tips

• The 8BitDo Lite 2 connects very quickly and reliably with various devices, making it convenient for seamless gaming.
• Its compact and useful design ensures a perfect gaming experience across compatible platforms.

Frequently Asked Questions (FAQ)

Q: Is the 8BitDo Lite 2 compatible with TESLA?

A: The 8BitDo Lite 2 is primarily designed for Nintendo Switch, Android, iOS, iPadOS, tvOS, macOS, and Raspberry Pi. Compatibility with TESLA vehicles is not officially listed or guaranteed.

Warranty and Support

For further information, additional support, or to check for firmware updates, please visit the official 8BitDo support website:

support.8bitdo.com

You can also refer to the comprehensive user manual available in PDF format for more detailed instructions and diagrams:

View User Manual (PDF)