1. Product Overview
The eletechsup DDIS24QC is a series of isolated DC-DC buck converters designed for industrial and automation applications. These modules convert a wide DC input voltage range (18-75V) into stable, isolated DC outputs of 3.3V, 5V, or 12V. Featuring various protection functions and a convenient DIN rail housing, they are ideal for powering PLCs, RS485 communication systems, IO modules, relays, and LED lighting.
Figure 1: DDIS24QC Isolated DC-DC Converter with DIN Rail Housing
2. Safety & Warnings
Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
- Handle with care to avoid cuts or injuries.
- Ensure proper ventilation around the module during operation.
3. Specifications
The DDIS24QC series offers different output voltage versions. Please refer to the specific version for detailed electrical characteristics.
| Attribute | Value |
|---|---|
| Input Voltage Range | DC 18V ~ 75V (Wide Voltage Input) |
| Output Type | Isolated DC-DC |
| Isolation Voltage | 2250V (basic insulation) |
| Switching Frequency | 450 kHz |
| Input Protection | UVLO (Under Voltage Lockout) |
| Output Protection | OCP (Over Current Protection), OVP (Over Voltage Protection), OTP (Over Temperature Protection) |
| Minimum Load Required | No |
| Operating Temperature | –40°C to +105°C |
| Dimensions (L x W x H) | 87 x 59 x 35mm |
Version-Specific Specifications:
| Version | Output Voltage / Current | Max. Output Current (Short Time) | Max. Output Current (Long Time) | Efficiency | Weight |
|---|---|---|---|---|---|
| 3.3V Version | 3.3V / 2.5A | 3.5A | 2.5A | 85% @ 3.3V/2.5A | 60g |
| 5V Version | 5V / 2A | 3A | 2A | 85% @ 5V/2A | 60g |
| 12V Version | 12V / 1.3A | 1.4A | 1.2A | 87% @ 12V/1.3A | 58.5g |
4. Setup and Installation
4.1 Before First Use
- Remove all protective films from the device.
- Ensure the module is free from any physical damage.
- Verify that the input voltage source matches the specified range (DC 18-75V).
- Confirm that the load connected to the output does not exceed the module's maximum current rating for the selected output voltage.
4.2 Wiring Instructions
The DDIS24QC converter features clearly labeled input and output terminals for easy connection. Always ensure power is disconnected before making any wiring changes.
- Input Connection: Connect your DC 18-75V power source to the 'IN+' and 'IN-' terminals. Ensure correct polarity.
- Output Connection: Connect your load to the 'OUT+' and 'OUT-' terminals. Ensure correct polarity for your connected device.
Figure 2: Wiring Diagram and Output Current Details for DDIS24QC Versions
Note on Output Current: The image above details the maximum output current for short-time and long-time operation for each voltage version. Always operate within the long-time maximum current for stable performance.
4.3 DIN Rail Mounting
The DDIS24QC is designed for easy mounting on standard DIN rails. Simply align the module with the DIN rail and snap it into place. Ensure it is securely fastened to prevent accidental dislodgement.
Figure 3: DDIS24QC DIN Rail Mounting Views
5. Operating Instructions
- After completing all wiring and mounting, apply the DC 18-75V input voltage to the module.
- The module will automatically convert the input to the specified output voltage (3.3V, 5V, or 12V depending on the version).
- Monitor the connected load to ensure it operates within its specified parameters and does not draw excessive current from the converter.
- The module is designed for continuous operation within its specified temperature and current limits.
5.1 After Use
- To power down, disconnect the input voltage source.
- If storing the device, ensure it is turned off and kept in a dry place, away from children.
6. Maintenance
- Cleaning: Keep the module clean and free from dust and debris. Use a dry, soft cloth for cleaning. Do not use liquids or abrasive cleaners.
- Inspection: Periodically inspect the module for any signs of physical damage, loose connections, or discoloration.
- Ventilation: Ensure that the module's ventilation openings are not obstructed to allow for proper heat dissipation.
- Environmental Conditions: Operate and store the module within the specified temperature and humidity ranges. Avoid environments with excessive vibration or corrosive gases.
7. Troubleshooting
- No Output Voltage:
- Check if the input voltage is within the 18-75V range and connected with correct polarity.
- Verify that the input power source is active.
- Ensure the output load is not short-circuited or drawing excessive current, which might trigger protection mechanisms.
- Output Voltage is Unstable or Incorrect:
- Check for loose wiring connections at both input and output terminals.
- Ensure the load current does not exceed the module's long-time maximum output current. Overloading can cause voltage drops or instability.
- Verify that the ambient operating temperature is within the specified range (-40°C to +105°C).
- Module Becomes Hot or Shuts Down:
- This indicates that the module's over-temperature protection (OTP) or over-current protection (OCP) may have been triggered.
- Immediately disconnect power.
- Check the load for any short circuits or excessive current draw.
- Ensure adequate ventilation around the module.
- Allow the module to cool down before re-applying power. If the issue persists after verifying the load and environment, the module may be faulty.
8. User Tips
- Proper Load Matching: Always ensure your connected load's power requirements are well within the converter's specified long-time maximum output current to prevent overheating and potential damage to both the converter and the connected components.
- Secure Connections: Double-check all wiring connections for tightness and correct polarity before applying power. Loose connections can lead to intermittent operation or damage.
- Environmental Awareness: While robust, avoid installing the converter in extremely dusty, humid, or poorly ventilated areas to maximize its lifespan and reliability.
9. Manufacturer Information
Manufacturer: Guangzhou Keshen Electronic Technology Co., Ltd
Address: CN-Room 301, No. 8-1 Beixin Street, Kemulang Aotou, Tianhe District, Guangzhou City
Contact: eletechsup@163.com
EU Authorized Representative: TOCYA TRADING
Address: 79 rue de patay, 75013, Paris
Contact: TOCYATRADING75013@outlook.com
10. Compliance Information
This product is designed to comply with applicable safety and regulatory requirements in the markets where it is sold. Users are advised to consult local regulations for specific compliance details relevant to their region and application.
11. Product Video
Watch a brief overview of the eletechsup DDIS24QC DIN Rail Isolated DC-DC Buck Converter:
Video 1: Product demonstration of the DDIS24QC converter.