RACBOX M8 Universal Aluminium Mini Motorcycle LED Turn Signal Indicator Lights

Contents

RACBOX M8 Universal Motorcycle LED Turn Signal Indicator Lights User Manual

1. Product Information

This manual provides essential information for the safe and effective use of your RACBOX M8 Universal Motorcycle LED Turn Signal Indicator Lights.

  • Product Name: Motorcycle Signal Lamp
  • Model: Motorcycle Signal Lamp
  • Batch/Serial Number: 020-07

2. Safety & Warnings

Please read all instructions carefully before use. Failure to follow these instructions may result in product damage or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.

3. Setup Instructions

Proper installation is crucial for the functionality and safety of your turn signal lights.

  1. Power Off First: Before beginning any installation, turn off your motorcycle's power switch and unplug the negative terminal of the battery. This prevents any potential short circuits during the process.
  2. Dismantling Old Lights: Carefully remove the original turn signal lights from your motorcycle. Disconnect or cut the corresponding wiring harness.
  3. Install New Lights: Align the fixed bracket of the new LED turn signal lights with the original mounting hole on your motorcycle. Securely tighten the turn signal screw.
  4. Wiring: Connect the wires of the new turn signals to the corresponding wires from your motorcycle's harness. Ensure that wires of the same color are connected. It is critical to ensure proper insulation and waterproofing for all connections to prevent electrical issues and damage from moisture. Note that LED lights often require dedicated flashers (relays) to operate correctly and prevent hyper-flashing.
Wiring diagram for RACBOX LED turn signals

Figure 1: Wiring Diagram - Shows two wires: Yellow light (positive) and Negative. Wire length is approximately 270mm.

  1. Testing Function: Once wired, reconnect the battery. Test both the left and right turn signals to confirm they flash normally. If a light does not turn on, reverse the plug polarity and retest.
  2. Final Assembly: After confirming proper operation, carefully reinstall any removed casings or covers.

4. Operating Instructions

These LED turn signal lights function as standard motorcycle indicators, providing amber flashing light to signal turns or lane changes. They are designed for high brightness without being dazzling.

Amber light effect of RACBOX LED turn signals

Figure 2: Light Effect - High brightness amber LED light beads, bright but not dazzling.

Video 1: Product Overview - A short demonstration of the RACBOX LED turn signals, showing their design and light output.

5. Maintenance

To ensure the longevity and optimal performance of your LED turn signal lights, follow these simple maintenance guidelines:

  • Cleaning: Regularly wipe the lights with a soft, damp cloth to remove dirt and grime. Avoid using abrasive cleaners or solvents that could damage the housing or lens.
  • Wiring Inspection: Periodically check the wiring connections for any signs of wear, corrosion, or damage. Ensure all connections remain secure and insulated.
  • Waterproofing: The lights are rated IP67 waterproof, meaning they are protected against dust and can withstand immersion in water up to 1 meter for 30 minutes. However, avoid prolonged submersion or high-pressure water jets directly on the lights.
IP67 Waterproof rating for RACBOX LED turn signals

Figure 3: Waterproof Rating - IP67 rating ensures bulbs keep working under different circumstances including rain, fog, sleet, and snow.

6. Troubleshooting

If you encounter issues with your turn signal lights, try the following solutions:

  • Light Not Turning On: If a light fails to illuminate after installation, first check the wiring connections. If connections are secure, try reversing the plug polarity. LEDs are polarity-sensitive and will only work when connected correctly.
  • Hyper-Flashing (Flashing Too Fast): This is common when replacing incandescent bulbs with LEDs. It indicates that the motorcycle's flasher relay detects lower resistance from the LEDs. You will need to install an LED-compatible flasher relay or load resistors (not included) to correct the flash rate.
  • Intermittent Operation: Check all wiring connections for looseness or corrosion. Ensure proper insulation to prevent short circuits.

7. Specifications

Detailed specifications for the RACBOX M8 Universal Motorcycle LED Turn Signal Indicator Lights:

FeatureSpecification
Voltage12V
MaterialAluminium
Bulb TypeLED
Mounting Bolt Thread8mm
Housing Color OptionsBlack, Chrome
Light ColorAmber
WiringTwo Wire (Yellow light, Negative)
Wire Length270mm
Dimensions (Length)42mm
Dimensions (Top Width)11mm
Dimensions (Base Width)15.5mm
Mounting Thread Length15mm
Waterproof RatingIP67
FitmentMost Motorcycle, Dirt Bike, Street Bike, Dual Sport Applications
Product size diagram for RACBOX LED turn signals

Figure 4: Product Size Diagram - Detailed dimensions of the turn signal lights.

8. User Tips

  • Always ensure your motorcycle's battery is disconnected before performing any electrical work.
  • For a clean and secure installation, use heat-shrink tubing over wire connections to enhance waterproofing and prevent corrosion.
  • Check local regulations regarding turn signal brightness and visibility requirements to ensure compliance.

9. Warranty & Support

This product is an auxiliary accessory for motorcycle lighting, intended for normal replacement and upgrade of original lights. It meets relevant national automotive lighting industry standards and has undergone strict quality testing.

Manufacturer Information:

  • Company: Guangzhou Bai Ji Tun Trading Co., Ltd
  • Address: C116, No. 1489, Fanghua Road Baiyun, Guangzhou
  • Email: tdlaccount@126.com

EU Authorized Representative:

  • Company: APEX CE SPECIALISTS LIMITED
  • Address: UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND
  • Email: info@apex-ce.com
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.