Yovanxer DQ-FSBSP092

Contents

Yovanxer 92 Inch PET Crystal Fixed Frame Projector Screen User Manual

Model: DQ-FSBSP092

Brand: Yovanxer

Introduction

Thank you for choosing the Yovanxer 92 Inch PET Crystal Fixed Frame Projector Screen. For optimal use and to ensure the longevity of your product, please read and keep this manual carefully before installation and use.

Every screen undergoes special quality checks. The manufacturer records a video of each screen produced in the factory to document its condition as it leaves the factory. We recommend that you also record a video for documentation when unpacking the screen. This will facilitate the manufacturer in processing any service requests in case of issues. Damage that occurs during the installation cannot be claimed. Therefore, please be extremely careful as the screen material is very fragile, and avoid folding or denting it.

Safety Precautions

To ensure the projection effect and quality of this product, please observe the following operating requirements:

  • When assembling, find a suitable size floor or table. The surface must be clean and free of any obstacles. The floor or table must be covered with clean materials such as cloth, film, blankets, etc.
  • Handle with care during installation to prevent personal injury or property damage.
  • Do not touch the surface of the projection screen with your hands.
  • Do not touch the projection surface with sharp or hard objects to prevent damage to the screen material. Do not write or draw on the screen.
  • Keep children away from the screen to prevent accidents.
  • The surface of the screen must be cleaned and treated regularly, and it is recommended to take care of it once every two weeks. Please use a soft cotton cloth to gently wipe (dip some water), and it is not advisable to use any chemical cleaners or alcohol.
  • If it is an ultra-short throw ambient light rejecting screen, please cooperate with two people during assembly, avoid screen folding or hard object friction impact action.

Parts List

Before beginning assembly, please ensure all parts are present and accounted for:

PartQuantity
Inner frame6
Outside frame6
Corner connectors4 (two types)
Corner protectors4
Screen1
Fiberglass strip6
Support rod1
4mm hexagon wrench1
Pull hook1
Tension springN (variable)
Upper wall bracket2
Under wall bracket2
M5*5 pan head screws16
Gloves2
User manual1
Wall bracket screws8
M4*8 screws16
Level ruler1
Diagram of all parts included in the package
Figure 1: Overview of all included parts.

Assembly Instructions

1. Frame Assembly

  1. Open the packaging box and categorize and arrange the components properly, cross-referencing the quantities with the "1.0 Parts" checklist.
  2. The horizontal frame is a segmented splicing type. The two horizontal inner frames are spliced correspondingly as shown in the figure. Note: There is a mark in the middle of the splicing strip of the inner frame, and the splicing position must be guaranteed to be at the mark.
  3. First, insert the four corner connectors into the vertical inner frame, as shown in the diagram.
  4. Assemble the horizontal and vertical inner frames according to the diagram. After completing the assembly of the inner frames, secure the corners with M5x5 screws, and then install the support rods.

Tip: Put all the screws on first, align them, and then tighten them one by one.

Diagram showing the assembly of the inner frame and support rods
Figure 2: Inner frame and support rod assembly.

2. Screen Assembly

  1. Wear gloves (to avoid fingerprints on the screen that cannot be erased). Lay a clean cloth on a flat, clean level countertop (or floor) that won't hurt the screen.
  2. Take out the screen from the package, put the screen face down, to unfold the curtain roll, spread it flat on the cloth on the table, and then insert the glass fiber strips into the around the screen according to the length as shown below.

Tip: All fiberglass strips extend out the same length at both ends of the screen.

Diagram showing screen unfolding and fiberglass strip insertion
Figure 3: Screen unfolding and fiberglass strip insertion.
  1. Place the assembled border on the screen. Note: The ultra-short focus anti-light screen has an up-and-down direction (other curtains have no direction). If it is an anti-light screen, it should be matched with the direction of the frame. Adjust the position of the screen according to the lines marked on the four corners of the screen.
  2. Hook the screen on the frame with a tension spring. To hook the tension spring, please follow the following sequence: first, hook 1~8 springs; then hook springs 9~12, and then hook other springs from the middle spring to both sides in turn. Please refer to the attached drawing for the installation method of the tension spring.
Diagram showing screen tension spring installation sequence
Figure 4: Screen tension spring installation.
  1. After hanging the spring, stand the screen up and check the overall flatness of the screen. If there is unevenness, the spring needs to be adjusted locally until it is level.
  2. Restore the screen to the position of step 2, ready to install the outer frame.

3. Outside Frame Installation

  1. Place the outer frame against the frame screen, align the four corners, and lock the inner and outer frames with M4×8 screws. Note: If there is a LOGO on the frame, it should be installed at the bottom of the screen.
  2. Adjust the outer frame at the corner to the smallest gap, and then tighten the screws. Lock the corners one by one according to this method, and finally deal with the splicing of the horizontal outer frame (if the gap is found to be too large, you can push the left and right outer frames inward).
  3. Finally, put the corner protectors on the four corners of the frame.
Diagram showing the assembly of the outside frame
Figure 5: Outside frame assembly.

Installation Instructions

  1. First, confirm the upper and lower wall bracket and their installation direction.
  2. Install wall hangers on the wall according to the screen size. Required tools include a level, hammer drill, pencil, and ladder. The horizontal distance between the wall brackets should be approximately 30cm from both sides of the screen. Estimate the installation position of the screen before installing the wall pendants. The height of the lower edge of the screen from the ground is generally about 600-800mm.
Diagram showing wall bracket installation measurements
Figure 6: Wall bracket installation measurements.
  1. Hang the screen on the wall according to the method shown in the picture.
Diagram showing how to hang the screen on the wall brackets
Figure 7: Hanging the screen on the wall.

Operating Instructions: Care & Cleaning

The surface of the screen must be cleaned and treated regularly, and it is recommended to take care of it once every two weeks. Please use a soft cotton cloth to gently wipe (dip some water), and it is not advisable to use any chemical cleaners or alcohol.

Troubleshooting

If you encounter any issues during assembly, installation, or operation that are not covered in this manual, please contact customer support for assistance. Ensure you have followed all steps carefully, especially regarding screen handling, to prevent damage.

Specifications

FeatureDetail
Model NumberDQ-FSBSP092
Brand NameYovanxer
MaterialPET Crystal
Format16:9
Screen TypeFrame Screen
Item NamePET Crystal Screen
Size92 inch
StyleUltra-thin border Fixed Frame
UsageFor cinema, training institutions, meeting rooms, home theater etc.
TypeALR UST projector Screen
CustomizableSupported
LED BacklightOptional
OEM/ODM/Drop shippingSupported
Viewing Angle160 degree
Suitable forAll kinds of Ultra Short Throw Projectors
Not suitable forTricolor laser projector
Warranty2 Years
OriginMainland China
Package Length154 cm
Package Width24 cm
Package Height15 cm
Package Weight13.2 kg

User Tips

  • This screen is an excellent choice for ultra-short throw projectors, designed to enhance your viewing experience.
  • The PET Crystal material provides clear visibility even with ambient light, reducing the need for a dark room.
  • The screen is compatible with 3D, 4K, 8K, and HD content, offering versatile high-quality projection.
  • With a gain of 0.8 (Brightness) and 2.5 (Contrast), it optimizes image quality for a vibrant display.
  • The wide 160-degree viewing angle ensures a great picture from various positions in the room.
Video: Demonstrates the superior image quality and ambient light rejection of the PET Crystal screen compared to a white wall, even in a lit room.

Warranty & Support

This product comes with a 2-year warranty from the date of purchase.

For any technical support, inquiries, or warranty claims, please contact:

  • Service Hotline: 008618621934178
  • Email: sales@dqprojection.com

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.