1. Safety Information
The NJTY T28B Digital Multimeter conforms to IEC61010-1 CAT III 600V, 1000V CAT II IEC61010 and pollution level II. A Warning identifies conditions and procedures that are dangerous to the user. To prevent possible electrical shock, fire, or personal injury:
- Do not alter the Product and use only as specified, or the protection supplied by the Product can be compromised.
- Do not use the Product around explosive gas, vapor, or in damp or wet environments.
- Do not operate the Product with covers removed or the case open. Hazardous voltage exposure is possible.
- Do not apply more than the rated voltage, between the terminals or between each terminal and earth ground.
- Do not use test leads if they are damaged. Examine the test leads for damaged insulation, exposed metal, or if the wear indicator shows. Check test lead continuity.
- Use the correct terminals, function, and range for measurements.
- The range switch should be placed in the correct range position.
- The input signal is not allowed to exceed the specified limit value to prevent electric shock and damage to the instrument.
- When measuring televisions or switching power supplies, be aware that there may be pulses in the circuit that can damage the circuit.
- Remove the batteries if the Product is not used for an extended period of time, or if stored in temperatures above 50°C.
Safety Symbols
| Symbol | Description | Symbol | Description |
|---|---|---|---|
| ⚠ | WARNING. Risk of danger. | ≈ | AC or DC |
| ⚡ | High voltage warning | □ | Double insulated |
| — | DC (Direct Current) | ☒ | Fuse |
| ∼ | AC (Alternating Current) | ⟂ | Ground |
| CE | Conforms to European Union directives. | ||
| CAT. II | Measurement Category II is applicable to test and measuring circuits connected directly to utilization points (socket outlets and similar points) of the low-voltage MAINS installation. | ||
| CAT. III | Measurement Category III is applicable to test circuits connected to the distribution part of the building's low-voltage MAINS installation. | ||
2. Product Familiarization
The NJTY T28B Digital Multimeter is a versatile tool designed for various electrical measurements. Below is an overview of its components and functions.

Overview of Components
- Flashlight
- Alarm Indication Light
- NCV Sensor
- LCD Screen
- Function Switching & Lock Button
- Frequency/Duty Cycle / Capacitance ZERO Button
- Flashlight & Backlight Button
- Manual/Auto-ranging Switch
- mA Input Socket (MAX 600mA)
- 20A Input Socket (MAX 20A)
- VΩHzC Socket
- COM Socket
Backlight / Flashlight
- Push the '☀/🔦' button to toggle the backlight on and off.
- Press and hold this button for 2 seconds to turn on the flashlight and backlight at the same time. Press again to turn them off.
- The backlight / flashlight automatically turns off after 30 seconds.
Auto Power Off
- The Auto Power Off function is enabled by default at boot, indicated by the '⏻' symbol.
- Without any operation for about 15 minutes, the Meter will automatically turn off.
- To cancel auto power off, press and hold both 'FUNC HOLD' to turn on the meter.
Display HOLD
- In Display HOLD mode, the Meter freezes the display and 'H' shows on the display.
- Push the 'FUNC HOLD' button for 2 seconds to activate/deactivate Display HOLD.
- To avoid electric shock, when Display HOLD is activated, be aware that the display will not change.
3. Setup
Battery Installation
The NJTY T28B Multimeter requires 4 x 1.5V AAA batteries (not included). Follow these steps to install or replace batteries:
- Turn off the meter.
- Pull out all test leads from the input sockets.
- Use a screwdriver to loosen the screws securing the battery cover or back cover.
- Remove the battery cover or back cover.
- Remove the old battery or damaged fuse.
- Replace with new 4 X 1.5V AAA batteries. Ensure correct polarity.
- Install the battery cover or back cover, and tighten the screws.
4. Operating Instructions
Manual and Auto-ranging
- The Meter defaults to Auto-range ('AUTO' on display).
- Short-push 'RANGE' button to enter Manual range. Push 'RANGE' to increment range.
- Push 'RANGE' button for 2 seconds to enter Auto-range mode.
DC/AC Voltage Measurement
- Connect the black test lead to the 'COM' port and the red test lead to the 'VΩHzC' port.
- Switch to the '∼mV' or '∼V' ranges. 'DC' signal indicates DC voltage test. Press 'FUNC HOLD' for ACV test ('AC' on screen).
- Connect the test leads to the loaded circuit.
Note:
- Do not measure voltage above DC1000V or AC750V to prevent damage.
- For AC/DC 600mV and AC 6V ranges, if the meter displays numbers without input, short-circuit the 'VΩHzC' and 'COM' ports. If it returns to zero, the meter is normal.


Resistance Measurement
- Connect the black test lead to the 'COM' port and the red test lead to the 'VΩHzC' port.
- Switch to the 'Ω' range (Ω shows on display).
- Connect the test leads to the resistor to be tested.
Note:
- 'OL' indicates overload; switch to a higher range. 'OL' also appears if open-circuited.
- If the resistor is > 60MΩ, it may take a few seconds to read.
- Before testing, ensure the circuit is powered off and high-voltage capacitors are discharged.
- For low resistance, short-circuit test leads, read value, then subtract from measured resistance.
Diode Measurement
- Connect the black test lead to the 'COM' port and the red test lead to the 'VΩHzC' port.
- Switch to the '→|—' and press 'FUNC HOLD' button 2 times (→|— shows on display).
- Touch the diode anode with the red probe, and the cathode with the black probe.
Note:
- 'OL' will be displayed if open-circuited or if test leads are connected with reverse polarity.
- A normal diode in circuit will show a forward voltage drop of 0.5V to 0.8V.
Continuity Measurement
- Connect the black test lead to the 'COM' port and the red test lead to the 'VΩHzC' port.
- Switch to the '♫' and press 'FUNC HOLD' button (♫ shows on display).
- Contact the probes to the circuit or resistance.
- The Meter will buzz and show a yellow light if resistance is < 40Ω. For 40Ω to 60Ω, no buzz, red light.
Note:
- Before testing, ensure the circuit is powered off and high-voltage capacitors are discharged.
Capacitance Measurement
- Connect the black test lead to the 'COM' port and the red test lead to the 'VΩHzC' port.
- Switch to the '—||—' range and connect the test leads to the circuit.
Note:
- Before testing, ensure the circuit is powered off and high-voltage capacitors are discharged.
- Large capacitance may take longer to stabilize readings.
- Observe capacitor polarities for correct connection and meter protection.
Frequency/Duty Cycle Measurement
- Connect the black test lead to the 'COM' port and the red test lead to the 'VΩHzC' port.
- Switch to the 'Hz%' and use the 'Hz% / △' button to select Frequency or Duty Ratio.
- Connect the test leads to the circuit.
Note:
- Do not test any voltage higher than 250V to prevent electric shock or damage.
DC/AC Current Measurement
- Connect the black test lead to 'COM'. For current < 600mA, connect red lead to 'mA' port. For current 600mA-20A, connect red lead to '20A' port.
- Switch to the 'μA', 'mA', or 'A' ranges. 'DC' signal indicates DC current test. Press 'FUNC HOLD' for AC current test ('AC' on screen).
- Disconnect the circuit to be tested. Connect the black test pen to the lower voltage end and the red test pen to the higher voltage end of the disconnected circuit. Then connect the test leads to the loaded circuit.
Note:
- 'OL' indicates overload; switch to a higher range.
- Do not attempt current measurement if voltage between open circuit and ground exceeds 250V. Check fuse integrity before measurement. Turn off power to circuit before connecting.
- Pay special attention to safety when measuring high voltage.
- Test with a known current before use.
NCV (Non-Contact Voltage) Test
- Turn the knob to 'NCV'.
- Gradually approach the detected point with the NCV probe.
- Weak AC signals: yellow indicator lights up, slow beeps.
- Strong AC signals: red indicator lights up, quick beeps.
Note:
- Do not rely solely on NCV detectors to confirm voltage presence, as factors like socket depth, insulation thickness, etc., can affect readings.
- Induced voltage may cause the indicator to light up.
- External interference (flashlights, motors) may trigger NCV detection.
Temperature Measurement
- Turn the knob to '°C' (meter displays ambient temperature).
- Switch between '°C' or '°F' using the 'FUNC HOLD' button.
- Insert the thermocouple: positive (red) into 'VΩHzC' input, negative (black) into 'COM' input.
- Contact the measured object with the thermocouple probe. Do not touch charged objects with the thermocouple probe.

5. Specifications
| Feature | Detail |
|---|---|
| Operating conditions | 600V CAT.III and 1000V CAT.II |
| Maxim Display | 6000 counts |
| Pollution grade | II |
| Biggest voltage between measurement end and ground | 1000VDC or 750VAC |
| Conversion rate | About 3 Times/Second |
| Height | Under 2000m |
| Operation Temperature | 0°C - 40°C (<80%RH, not considered <10°C) |
| Storage Temperature | -10°C - 60°C (<70%RH, batteries removed) |
| Battery Type | 4 * 1.5V AAA Batteries |
| Fuse | F 600mA/250V, F 20A/250V |
| Overload display | 'OL' displayed |
| Input polarity indicator | '-' shown automatically |
| Dimensions | 195mm (L)*92mm (W)*52mm (H) |
| Weight | About 397g (battery included) |
AC Voltage
| Range | Resolution | Accuracy |
|---|---|---|
| 600mV | 0.1mV | |
| 6V | 1mV | ± (1%+4) |
| 60V | 10mV | |
| 600V | 100mV | |
| 750V | 1V | ± (1.2%+4) |
| Input Impedance: 10MΩ | ||
| Maximum input voltage: 1000VDC or 750VAC RMS | ||
| Frequency Response: 40Hz~1KHz; T-RMS | ||
DC Voltage
| Range | Resolution | Accuracy |
|---|---|---|
| 600mV | 0.1mV | |
| 6V | 1mV | ± (0.5%+5) |
| 60V | 10mV | |
| 600V | 100mV | |
| 1000V | 1V | ± (0.8%+5) |
| Input Impedance: 10MΩ | ||
| Maximum input voltage: 1000VDC or 750VAC RMS | ||
AC Current
| Range | Resolution | Accuracy |
|---|---|---|
| 600μA | 0.1μA | |
| 60mA | 0.01mA | ± (1.5%+5) |
| 600mA | 0.1mA | |
| 20A | 10mA | ± (2.0%+5) |
| Overload protection: mA range with F600mA/250V and 20A range with F20A/250V | ||
| Max input current: mA: 600mA RMS, 20A: 20A RMS | ||
| When current > 5A, test time < 10 minutes. Allow 1 minute rest after such measurement. | ||
| Frequency response: 40HZ to 1KHZ T-RMS | ||
DC Current
| Range | Resolution | Accuracy |
|---|---|---|
| 600μA | 0.1μA | |
| 60mA | 0.01mA | ± (1.2%+5) |
| 600mA | 0.1mA | |
| 20A | 10mA | ± (2.0%+5) |
| Overload protection: mA range with F600mA/250V and 20A range with F20A/250V | ||
| Max input current: mA: 600mA RMS, 20A: 20A RMS | ||
| When current > 5A, test time < 10 minutes. Allow 1 minute rest after such measurement. | ||
| Frequency response: 40HZ to 1KHZ T-RMS | ||
Frequency
| Range | Resolution | Accuracy |
|---|---|---|
| 9.999Hz | 0.001Hz | |
| 99.99Hz | 0.01Hz | |
| 999.9Hz | 0.1Hz | ± (1.5%+5) |
| 9.999KHz | 0.001KHz | Input voltage range: 200mV - 10V AC RMS Overload protection: 250V DC/AC |
| 99.99KHz | 0.01KHz | |
| 999.9KHz | 0.1KHz | |
| 9.999MHz | 0.001MHz |
Capacitance
| Range | Resolution | Accuracy |
|---|---|---|
| 6nF | 0.001nF | |
| 60nF | 0.01nF | |
| 600nF | 0.1nF | ± (4.0%+5) |
| 6μF | 1nF | |
| 60μF | 10nF | |
| 600μF | 100nF | |
| 6mF | 1μF | ± (5.0%+5) |
| 100mF | 10μF | |
| Overload protection: 250V DC/AC | ||
Resistance
| Range | Resolution | Accuracy |
|---|---|---|
| 600Ω | 0.1Ω | |
| 6KΩ | 1Ω | |
| 60KΩ | 10Ω | ± (0.8%+5) |
| 600KΩ | 100Ω | |
| 6MΩ | 1KΩ | |
| 60MΩ | 10KΩ | ± (1.2%+5) |
| Open circuit voltage: 2.4V | ||
| Overload protection: 250V DC/AC | ||
Diode / Continuity
| Function | Range | Resolution | Detail |
|---|---|---|---|
| →|— | 0-3V | 0.001V | Forward direct current: about 1mA. OCV about 3.2V |
| ♫ | 600Ω | 0.1Ω | Resistor<40Ω, buzz with yellow light. 40Ω<resistor<60Ω, buzz with red light. OCV about 1V |
Temperature
| Range | Resolution | Temperature | Accuracy |
|---|---|---|---|
| °C | 1°C | -20°C ~ 1000°C | ± (1.0%+3) |
| °F | 1°F | -4°F ~ 1832°F | ± (1.0%+3) |
6. Maintenance
General Maintenance
- Check the battery first; if '⏻' is displayed, the battery needs to be changed.
- Only use the specified fuse (600mA / 250V, 20A / 250V fast melt fuse) to avoid electric shock or personal injury.
- Turn off and check that the test has been disconnected from the measured circuit before opening the battery cover and replacing the new battery.
Cleaning
- Turn off the power to the Meter and remove the test leads.
- Wipe the case with a damp cloth and mild detergent.
- Dirt or moisture in the terminals can affect readings.
- If there is any abnormality, stop using the meter immediately.
Install Batteries & Replace Fuses
- Turn off the meter.
- Pull out all test leads from the input sockets.
- Use a screwdriver to loosen the screws securing the battery cover or back cover.
- Remove the battery cover or back cover.
- Remove the old battery or damaged fuse.
- Replace with new 4 X 1.5V AAA batteries or new fuse.
- Install the battery cover or back cover, and tighten the screws.
7. Troubleshooting
This section provides guidance for common issues you might encounter with your NJTY T28B Digital Multimeter.
- "OL" Displayed: This indicates an overload condition or an open circuit. Ensure the measurement range is appropriate for the value being measured. If measuring resistance, check for open circuits.
- No Display / Meter Not Turning On: Check battery installation and ensure batteries are fresh. If the low battery indicator (⏻) was displayed, replace the batteries.
- Inaccurate Readings: Ensure test leads are not damaged and are correctly connected. Verify the correct function and range are selected. Clean terminals if dirty or moist.
- No NCV Detection / False NCV Detection: Be aware that NCV can be affected by external factors like socket depth, insulation thickness, or nearby interference sources (e.g., flashlights, motors).
- No Continuity Buzz / Incorrect Light: Check if the circuit is powered off and capacitors are discharged. Verify resistance values as per specifications (yellow light for <40Ω, red light for 40-60Ω).
8. User Tips
- Amperage Measurement: The multimeter works well for measuring amperage up to 20A. Users have confirmed successful tests for 10A in DC.
- Initial Check: Always verify the multimeter's functionality upon receipt. One user reported an incomplete battery box, preventing power-on. Ensure all parts are present and batteries can be installed correctly.
- General Performance: Many users find the product in perfect condition and working correctly, describing it as a "very good multimeter."
9. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official product documentation or contact the seller directly. Keep your purchase receipt as proof of purchase.
A user manual in PDF format is available for download: View User Manual (PDF).