WESA EP-09-RED

Contents

WESA Wall Socket and Switch Instruction Manual

Model: EP-09-RED Series

1. Product Overview

The WESA EP-09-RED series offers a range of wall-embedded electrical devices, including power sockets, light switches, and USB charging outlets. These products are designed for residential and general-purpose applications, featuring high-temperature flame-retardant plastic material for enhanced safety and durability. They comply with CE, RoHS, and WEEE certifications.

2. Safety Information

  • Always disconnect power at the main circuit breaker before installation, maintenance, or any work involving electrical wiring.
  • Installation should be performed by a qualified electrician or a competent person familiar with electrical wiring practices.
  • Do not exceed the rated current and voltage of the device.
  • Ensure proper grounding where applicable to prevent electric shock.
  • Do not use the product if it appears damaged.

3. Setup and Installation

3.1 Tools Required

  • Screwdriver (Phillips and/or Flathead)
  • Wire Strippers
  • Voltage Tester

3.2 Product Dimensions

Ensure your wall box is compatible with the standard 83x83mm dimensions of the device.

Product dimensions diagram showing front, back, and side views with measurements in mm and inches.

Figure 1: Product Dimensions (83mm x 83mm front plate)

3.3 Wiring Instructions

Follow the specific wiring diagram for your product type. Always ensure wires are securely connected and insulated.

3.3.1 1-Gang and 2-Gang 1-Way Switches

Wiring diagram for 1-gang and 2-gang 1-way switches. Shows Neutral (N), Live (L), and three switched Live lines (L1, L2, L3) connected to light fixtures.

Figure 2: Wiring for 1-Gang and 2-Gang 1-Way Switches. Connect Neutral (N) and Live (L) to the switch module. L1, L2, L3 connect to the respective light loads.

3.3.2 1-Socket (Not Grounded)

Wiring diagram for a 1-socket without ground. Shows Neutral (N) and Live (L) connections.

Figure 3: Wiring for 1-Socket (Not Grounded). Connect Neutral (N) and Live (L) to the corresponding terminals.

3.3.3 1-Socket (With Ground)

Wiring diagram for a 1-socket with ground. Shows Neutral (N), Live (L), and Earth (E) connections.

Figure 4: Wiring for 1-Socket (With Ground). Connect Neutral (N), Live (L), and Earth (E) to the corresponding terminals.

3.3.4 1-Socket and 2-USB Ports

Wiring diagram for a 1-socket with 2 USB ports. Shows Earth (E), Live (L), and Neutral (N) connections.

Figure 5: Wiring for 1-Socket and 2-USB Ports. Connect Earth (E), Live (L), and Neutral (N) to the corresponding terminals.

3.3.5 1-Socket (France Standard)

Wiring diagram for a 1-socket France standard. Shows Neutral (N), Live (L), and Earth (E) connections.

Figure 6: Wiring for 1-Socket (France Standard). Connect Neutral (N), Live (L), and Earth (E) to the corresponding terminals.

3.4 Installation Steps

  1. Turn off Power: Locate the circuit breaker controlling the area where you will install the device and turn it off. Verify with a voltage tester that the power is off.
  2. Prepare Wires: Strip approximately 10-12mm of insulation from the ends of the electrical wires (Live, Neutral, Earth).
  3. Connect Wires: Following the appropriate wiring diagram (Figures 2-6), connect the wires to the terminals on the back of the device. Ensure all connections are tight and secure.
  4. Mount Device: Carefully push the wired device into the wall box. Secure it using the mounting screws provided.
  5. Attach Faceplate: Snap or screw the decorative faceplate onto the device.
  6. Restore Power: Turn the power back on at the circuit breaker.
  7. Test: Test the functionality of the socket, switch, or USB ports.

4. Operating Instructions

  • For Sockets: Insert the plug of your appliance into the socket. Ensure the appliance's power requirements do not exceed the socket's rated capacity (16A, 220V).
  • For Switches: Press the switch rocker to turn connected lights or appliances ON or OFF.
  • For USB Ports: Connect your USB charging cable to the USB port and then to your device. The USB ports provide power for charging compatible devices.

5. Maintenance

  • Cleaning: To clean the surface, wipe with a soft, slightly damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish.
  • Inspection: Periodically inspect the device for any signs of damage, such as cracks, discoloration, or loose connections. If any damage is found, disconnect power and replace the device.
  • Ensure the device remains free from dust and debris.

6. Troubleshooting

  • No Power to Socket/USB:
    • Check your main circuit breaker to ensure it has not tripped.
    • Verify that the wiring connections are secure (ensure power is off before checking).
    • Test the outlet with a known working appliance.
  • Switch Not Operating:
    • Check the light bulb or appliance connected to the switch.
    • Verify wiring connections to the switch (ensure power is off before checking).
  • USB Not Charging:
    • Ensure your USB cable is functional and properly connected.
    • Confirm your device is compatible with standard USB charging.

If problems persist after troubleshooting, consult a qualified electrician.

7. Specifications

FeatureSpecification
Brand NameWESA
Model NumberEP-09-RED
MaterialPlastic (Flame Retardant)
Rated Current16A
Socket TypeSocket 220V
Installation TypeWall Embedded
Standard Size83*83mm
GroundingStandard Grounding (where applicable)
ApplicationResidential / General-Purpose
CertificationCE, RoHS, WEEE
Backlight/IndicationNot applicable

8. User Tips

  • Always ensure the power is off at the circuit breaker before performing any installation or inspection.
  • Use a voltage tester to confirm that circuits are de-energized before touching any wires.
  • Do not overload electrical circuits. Be mindful of the total wattage of devices plugged into a single circuit.
  • For optimal safety, ensure all grounding wires are correctly connected for devices that require it.

9. Warranty and Support

WESA products are manufactured to high-quality standards. For warranty information and support, please refer to the official product documentation or contact your retailer. A detailed user manual in PDF format may be available for download from the manufacturer's website or via the provided link: User Manual (PDF).

© 2024 WESA. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.