Introduction
This manual provides detailed instructions for the operation and maintenance of your Casio AE-1200WHD-1A digital watch. Please read this guide thoroughly to ensure proper use and to take full advantage of its features. The operational procedures for Modules 3198 and 3299 are identical, and this manual covers both.

Watch Components and Button Functions
Your watch features four buttons, each with specific functions:
- Button A (ADJUST): Used for entering and exiting setting screens, and confirming selections.
- Button B (MODE): Cycles through the watch's various modes.
- Button C (WORLD TIME): Used for scrolling eastwardly in World Time mode and for increasing values during settings.
- Button D (LIGHT / SEARCH): Activates illumination and is used for decreasing values during settings.

Initial Setup: Time and Date Settings
To set the current Home City Time and Date:
- In Timekeeping Mode, ensure the current Home City Time (T-1) screen is displayed.
- Hold down Button A (ADJUST) until the seconds start to flash, indicating the setting screen.
- Press Button B (MODE) to cycle through the settings in the following sequence: Seconds → DST → City Code → Hour → Minutes → 12/24-Hour Format → Year → Month → Day → Illumination Duration.
- While the desired setting is flashing, use Button C (WORLD TIME) to increase the value or Button D (LIGHT / SEARCH) to decrease it.
- To toggle between Daylight Saving Time (DST) and Standard Time, press Button D (LIGHT / SEARCH) when the DST setting is flashing.
- Once all settings are correct, press Button A (ADJUST) to exit the setting screen.
The day of the week is automatically displayed based on the date settings.
Operating Modes
Press Button B (MODE) to cycle through the watch's modes in the following order: Timekeeping Mode → World Time Mode → Alarm Mode → Countdown Timer Mode → Stopwatch Mode.
Timekeeping Mode
This mode displays the current time and date for your Home City (T-1) and three Local Times (T-2, T-3, T-4). The digital dial at the top of the screen indicates the current Home City Time (T-1).
To switch between time screens (T-1, T-2, T-3, T-4), press Button D (LIGHT / SEARCH).
World Time Mode
The watch displays the current time in 48 cities (31 time zones) around the world. To enter World Time Mode, press Button B (MODE) until 'WT' appears on the display.
To view the time for another city code, press Button C (WORLD TIME) to scroll eastwardly through city codes.
To toggle between Standard Time and Daylight Saving Time (DST) for a displayed city code: Hold down Button A (ADJUST) for about one second. The DST indicator will appear when DST is active.
Alarm Mode
Your watch has five independent alarms (one-time or daily) and an Hourly Time Signal.
To set an alarm:
- In Alarm Mode, use Button C (WORLD TIME) to scroll through the alarm screens (AL1, AL2, AL3, AL4, AL5, SNZ, SIG) until the desired alarm number is displayed.
- Hold down Button A (ADJUST) until the hour setting starts to flash.
- Press Button B (MODE) to move between hour, minutes, and alarm type (one-time/daily).
- Use Button C (WORLD TIME) and Button D (LIGHT / SEARCH) to change the flashing item.
- Press Button A (ADJUST) to exit.
To turn an alarm on/off: In Alarm Mode, select the alarm, then press Button A (ADJUST) to toggle it on or off.
To turn the Hourly Time Signal on/off: In Alarm Mode, select 'SIG', then press Button A (ADJUST) to toggle it on or off.
Countdown Timer Mode
The countdown timer can be set from one second up to 24 hours. An alarm sounds when the countdown reaches zero.
To configure the countdown timer:
- In Countdown Timer Mode, hold down Button A (ADJUST) until the current countdown start time starts to flash.
- Press Button B (MODE) to move between hours, minutes, and seconds.
- Use Button C (WORLD TIME) and Button D (LIGHT / SEARCH) to change the flashing item.
- Press Button A (ADJUST) to exit.
To use the countdown timer: Press Button D (LIGHT / SEARCH) to start, pause, and resume the countdown. To stop completely, pause it then press Button A (ADJUST).
Stopwatch Mode
The stopwatch measures elapsed time, split times, and two finishes, with a capacity of 23 hours, 59 minutes, 59.99 seconds.
To measure times:
- Elapsed Time: Press Button D (LIGHT / SEARCH) to Start, Stop, and Re-start. Press Button A (ADJUST) to Clear.
- Split Time: Press Button D (LIGHT / SEARCH) to Start. Press Button A (ADJUST) for Split (display freezes). Press Button A (ADJUST) again for Split Release. Press Button D (LIGHT / SEARCH) to Stop. Press Button A (ADJUST) to Clear.
- Two Finishes: Press Button D (LIGHT / SEARCH) to Start. Press Button A (ADJUST) when the first runner finishes (display freezes). Press Button D (LIGHT / SEARCH) when the second runner finishes. Press Button A (ADJUST) to display the first runner's time, then Button A (ADJUST) again to display the second runner's time. Press Button A (ADJUST) to Clear.
Illumination
The watch features an LED (light-emitting diode) for display illumination, making it easy to read in the dark.
To turn on illumination: In any mode (except when a setting screen is on), press Button D (LIGHT / SEARCH).
You can select an illumination duration of either 1.5 seconds or 3 seconds in the time setting screen (see Initial Setup). The illumination will remain on for the selected duration.
Illumination Precautions:
- Illumination may be difficult to see under direct sunlight.
- Illumination automatically turns off when an alarm sounds.
- Frequent use of illumination can reduce battery life.

Care and Maintenance
Water Resistance
Your watch is water resistant up to 10 Bar (100 meters). This means it is suitable for swimming and snorkeling, but not for scuba diving. Do not operate buttons while the watch is wet or submerged.
Battery Replacement
The watch uses one lithium battery (Type: CR2025) with an approximate 10-year battery life. When the display becomes dim or functions become erratic, it's time to replace the battery. Battery replacement should ideally be performed by a qualified technician to ensure water resistance is maintained.
Cleaning and Storage
- Wipe the watch with a soft, dry cloth to remove dirt and moisture.
- Avoid exposing the watch to extreme temperatures, direct sunlight for prolonged periods, or strong magnetic fields.
- Store the watch in a dry place when not in use.


Troubleshooting
- Time is incorrect: Ensure your Home City Time and DST settings are correct. The watch's full auto-calendar accounts for month lengths and leap years, so manual date adjustment is rarely needed once set.
- Alarm not sounding: Check if the alarm is turned on in Alarm Mode. Also, ensure the battery is not depleted.
- Display is dim or blank: The battery may need replacement.
- Buttons are unresponsive: If the watch is wet, dry it thoroughly. If the issue persists, the battery might be low, or there could be an internal malfunction.
- Button operation tone is off: If the MUTE indicator is displayed, the button operation tone is turned off. Hold down Button B (MODE) to toggle it on/off.
User Tips
- Keep the Manual Handy: Initial configuration and less frequent adjustments can be complex. It's recommended to keep a digital copy of the manual on your phone for quick reference.
- Bracelet Adjustment: The stainless steel bracelet is often generously sized. It is possible to adjust the length by removing links at home with appropriate tools, or by visiting a jeweler for a professional fit.
- 10-Year Battery: The long-lasting battery is a significant advantage. When replacement is eventually needed, it is generally straightforward and economical.
Specifications
| Feature | Detail |
|---|---|
| Model Number | AE-1200WHD-1A |
| Brand | Casio |
| Item Type | Digital Wristwatch |
| Movement | Digital |
| Display Type | Digital |
| Case Material | Resin |
| Case Shape | Rectangle |
| Case Thickness | 13mm |
| Dial Diameter | 45mm |
| Dial Window Material Type | Resin |
| Band Material Type | Stainless Steel |
| Band Width | 20mm |
| Band Length | 20cm |
| Clasp Type | Bracelet Clasp |
| Water Resistance Depth | 10 Bar (100 meters) |
| Accuracy | ±30 seconds a month (at normal temperature) |
| Battery | One lithium battery (Type: CR2025) |
| Battery Life | Approx. 10 years |
| Features | Luminous, LED Display, Complete Calendar, Alarm, Week Display, World Time, Stopwatch, Countdown Timer |
| Origin | Japan (Movement), Made in China (Assembly) |

Frequently Asked Questions (FAQ)
- Q: Is this watch original?
- A: Yes, the Casio AE-1200WHD-1A is an authentic Casio product.
- Q: What is the case material, resin or stainless steel?
- A: The watch case is made of Resin, while the band is Stainless Steel.
- Q: Where is the watch made?
- A: While Casio is a Japanese brand, the AE-1200WHD-1A model is typically assembled in China, as indicated on the watch's back cover.
Warranty and Support
Your Casio watch comes with a manufacturer's warranty covering defects in materials and workmanship. For specific warranty details, including duration and coverage, please refer to the warranty card included with your purchase or visit the official Casio website for your region.
For technical support, service, or inquiries not covered in this manual, please contact Casio customer service or an authorized service center.
