1. Product Overview
The WESA MZB05 is a wall-mounted electrical outlet designed for EU standard plugs. It features a durable, flame-retardant plastic construction suitable for residential and general-purpose applications. This manual provides instructions for safe installation, operation, and maintenance.

Figure 1: WESA MZB05 2-socket EU wall outlet, front view.
2. Safety Information
- Always disconnect power at the main circuit breaker or fuse box before installing or servicing electrical outlets.
- Installation should only be performed by a qualified electrician in accordance with local electrical codes and regulations.
- Do not exceed the rated voltage (220V) or current (16A) of this device.
- This product is designed for indoor use or protected outdoor environments where it is not directly exposed to water or extreme weather conditions.
- Do not use if the product appears damaged.
- Keep away from children.
3. Setup and Installation
This outlet is designed for wall-mounted surface installation. Ensure the mounting surface is flat and stable.
3.1 Tools Required (Not Supplied)
- Screwdriver (appropriate for terminal and mounting screws)
- Wire strippers
- Voltage tester
- Drill (if mounting to a new surface)
- Wall plugs/anchors (if required for mounting surface)
3.2 Installation Steps
- Power Disconnection: Turn off the power to the circuit at the main electrical panel. Verify that the power is off using a voltage tester.
- Prepare Wires: Strip approximately 10-12mm of insulation from the ends of the live (brown/black) and neutral (blue) wires. This outlet is non-grounding, so a ground wire connection is not required for the outlet itself, but ensure any existing ground wire is safely terminated or insulated according to local codes.
- Connect Wires: Loosen the terminal screws on the back of the outlet. Insert the stripped live wire into the 'L' terminal and the neutral wire into the 'N' terminal. Tighten the screws securely to ensure good electrical contact.
- Mount the Outlet: Position the outlet on the desired wall surface. Mark the screw hole locations. Drill pilot holes if necessary. Secure the outlet to the wall using appropriate screws. Ensure the outlet is firmly attached and does not wobble.
- Final Check: Double-check all wire connections for tightness and ensure no bare wires are exposed.
- Restore Power: Turn the power back on at the main electrical panel.
- Test: Test the outlet with a known working appliance.

Figure 2: Dimensions of the WESA MZB05 outlet (Length: 103mm / 4.05in, Width: 62mm / 2.44in, Height: 33mm / 1.29in).
For detailed wiring diagrams or specific installation scenarios, please refer to the official user manual PDF: User Manual (PDF).
4. Operating Instructions
Once installed and power is restored, the WESA MZB05 outlet is ready for use.
- Ensure your appliance is compatible with EU standard plugs and operates within 220V and 16A specifications.
- Insert the appliance plug firmly into the socket.
- To disconnect, pull the plug directly out of the socket. Do not pull by the cord.
This outlet features a matte finish for a smooth texture and is designed to be anti-fouling and fingerprint-free.

Figure 3: Smooth texture and anti-fouling surface of the outlet.
5. Maintenance
- Cleaning: Disconnect power before cleaning. Wipe the surface with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as these can damage the finish or internal components.
- Inspection: Periodically inspect the outlet for any signs of damage, such as cracks, discoloration, or loose connections. If any damage is observed, disconnect power and have the outlet inspected or replaced by a qualified electrician.
- Environmental: Avoid exposing the outlet to direct sunlight for prolonged periods or extreme temperatures.
The outlet is constructed from high-temperature flame-retardant material to prevent fire hazards and features a durable design resistant to falling.

Figure 4: High-temperature flame-retardant material for safety.
6. Troubleshooting
6.1 No Power from Outlet
- Check Circuit Breaker: Verify that the circuit breaker for the outlet is in the "ON" position. If it has tripped, reset it.
- Check Connections: Ensure the wires are securely connected to the outlet terminals. (Power must be off before checking connections).
- Test Appliance: Try plugging in a different appliance to confirm the issue is with the outlet and not the original appliance.
6.2 Loose Fit After Installation
- Ensure the mounting surface is flat and even.
- Use appropriate screws and wall anchors (if needed) to secure the outlet firmly to the wall.
- Verify that the outlet's base is not warped or damaged, which could prevent a flush fit.
If problems persist, consult a qualified electrician.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | WESA |
| Model Number | MZB05 |
| Material | Plastic (Flame retardant ABS panel, Flame retardant plastic base) |
| Copper Material | High quality brass |
| Contact Material | Silver dots |
| Rated Current | 16A |
| Socket Type | Socket 220V (EU Standard) |
| Installation Type | Wall Mounted |
| Grounding | Non-Grounding |
| Application | Residential / General-Purpose |
| Number of Slots | 2 (for 2-socket variant) |
| Standard Dimensions | 104*64*32mm |
| Certification | CE, RoHS, WEEE |
| Origin | Mainland China |
| Is Smart Device | No |
| Backlight/Indication | Not applicable |
| Shape | Rectangular |
8. User Tips
- Secure Mounting: To ensure a stable and safe installation, always use appropriate fasteners for your wall type and ensure the outlet is mounted flush and securely. If the outlet feels loose, re-tighten mounting screws or use stronger anchors.
- Plug Insertion: Always ensure appliance plugs are fully inserted into the socket to prevent arcing and ensure a proper connection.
- Cleanliness: The matte finish is designed to resist fingerprints and stains, making it easy to keep clean with a simple dry wipe.
9. Warranty and Support
For warranty information, technical support, or any product-related inquiries, please contact your original point of purchase or the seller directly. Please have your model number (MZB05) and purchase details available when contacting support.
Additional information may be available in the comprehensive user manual PDF: User Manual (PDF).