1. Introduction
This manual provides essential information for the safe installation, operation, and maintenance of your new exterior door handles for Honda Civic EK3, EK4, and EK9 models manufactured between 1996 and 2000. Please read this manual thoroughly before installation to ensure proper fitment and functionality.
2. Safety Information & Warnings
Failure to follow these instructions may result in damage to the product or personal injury.
- Always wear appropriate personal protective equipment (PPE) such as safety glasses and gloves when handling tools and installing parts.
- Keep all tools and small components out of reach of children.
- Inspect the door handles for any signs of damage before installation. Do not proceed with installation if the product appears damaged.
- Handle the door handles and any sharp tools with care to prevent cuts or other injuries.
- Ensure that all fasteners and mounting points are securely tightened after installation. Regularly check the security of the installed door handles to prevent loosening.
- Do not use this product for any purpose other than its intended use as an exterior door handle for compatible Honda Civic models.
- Follow all installation and operation guidelines provided in this manual to ensure safe and correct usage.
3. Package Contents
Your package should contain the following items:
- Exterior Door Handles (typically a set of 4: Front Left, Front Right, Rear Left, Rear Right)
- Any necessary mounting clips or hardware (may vary)
Upon opening the package, if there is a protective film on the handles, carefully remove it before installation.
4. Installation Instructions
Replacing exterior door handles typically requires basic automotive tools and some mechanical aptitude. If you are unsure about any step, it is recommended to seek professional assistance.
4.1. Tools You May Need
- Screwdriver set (Phillips and Flathead)
- Trim removal tools (plastic pry tools)
- Socket wrench set
- Gloves and safety glasses
4.2. General Installation Steps
- Prepare the Vehicle: Park the vehicle on a level surface and engage the parking brake.
- Access the Door Panel: Carefully remove the interior door panel of the door where the handle is being replaced. This usually involves removing screws (often hidden under trim caps or in door pulls) and then prying the panel away from the door frame using trim removal tools.
- Disconnect Components: Once the interior door panel is loose, carefully disconnect any electrical connectors (for power windows, locks, etc.) and door handle cables/linkages attached to the panel. Set the panel aside safely.
- Access the Old Handle: Locate the mounting bolts or screws for the exterior door handle from inside the door cavity.
- Disconnect Linkages: Carefully disconnect the lock rod and door latch cable from the old exterior door handle.
- Remove Old Handle: Unscrew or unbolt the old exterior door handle and carefully remove it from the door.
- Install New Handle: Position the new exterior door handle into the door opening. Ensure it sits flush.
- Secure New Handle: Fasten the new handle with the original or provided mounting bolts/screws. Do not overtighten.
- Reconnect Linkages: Reconnect the lock rod and door latch cable to the new handle. Test the handle's operation (both opening and locking) before reassembling the door.
- Reassemble Door: Reconnect all electrical connectors and door handle cables to the interior door panel. Carefully align and reattach the interior door panel, ensuring all clips engage properly. Reinstall all screws.
- Final Check: Test the new door handle from both inside and outside the vehicle to ensure it operates smoothly and securely.

Image: Rear view of four door handles, illustrating mounting points and spring mechanisms.

Image: Close-up rear view of a single door handle, showing its mounting structure.
5. Operating Your Door Handles
Once properly installed, your new exterior door handles operate identically to the original equipment. Simply pull the handle to unlatch the door. Ensure the door is fully closed and latched before driving.
6. Maintenance
- Cleaning: Clean the door handles with a soft cloth and mild automotive soap and water. Avoid abrasive cleaners or solvents that could damage the finish.
- Inspection: Periodically inspect the door handles for any signs of wear, damage, or looseness. Ensure all mounting points remain secure.
- Lubrication: If the handle mechanism feels stiff over time, a small amount of silicone-based lubricant can be applied to the moving parts within the door mechanism (accessible from inside the door panel).
7. Troubleshooting
7.1. Handle Feels Loose or Wobbly
- Check Mounting: Ensure all mounting screws/bolts are securely tightened.
- Internal Mechanism: Verify that the internal linkages are properly connected and not binding.
7.2. Door Does Not Open or Close Properly
- Linkage Adjustment: The internal door latch cable or lock rod may need adjustment. Ensure they are correctly attached and have proper tension.
- Obstruction: Check for any obstructions within the door mechanism.
7.3. Lock Pin Issues
- Alignment: If the lock pin feels different or doesn't operate smoothly, check its alignment and connection to the internal locking mechanism. Minor adjustments may be needed to ensure proper function with your vehicle's existing lock system.
8. Specifications
| Feature | Detail |
|---|---|
| Brand Name | dawndesslo |
| Item Type | Door Handles |
| Car Model Compatibility | Honda Civic EK3, EK4, EK9 |
| Model Year Compatibility | 1996, 1997, 1998, 1999, 2000 |
| Material | ABS |
| OEM Part Numbers | 72180-S04-003, 72140-S04-003, 72680-S04-003, 72640-S04-003 |
| Special Features | Car Exterior Door Handle |
| Origin | Mainland China |

Image: Front view of a single 'Rear Left' door handle.
9. User Tips
- Included Clips: Some packages may include new clips for installation, which can be helpful if your old ones are damaged or missing. Always check your package contents.
- Size Variation: Be aware that aftermarket handles might be slightly smaller than the original equipment manufacturer (OEM) handles. This typically does not affect functionality.
- Lock Pin Adjustment: The lock pin mechanism might differ slightly from stock. You may need to make minor adjustments during installation to ensure it works correctly with your vehicle's locking system.
10. Frequently Asked Questions (FAQ)
Q: Are these handles compatible with a Honda Logo 2001?
A: No, these handles are specifically designed for Honda Civic EK3, EK4, and EK9 models from 1996-2000. Compatibility with other models or years is not guaranteed.
Q: What are the dimensions of these handles?
A: Specific dimensions are not provided in this manual, but the handles are designed to be a direct fit replacement for the specified Honda Civic models. Refer to the specifications section for compatible vehicle details.
Q: Are these available in other colors, such as gray, for a Civic 2000?
A: This manual describes the standard product. Availability of different colors depends on the seller's current stock. Please check the product listing for color options.
11. Warranty & Support
For any warranty claims or technical support, please refer to the seller or manufacturer from whom you purchased this product. Keep your proof of purchase for any warranty-related inquiries.
