eletechsup ND0533MA/B

Contents

ND0533MA/B Mini Size 2A DC-DC Buck Converter Module User Manual

Model: ND0533MA/B | Brand: eletechsup

1. Important Safety Information

Please read all instructions carefully before using this product. Failure to follow these instructions may result in product damage or personal injury.

  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not expose to water or moisture.
  • Handle with care to avoid cuts or injuries.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.

For detailed safety and compliance information, please refer to the full user manual PDF: User Manual (PDF)

2. Product Overview

The ND0533MA/B is a mini-sized DC-DC buck converter module designed to step down an input voltage of 3.3-5.5V to a stable 3.3V output. It features high efficiency, low quiescent current, and various protection mechanisms, making it suitable for a wide range of electronic projects.

ND0533MA/B DC-DC Buck Converter Module

Figure 1: ND0533MA/B DC-DC Buck Converter Module (no pins)

ND0533MA/B DC-DC Buck Converter Module with pins

Figure 2: ND0533MA/B DC-DC Buck Converter Module (with pins)

3. Setup and Installation

3.1 Unpacking and Initial Inspection

  1. Carefully remove the module from its packaging.
  2. Inspect the module for any visible damage. Do not use if damaged.
  3. Remove any protective films from the device before first use.

3.2 Wiring Diagram

Connect the input voltage (3.3-5.5V) and ground to the respective input pins, and connect your load to the 3.3V output and ground pins as shown in the diagram below.

Wiring Diagram for ND0533MA/B Module

Figure 3: Wiring Diagram

  • Input (Vin): Connect your DC power source (3.3V to 5.5V) to the 'Vi' pin.
  • Ground (GND): Connect the ground of your power source and load to the 'GND' pin.
  • Output (Vout): Connect your 3.3V load to the 'Vo' pin.

4. Operating Instructions

Once correctly wired, the module will convert the input voltage to a stable 3.3V output. Ensure your input voltage is within the specified range to prevent damage.

4.1 Key Operating Characteristics

  • Input Voltage Range: 3.3V - 5.5V DC
  • Output Voltage: 3.3V DC (±2.0% deviation)
  • Maximum Output Current: 1.8A (long-term), 2.2A (short-term)
  • Efficiency: Up to 97% (e.g., @4.2V to 3.3V/500mA)
  • Low Quiescent Current: 20µA
Features of ND0533MA/B Module

Figure 4: Module Features

5. Maintenance

  • Keep the module clean and free from dust and debris.
  • Store the module in a dry place, away from moisture and extreme temperatures.
  • Turn off the power to the module when not in use.

6. Troubleshooting

If the module is not functioning as expected, consider the following:

  • No Output Voltage:
  • Ensure the input voltage is within the 3.3V-5.5V range. The maximum input voltage must not exceed 6V.
  • Verify all connections (input, output, ground) are secure and correct according to the wiring diagram.
  • Unstable Output Voltage:
  • Ensure the input power is sufficient and greater than the output power, accounting for the module's own power consumption.
  • Check that the output load does not exceed the maximum long-term current of 1.8A.
  • Module Overheating:
  • Reduce the output current if it's consistently near or above the maximum limits.
  • The module has overtemperature shutdown protection, which will activate if it gets too hot.
Important Usage Notes

Figure 5: Important Usage Notes

7. Specifications

FeatureSpecification
TypeDC/DC Converters
Output TypeSINGLE
Input Voltage3.3V - 5.5V DC
Output Voltage3.3V DC (±2.0% deviation)
Output Current (Max)1.8A (long-term), 2.2A (short-term)
Output Power1 - 50W
EfficiencyUp to 97%
Quiescent Current20µA
Operating Frequency1.2MHz
Operating Temperature-40°C to +85°C
Dimensions (no Pin)15mm x 11mm x 5.7mm
Weight (with Pin)1.1g
Weight (no Pin)0.9g
CertificationNONE
CustomizableYes
Module Size and Weight Comparison

Figure 6: Module Size and Weight

8. User Tips

  • This module is ideal for powering microcontrollers (e.g., UNO, MEGA2560, STM32), breadboards, Wi-Fi modules (ESP8266), Bluetooth modules (HC-05), and various wireless modules (NRF24L01+).
  • Its small size and light weight make it suitable for compact projects and model aircraft.
  • Always double-check your input voltage and current requirements for your specific application to ensure stable operation and prevent damage.

9. Warranty and Support

This product is manufactured by Guangzhou Keshen Electronic Technology Co., Ltd. For technical support or inquiries, please contact the manufacturer directly.

Manufacturer Contact Information:

  • Manufacturer: Guangzhou Keshen Electronic Technology Co., Ltd
  • Address: CN-Room 301, No. 8-1 Beixin Street, Kemulang Aotou, Tianhe District, Guangzhou City
  • Email: eletechsup@163.com
  • Phone: 86-18102739603

EU Authorized Representative:

  • Representative: TOCYA TRADING
  • Address: 79 rue de patay, 75013, Paris
  • Email: TOCYATRADING75013@outlook.com
  • Phone: 33-143443019

Specific warranty details are not provided in this manual. Please contact the seller or manufacturer for warranty terms and conditions.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.