1. Introduction
The foreverlily Skin Moisture Detector utilizes biological resistance analysis technology for high testing accuracy. It integrates temperature and humidity detection, offering a comprehensive analysis of skin conditions. This device can measure skin moisture, oil content, elasticity, environmental temperature, humidity, and also features test memory, fluorescent agent detection, and banknote inspection functions. Designed for ease of use, portability, and safety, it provides intuitive results through its clear display.
It serves as an excellent tool for beauticians to conduct skin health tests for clients or for individuals to monitor their skin health at home.
Video: Demonstration of the Skin Tester's features, including skin moisture, oil, elasticity, skin age, and fluorescent agent detection, along with basic operation.
2. Product Components
The device consists of the following parts:

Image: Labeled diagram of the Skin Tester showing its various components.
- Fluorescent Lamp: Used for detecting fluorescent agents.
- Telescopic Probe: The sensor that contacts the skin for measurements.
- LED Display: Shows measurement results, temperature, humidity, and battery status.
- Clear Key (O button): Long press for Fluorescent lamp detection; Short press for Memory function.
- Switch Key (Power button): Long press to Power On/Off; Short press for Temperature & humidity detection.
- Temperature and Humidity Sensing Hole: Detects ambient temperature and humidity.
- Type-C Charging Port: For charging the device.
3. Setup and Preparation
Before using your Skin Moisture Detector, ensure it is adequately charged. The device comes with a Type-C charging cable.
Charging Instructions:
- When the battery is low, the backlight will flash, and the device will automatically shut down.
- During charging, the LED display backlight will be red.
- Once fully charged, the LED display backlight will turn green.
- Charging time is approximately 40 minutes for a full charge.
- If not used for a long period, charge the device at least once every 3 months to maintain battery health.

Image: The Skin Tester, Type-C charging cable, and user manual included in the package.
4. Operating Instructions

Image: Visual guide illustrating the steps for using the Skin Tester.
4.1. Skin Test (Moisture, Oil, Elasticity, Skin Age)
- For accurate results, perform tests at room temperature on skin free of sweat, body hair, or cosmetics.
- Remove the probe protective cover.
- Long press the Power button to turn on the device. The display will show "00.0%" after a beep.
- Place the telescopic probe firmly against the skin area you wish to test for 2 seconds. You will hear two beeps, indicating the measurement is complete and the results are displayed.
- Interpreting Skin Test Results:
- Moisture:
- Red light: <35% (Dry)
- Yellow light: 35%-50% (Normal)
- Green light: >50% (Excellent) - Oil:
- Green light: <30% (Excellent)
- Yellow light: 30%-35% (Middle)
- Red light: >35% (Oily) - Elasticity:
- Red light: <50% (Poor)
- Yellow light: 50%-60% (Middle)
- Green light: >60% (Excellent) - Skin Age: The device calculates an approximate skin age based on the moisture, oil, and elasticity values. This is for reference only.
- Moisture:
- For continuous testing, simply touch the probe to the next skin area (without pressing any buttons). You will hear two beeps when the test is complete. Allow at least 2 seconds between consecutive tests.
- The display backlight will turn off 30 seconds after the test is completed. The device will automatically shut down if there is no operation for 1 minute, or you can long press the Power button for 3 seconds to turn it off.

Image: Illustrates normal moisture ranges for forehead, eye sockets, and cheeks, differentiating between summer and winter, with color codes for skin condition.
4.2. Fluorescent Agent Detection
- While the device is powered on, long press the 'O' key for 3 seconds. The UV fluorescent lamp at the top of the device will light up.
- Point the UV lamp towards the object you wish to inspect.
- If the object contains fluorescent agents, it will appear blue under the UV light. Objects without fluorescent agents will show their original color.
- To turn off the fluorescent lamp, long press the 'O' key for 3 seconds again.

Image: Shows the device's UV light in action, detecting fluorescent agents on a facial mask.
4.3. Temperature and Humidity Detection
- While the device is powered on, short press the Power button. The device will automatically detect and display the ambient temperature and humidity.
- Note: Temperature and humidity readings can be affected by hand warmth. For the most accurate results, place the device down for at least 1 minute before taking a reading.
5. Memory Function
The device stores up to 8 sets of test records, allowing you to track changes in your skin condition over time.
- To access stored data, short press the 'O' key.
- Each short press will cycle through the 8 historical test records, from the first to the eighth.

Image: The device display showing current skin data alongside a previous measurement for comparison.
6. User Tips
- Track Your Progress: Keep a log of your skin test readings (times and scores) to monitor your skin's performance over time. This will help you identify which skincare products and routines are most effective for you.
- Stay Hydrated: If your moisture readings consistently indicate dehydration, consider increasing your daily water intake and adjusting your moisturizing routine.
- Morning Readings: If your morning skin moisture reading is consistently below 5% of the normal range, it may indicate a need for more intensive skincare or hydration.
7. Troubleshooting
Common Issues and Solutions:
- Inaccurate Readings:
- Ensure the device is tested at room temperature.
- Test on dry skin, free of sweat, hair, or cosmetics.
- Make sure the telescopic probe is fully pressed against the skin during the test.
- Device Not Responding:
- Check battery level and charge if necessary.
- If the device automatically shuts down, it may be due to low battery or inactivity.
- System Preparation Time: The system requires a short preparation time between tests. Ensure a minimum 2-second interval between consecutive measurements.
8. Specifications
| Feature | Detail |
|---|---|
| Item Type | Skin Moisture Detector |
| Dimensions (L x W x H) | 125 x 32 x 22 mm (approx. 4.9 x 1.3 x 0.9 inches) |
| Voltage | 3.7V 10mA (Below-50V AC, SELV AC) |
| Battery Capacity | 3.7V/300mAh |
| Charging Time | 40 minutes |
| Continuous Use Time | 180 minutes |
| Operating Temperature | 5℃ - 40℃ (41°F - 104°F) |
| Relative Humidity | Below 70% |
| Material | Acrylic |
| Certification | CE |
| Number of Pieces | One Unit |

Image: Detailed diagram showing the dimensions and key specifications of the Skin Tester.
9. Maintenance and Care
- Cleaning: Keep the device clean. Do not use water, other liquids, or acidic/alkaline solutions to wipe the device.
- Storage: If the device will not be used for an extended period, ensure it is charged at least once every 3 months to preserve battery life.
- Disassembly: Do not attempt to disassemble or repair the instrument yourself. Unauthorized disassembly may void any potential warranty and could damage the device.
- Liquid Contact: Prevent water or any other liquids from entering the device.
10. Warranty and Support
For any questions, technical support, or warranty inquiries, please contact the seller or refer to the official product page. A detailed user manual in PDF format is also available for download: User Manual (PDF).