Yovanxer DQ-FSBSP100

Contents

Yovanxer ALR PET Crystal Fixed Frame Projection Screen User Manual

Model: DQ-FSBSP100

Yovanxer ALR PET Crystal 100-inch fixed frame projection screen displaying a vibrant image of hot air balloons over mountains.

Image: The Yovanxer ALR PET Crystal 100-inch fixed frame projection screen showcasing its display quality with a colorful image of hot air balloons over a scenic mountain landscape.

1. Introduction

Thank you for choosing the Yovanxer ALR PET Crystal Fixed Frame Projection Screen. This manual provides essential information for the proper installation, operation, and maintenance of your product. Please read it carefully before installation and use, and keep it for future reference.

Important Note: Every screen undergoes special quality checks. The manufacturer records a video of each screen produced to document its condition upon leaving the factory. We recommend that you also record a video during unpacking for documentation. This will assist in processing any service requests. Damage occurring during installation cannot be claimed. The screen material is very fragile; avoid folding or denting it.

2. Safety Precautions and Operating Requirements

  • To ensure optimal projection quality, adhere to these operating requirements.
  • When assembling, use a clean, flat surface (floor or table) free of obstacles. Cover the surface with clean materials like cloth or blankets to protect the screen.
  • Handle the screen with care during installation to prevent personal injury or product damage.
  • Do not touch the surface of the projection screen with your bare hands.
  • Avoid touching the projection surface with sharp or hard objects to prevent damage. Do not write or draw on the screen.
  • Keep children away from the screen to prevent accidents.
  • Clean the screen surface regularly, ideally every two weeks. Use a soft cotton cloth lightly dampened with water. Do not use chemical cleaners or alcohol.

3. Parts List

Before beginning assembly, verify that all components listed below are present and in good condition.

ItemQuantity
Inner Frame Sections6
Outside Frame Sections6
Corner Connectors (Type 1)4
Corner Connectors (Type 2)4
Corner Protectors4
Projection Screen Material1
Fiberglass Strips6
Support Rod1
4mm Hexagon Wrench1
Pull Hook1
Tension SpringsN (variable)
Upper Wall Brackets2
Under Wall Brackets2
M5*5 Pan Head Screws16
Gloves2
Wall Bracket Screws8
M4*8 Screws16
Level Ruler1
Close-up view of the projection screen frame corners and the spring tensioning mechanism.

Image: Detailed view of the screen's ultra-thin border frame corners and the spring system used for tensioning the screen material.

4. Setup and Installation

Note on Diagrams: Due to URL restrictions, detailed assembly diagrams from the original manual cannot be embedded. Instructions are provided textually. Refer to the official PDF manual for visual guidance if needed: User Manual (PDF).

4.1 Assemble the Frame

  1. Unpack all components and organize them. Cross-reference with the parts list.
  2. The horizontal inner frame sections are segmented. Splice them together, ensuring the splicing position aligns with any marks on the splicing strip.
  3. Insert the four corner connectors into the vertical inner frame sections.
  4. Assemble the horizontal and vertical inner frame sections to form the inner frame. Secure the corners with M5x5 screws.
  5. Install the support rod(s) across the assembled inner frame. Ensure the support rod is perpendicular to the middle of the frame.

Textual description of frame assembly diagram: The diagram shows how two inner frame sections connect using a connecting rod, secured by M5x5 screws. Corner connectors are shown joining vertical and horizontal frame sections, also secured by M5x5 screws. A tip advises to loosely fit all screws first, align components, then tighten all screws one by one.

4.2 Assemble the Screen Material

  1. Wear the provided gloves to prevent fingerprints on the screen. Lay a clean cloth on a flat, clean, level surface.
  2. Carefully remove the screen material from its packaging. Place the screen face down on the cloth, unroll it, and spread it flat.
  3. Insert the fiberglass strips into the grooves around the screen material. Ensure the strips extend out equally from both ends of the screen.
  4. Carefully place the assembled inner frame onto the screen material. Note: If your screen is an Ultra-Short Throw (UST) Ambient Light Rejecting (ALR) screen, it has a specific "up" and "down" direction. The back of the screen will have an "UP" marking. Align the screen material with the frame's direction and adjust its position according to the alignment marks on the four corners of the screen.
  5. Hook the screen material to the inner frame using the tension springs and the pull hook. Follow this sequence:
    • First, hook springs 1 through 8.
    • Next, hook springs 9 through 12.
    • Finally, hook the remaining springs, working from the middle spring outwards to both sides.
  6. After all springs are hooked, carefully stand the screen up and check for overall flatness. If there are any uneven areas, adjust the tension of the springs locally until the screen is perfectly flat.

Textual description of screen assembly diagrams: One diagram shows the screen material unrolled face down, with fiberglass strips being inserted into its edges. Another diagram illustrates the inner frame placed over the screen material, showing alignment marks and the "UP" indicator on the screen's back. A third diagram details the sequence of attaching tension springs around the frame to the screen material.

4.3 Install the Outside Frame

  1. Place the outside frame sections against the assembled screen and inner frame. Align the four corners precisely.
  2. Lock the inner and outer frames together using M4x8 screws. If the frame has a brand LOGO, ensure it is positioned at the bottom of the screen.
  3. Adjust each corner of the outside frame to minimize any gaps, then tighten the screws. Work corner by corner. For horizontal outside frame sections, if a gap is too large, gently push the left and right sections inward to close it.
  4. Finally, attach the corner protectors to all four corners of the frame.

Textual description of outside frame installation diagram: The diagram shows the outside frame sections being placed over the inner frame and screen material. Corner connectors are used to join the outside frame sections, and M4x8 screws secure the outside frame to the inner frame. A screw nut is also indicated for securing.

4.4 Wall Installation

  1. Identify the upper and under wall brackets and their correct installation direction (the end with springs inside the groove faces up for the upper bracket).
  2. Install the wall hangers (upper and under wall brackets) on your wall according to the screen's dimensions.
    • Required Tools: Level ruler, hammer drill, pencil, ladder.
    • Horizontal Placement: The wall brackets should be approximately 30cm from both sides of the screen's edges.
    • Vertical Placement: The height of the lower edge of the screen from the ground should generally be between 600mm and 800mm.
    • Mark the drilling points accurately using the level ruler and pencil before drilling.
    • Secure the wall brackets using the wall bracket screws.
  3. Hang the assembled screen onto the installed wall brackets:
    • First, buckle the top edge of the screen into the upper wall brackets from top to bottom.
    • Then, push the bottom of the screen forward towards the wall.
    • Lift the screen slightly to insert the bottom edge into the under wall brackets, compressing the springs for a secure fit.

Textual description of wall installation diagrams: One diagram shows wall measurements for bracket placement: 30cm from side edges, 7.5cm between upper bracket screws, 25cm between upper and lower bracket screw lines, and a recommended screen bottom height of 60-80cm from the ground. Another diagram illustrates the process of hanging the screen: first engaging the top brackets, then pushing the screen towards the wall, and finally lifting to engage the bottom brackets.

Video: A demonstration of the Yovanxer projection screen displaying various high-quality video content, showcasing its clarity and performance in a typical room setting.

5. Operating Your Projection Screen

Your Yovanxer ALR PET Crystal Fixed Frame Projection Screen is designed for use with Ultra Short Throw (UST) projectors. For optimal performance:

  • Projector Placement: Position your UST projector directly below the screen, ensuring it is centered and at the correct distance to fill the screen perfectly.
  • Screen Orientation: Ensure the screen is mounted with the correct "UP" orientation, especially for ALR screens, to effectively reject ambient light from above.
  • Ambient Light: While ALR screens significantly reduce the impact of ambient light, for the best viewing experience, minimize direct light sources hitting the screen.
  • Viewing Angle: The screen offers a wide 160-degree viewing angle, providing a clear picture from various positions in the room.

6. Maintenance

To keep your projection screen in pristine condition and ensure long-lasting performance:

  • Regular Cleaning: Clean the screen surface regularly, ideally every two weeks, or as needed.
  • Cleaning Method: Use a soft, clean cotton cloth lightly dampened with plain water. Gently wipe the screen surface.
  • Avoid Harsh Chemicals: Do not use any chemical cleaners, solvents, or alcohol on the screen, as these can damage the delicate screen material.
  • Protect from Damage: Avoid touching the screen with sharp objects, writing on it, or applying excessive pressure.

7. Troubleshooting

This manual does not include a dedicated troubleshooting section. Most issues related to a projection screen are typically installation-related or projector-related.

  • Uneven Screen Surface: If the screen appears wavy or uneven after assembly, re-check the tension of the springs. Adjust individual springs as needed to achieve a perfectly flat surface.
  • Poor Image Quality: Ensure your projector is correctly aligned with the screen and is an Ultra Short Throw (UST) model. Verify the screen is mounted with the correct "UP" orientation for optimal ambient light rejection.
  • Physical Damage: If the screen material is damaged during installation, it cannot be claimed under warranty. Handle with extreme care.

For further assistance, please contact customer support.

8. Specifications

FeatureDetail
Brand NameYovanxer
Model NumberDQ-FSBSP100
Screen TypeFrame Screen
MaterialPET Crystal
Format16:9
Size100 Inch
StyleUltra-thin border Fixed Frame
TypeALR UST Projector Screen (Ambient Light Rejecting, Ultra Short Throw)
Suitable ForAll kinds of Ultra Short Throw Projectors
Viewing Angle160 degrees
UsageCinema, Training Institutions, Meeting Rooms, Home Theater, etc.
CertificationCE
PortableNo
LED BacklightOptional (not included with standard product)
CustomizableSupported
Hign-concerned ChemicalNone

9. User Tips

  • Unpacking: Always unpack the screen carefully on a clean, soft surface to prevent accidental damage or scratches. Consider having a second person assist.
  • ALR Orientation: Double-check the "UP" marking on the back of the screen during assembly and installation. Incorrect orientation will significantly reduce the ambient light rejecting capabilities.
  • Projector Alignment: Precision is key for UST projectors. Take your time to align the projector perfectly with the screen to avoid keystone distortion and ensure the image fills the screen edge-to-edge.
  • Wall Mounting: Use a stud finder to mount wall brackets securely into wall studs for maximum stability, especially for larger screens.

10. Warranty and Support

Your Yovanxer ALR PET Crystal Fixed Frame Projection Screen comes with a 2-year warranty from the date of purchase, covering manufacturing defects.

For technical support, warranty claims, or any inquiries, please contact:

  • Service Hotline: 008618621934178
  • Email: sales@dqprojection.com

Please have your model number (DQ-FSBSP100) and purchase details ready when contacting support.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.