1. Introduction
The VDIAGTOOL VD80BT Lite Diagnostic Tool interfaces with the electronic control unit (ECU) of a vehicle to retrieve diagnostic trouble codes (DTCs), access data stream information, and command active tests (bi-directional control tests). Various vehicle control systems, such as engine, transmission, anti-lock brake system (ABS), SRS (Airbag) system, Chassis, Body, etc., are readily diagnosed using this Diagnostic Tool. It is capable of graphing up to eight (8) live data parameters on a single screen and also includes ECU information.
This manual introduces the basic features of the Diagnostic Tool, including the control buttons, data ports, battery pack, and power sources. Technical Specifications are provided at the end of this chapter.
2. Safety Information
For your own safety and the safety of others, and to prevent damage to the device and vehicles upon which it is used, it is important that the safety instructions presented throughout this manual be read and understood by all persons operating or coming into contact with the device.
There are various procedures, techniques, tools, and parts for servicing vehicles, as well as in the skill of the person doing the work. Because of the vast number of test applications and variations in the products that can be tested with this equipment, we cannot possibly anticipate or provide advice or safety messages to cover every circumstance. It is the automotive technician's responsibility to be knowledgeable of the system being tested. It is crucial to use proper service methods and test procedures. It is essential to perform tests in an appropriate and acceptable manner that does not endanger your safety, the safety of others in the work area, the device being used, or the vehicle being tested.
Before using the device, always refer to and follow the safety messages and applicable test procedures provided by the manufacturer of the vehicle or equipment being tested. Use the device only as described in this manual. Read, understand, and follow all safety messages and instructions in this manual.
2.1 Safety Messages
Safety messages are provided to help prevent personal injury and equipment damage. All safety messages are introduced by a signal word indicating the hazard level.
Danger:
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders.
Warning:
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders.
2.2 Safety Instructions
The safety messages herein cover situations VDIAGTOOL is aware of. VDIAGTOOL cannot know, evaluate or advise you as to all of the possible hazards. You must be certain that any condition or service procedure encountered does not jeopardize your personal safety.
Danger:
When an engine is operating, keep the service area WELL VENTILATED or attach a building exhaust removal system to the engine exhaust system. Engines produce carbon monoxide, an odorless, poisonous gas that causes slower reaction time and can lead to serious personal injury or loss of life.
2.3 Safety Warnings
- Always perform automotive testing in a safe environment.
- Wear safety eye protection that meets ANSI standards.
- Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
- Operate the vehicle in a well ventilated work area, for exhaust gases are poisonous.
- Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.
- Put blocks in front of the drive wheels and never leave the vehicle unattended while testing.
- Be extra cautious when working around the ignition coil, distributor cap, ignition wires and spark plugs. These components create hazardous voltages when the engine is running.
- Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
- Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
- Keep the test equipment dry, clean, free from oil, water or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary.
- Do not drive the vehicle and operate the test equipment at the same time. Any distraction may cause an accident.
- Refer to the service manual for the vehicle being serviced and adhere to all diagnostic procedures and precautions. Failure to do so may result in personal injury or damage to the test equipment.
- To avoid damaging the test equipment or generating false data, make sure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure.
- Do not place the test equipment on the distributor of the vehicle. Strong electro-magnetic interference can damage the equipment.
3. What's In The Box
The VDIAGTOOL VD80BT LITE package includes the following items:
- 1 x VD80BT LITE Main Diagnostic Tablet
- 1 x VCI Box
- 1 x US Power Charger
- 1 x EU Power Charger
- 1 x UK Power Charger
- 1 x Quick Start Guide
- 1 x Type-C to Type-A Adapter
- 1 x Type-C to Type-C Charger Cable
- 1 x Hard Case
- 1 x Color Carton
4. Setup Instructions
4.1 Power Sources
The VDIAGTOOL VD80BT Lite Diagnostic Tool can receive power from either of the two sources:
- Internal Battery Pack
- AC Power Supply
The VCI Box is powered by connecting it to the vehicle OBDII port.
4.2 Internal Battery Pack
The VDIAGTOOL VD80BT Lite Diagnostic Tool can be powered from the internal rechargeable battery pack. A fully charged battery provides sufficient power for about 3.5 hours of continuous operation.
Battery charging occurs when the Diagnostic Tool is connected to the AC Power Supply and to a live AC power source.
4.3 AC Power Supply
The Diagnostic Tool can be powered from a standard AC outlet using the AC power supply. The connector on the end of the output cable of the AC power supply attaches to the DC power supply input jack on top of the Diagnostic Tool. Use only the AC power supply provided.
4.4 Turning On/Off and Emergency Shutdown
4.4.1 Turning On
Press and hold the power button on the top right of the Diagnostic Tool for 3 (three) seconds. It will automatically turn on when the internal battery pack has power or is connected to an AC power supply. If the internal battery pack is completely drained, you may need to wait a few minutes before turning it on.
4.4.2 Turning Off
Press and hold the power button again for over 3 (three) seconds, and the Diagnostic Tool will turn off automatically.
Important:
All vehicle communication must be terminated BEFORE turning off the Diagnostic Tool. A warning message displays if you attempt to turn the Diagnostic Tool off while communicating with the vehicle. Forcing a shutdown while communicating may lead to ECM problems on some vehicles. Never disconnect the VCI Box when the Diagnostic Tool is communicating with the vehicle ECM.
4.4.3 Emergency Shutdown
During normal operation, turn the Diagnostic Tool off using the Turning Off procedure above. The emergency shutdown procedure should only be used if the Diagnostic Tool does not respond to navigation or control buttons or exhibits erratic operation. To force an emergency shutdown, press and hold the Power button for five seconds until the Diagnostic Tool turns off.
Important:
Using the emergency shutdown procedure while communicating with the vehicle ECM may lead to ECM problems on some vehicles.
4.5 Connecting the VCI Box
The Diagnostic Tool uses a VCI box that has an OBDII-16 male connector for vehicle communication. The VCI box connects to the Diagnostic Tool via WiFi. If the WiFi function is not working currently, you can also connect the Diagnostic Tool directly via a Type-C cable.
To establish communication between the Diagnostic Tool and the vehicle, follow these steps:
- Turn on the Diagnostic Tool.
- Plug the VCI box into the vehicle's OBDII port. Make sure the Power and Wi-Fi indicators light up.
- Turn on the ignition and run the diagnostic program on the Diagnostic Tool.
4.6 Wi-Fi Connection
This Diagnostic Tool can connect to 2.4 GHz or 5.0 GHz frequency hotspots or Wi-Fi. Swipe up the hidden bottom toolbar and see the tab menu. Click Home > Network & internet > Switch on Wi-Fi connection > Click Wi-Fi icon to view available Wi-Fi networks > Select the Wi-Fi you want to connect and input the password.
If your Wi-Fi does not work well or you are in a field that does not have home Wi-Fi connection, you can connect to your mobile phone hotspot.
- For iOS users: Go to Settings > Personal Hotspot > Switch on "Allow Others to Join" and "Maximize Compatibility" to set your phone and connect to the hotspot from your Diagnostic Tool.
- For Android phone users: Go to Settings > Wireless & networks > Tethering & portable hotspot > Portable WLAN hotspot > Switch on hotspot > Configure WLAN hotspot > Encryption Type > WPA2 PSK > Show advanced options and make sure "Max connections allowed" has user left for the Diagnostic Tool.
Note:
Wi-Fi connection is not required in diagnostics for most vehicle brands. Diagnostics for just a few vehicle brands like Peugeot require accessing an online server and should connect to Wi-Fi while diagnosing.
4.7 Product Activation
When the Diagnostic Tool runs out of trials, you must register and activate it to continue using the diagnostic programs.
To register the Diagnostic Tool, click "Register" > input your email address > set and repeat the password > agree to the User Terms and submit your registration. Once registration is completed, the Diagnostic Tool is activated. You can use the email address and password for login (the Diagnostic Tool will remember your account information once registered, so you don't need to log in every time).
Note:
If you are unable to register the Diagnostic Tool or can't see the activation screen, contact our support team via support@vdiagtool.com or fill out the tech support form on our website www.vdiagtool.com for assistance.
4.8 Language Settings
To change the language of the Android tablet, go to "Settings" > "Language" and select your desired language.
To use the diagnostic program in the desired language, you need to contact support and provide the S/N of the Diagnostic Tool to authorize the language software program. Once authorized, download all software programs for the new language and set the Android tablet's language as indicated.
- Supported Languages: Arabic, Traditional Chinese, Danish, German, Greek, English, Spanish, Finnish, French, Hungarian, Italian, Japanese, Korean, Dutch, Norwegian, Polish, Portuguese, Russian, Swedish, Thai, Turkish, Vietnamese.
5. Operating Instructions
5.1 Diagnostic Screen Layout & Icons
When the Diagnostic Tool is turned on, it will run the diagnostic program automatically. The Diagnostic Tool uses a hidden toolbar at the bottom of the diagnostic tablet; swiping up from the bottom will bring up the toolbar for 3 seconds. Clicking the home button on the hidden toolbar will bring up the main screen of the diagnostic tablet.
5.1.1 Main Screen Icons
- Auto Scan: Automatically detects and decodes the VIN number, then comprehensively scans all available vehicle electronic control modules for diagnostics.
- Manual Diagnosis: Navigates the vehicle by Auto VIN, Manual Input, or manual selection of vehicle make, model, year, and configurations for diagnostics. Also allows checking the DEMO program and performing OBDII tests.
- Special Functions: Includes commonly performed maintenance services used by car repair professionals and DIYers.
- Report: Contains diagnostic reports, data playback, and data view functions.
- Updates: Allows downloading diagnostic software programs individually or in batches.
- More: Sets user account and workshop profile, checks subscription period, firmware information, uses the endoscope, and accesses the user manual in PDF.
- Settings: Sets diagnostic software language, units of measurement, USB mode, OS settings, adjusts volume and brightness, and checks App version, OS version, Serial Number, and VCI number.
- Remote Control: Runs TeamViewer for remote assistance.
- Service Center: Provides contact methods and social media accounts for support.
5.2 How to Diagnose Vehicles
The Diagnostic Tool allows communication with a vehicle's electronic control systems to retrieve DTCs, view PID data, perform active tests, and conduct various advanced resets, relearns, matchings, adaptations, and initializations.
5.2.1 My Vehicles
The "My Vehicles" function allows you to add frequently used diagnostic programs to save time. Click the Manual Diagnosis icon on the diagnostic screen to see "My Vehicles" listed in the top taskbar.
To add a diagnostic program: Click the add icon > select the region where the vehicle brand originated > select the brands you often use > click "completed".
To remove a diagnostic program: Click the pen icon > select the program > click "Remove".
5.2.2 Compatibility Check
This Diagnostic Tool is compatible with all OBDII/EOBD vehicles for generic OBDII tests and a vast number of vehicle makes and models in the United States, Europe, Asia, Australia, etc., for all electronic control system diagnostics. However, available functions vary by vehicle.
Important:
Special Functions on the main diagnostic screen are not universally available to all vehicles. Functions available to a specific vehicle are strictly subject to compatibility check, providing the vehicle VIN, make, model, and year.
To check compatibility, consult tech support via support@vdiagtool.com or visit www.vdiagtool.com/support/vehicle-coverage.
5.2.3 Software Program Version
The Diagnostic Tool displays the current software program version at the bottom of each vehicle manufacturer's entry. A red up arrow indicates a newer software program version is available for download.
5.2.4 Demo Program
The "DEMO" program simulates the vehicle navigation process, available functions, and menu appearance. Use it to practice using the Diagnostic Tool before activation.
Important:
The DEMO program may not reflect the latest vehicle diagnostic process or the real screen. It is NOT used for vehicle coverage/compatibility checks.
5.2.5 Trial Mode
The Diagnostic Tool comes with a few trials to check its functions or vehicle compatibility before activation. The number of trials varies based on factory inspections.
5.2.6 Diagnose Vehicles
The vehicle must be correctly identified for the Diagnostic Tool to communicate and perform diagnostics. The vehicle identification sequence is menu-driven; follow screen prompts to enter information. Exact procedures may vary by vehicle make, model, and year.
To identify a vehicle for diagnostics, you have four options:
- Auto Scan: Click "Auto Scan" on the diagnostic screen to scan the vehicle VIN and decode it automatically.
- Manual Diagnosis: Click "Manual Diagnosis" on the diagnostic screen to bring up the vehicle selection menu. Click the VIN icon, then "Manual Input" to enter the 17-digit VIN manually.
- Automatic Detection: Click "Manual Diagnosis" > Select region > Select vehicle brand > Select "Automatic Detection" to automatically detect and identify the vehicle.
- Manual Selection: If Auto Scan, Manual Input, and Automatic Detection fail, select "Manual Selection" to identify the vehicle. This is the most reliable option.
Note:
Auto Scan does NOT work on all vehicles. If Auto Scan fails, try other options. Some VINs cannot be decoded; if Auto Scan and Manual Input fail, try Automatic Detection or Manual Selection. Automatic Detection does not work on all models; use Manual Selection if all three options fail.
5.2.7 Submit Feedback
Click the message icon on the top right corner to submit feedback to our support team if you encounter issues with the app or software programs.
5.2.8 CAN Fast Scan
Scans all available vehicle systems for vehicles using CAN protocol for communication post-2005 much faster.
5.2.9 System Selection
Allows you to pick an individual vehicle module for diagnostics if you know where the car problems might be.
5.2.10 Diagnostics
Once the vehicle is identified, the Diagnostic Tool can scan and access vehicle electronic control systems to pull diagnostic trouble codes (DTCs), retrieve PID data (Parameter IDs), freeze frame, ECU information, and perform diagnostic tests like active tests (bi-directional controls) and advanced resets, relearns, matchings, adaptations, and initializations.
5.2.10.1 Read Codes
Displays diagnostic trouble code (DTC) records from the vehicle electronic control module. If the tool shows "System is OK" or "No Trouble Code", it means either no related fault codes are stored in the ECU or some faults are not detected.
5.2.10.2 Clear Codes
Erases DTC records (current or history) and other data from the vehicle electronic control module. A confirmation screen displays to prevent accidental data loss.
5.2.10.3 Live Data (PID Data)
Displays real-time PID data for various sensors. You can view data in a list, individual graphing, analog dashboard, set max/min values, and view custom PID data up to 8 sensors.
5.2.10.4 Freeze Frame
When a fault code is triggered, the vehicle ECU saves a "snapshot" of critical parameter values at that moment. This data helps analyze the root cause of the fault code.
5.2.10.5 Active Tests (Bi-Directional Controls)
Checks the operation of certain actuators (solenoids, valves, relays) by sending commands to the vehicle's ECU. This allows for in-depth diagnostics and precise fault detection.
5.2.10.6 Special Functions
Performs advanced features like resets, relearns, matchings, adaptations, and initializations. The menu displayed varies across vehicles.
5.2.11 Full System Diagnostic Report
After diagnostics, input the VIN, mileage, and model year, then click "OK" to generate a diagnostic report for review or sharing. This report is called a "Full System Diagnostic Report" to differentiate it from the "Fault Code Report" generated on the vehicle scan/Auto Scan screen.
5.2.12 Fault Code Report
A simplified diagnostic report that only displays retrieved fault codes and impacted vehicle systems.
5.2.13 Diagnostic Speed
The Diagnostic Tool provides fast scanning and diagnostics. Speed varies based on vehicle communication protocol and the number of control modules.
5.2.14 Integrated Module
In older vehicle models, manufacturers may integrate two or more electronic control systems into one module (e.g., Powertrain Control Module (PCM) integrates Engine and Transmission; Brake Control Module (BCM) integrates ABS and EPB).
6. OBDII/EOBD Functions
This chapter describes the concept, protocols, test functions, and basic operation of the OBDII/EOBD function. To find the OBDII/EOBD function, go to MANUAL DIAGNOSIS > Region Selection > OBDII.
This option provides a quick way to check for DTCs, locate the cause of an illuminated malfunction indicator lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform other emissions-related services.
6.1 OBDII Protocols
Global OBD uses 5 communication protocols:
- SAE J1850 PWM
- SAE J1850 VPW
- ISO 14230-4 (KWP2000)
- ISO 9141-2
- ISO 15765-4/SAE J2480
6.2 Basic Operations
To access generic OBDII/EOBD data, follow these steps:
- Click MANUAL DIAGNOSIS on the main diagnostic screen.
- Select the region where the vehicle manufacturer originated.
- Click the OBDII icon beside the DEMO.
6.3 Auto Scan & Protocol Selection
There are two options to access the OBDII/EOBD data of the connected vehicle:
- Auto Scan: The Diagnostic Tool attempts to establish communication by trying each protocol to determine which one the vehicle uses.
- Protocol Selection: If you know your vehicle's communication protocol, select it directly.
6.4 Help
Describes DLC location, DTC library, abbreviations, and OBD background information like OBDII modes.
6.5 10 Modes of OBDII
- Mode $01 - Request Live Data
- Mode $02 - Request Freeze Frames
- Mode $03 - Request Stored Trouble Codes
- Mode $04 - Clear/Reset Stored Emissions Related Data
- Mode $05 - Request Oxygen Sensors Test Results
- Mode $06 - Request On-Board System Tests Results
- Mode $07 - Request Pending Trouble Codes
- Mode $08 - Request Control of On-Board Systems
- Mode $09 - Request Vehicle Information
- Mode $0A - Request Permanent Trouble Codes
6.6 OBDII/EOBD Menu
6.6.1 Read Trouble Code
Displays a list of current emission-related DTCs, including Stored Codes (Generic and Manufacturer-Specific), Pending Codes, and Permanent Codes.
6.6.2 Pending Codes
Obtains "pending" or maturing diagnostic trouble codes. These codes met setting conditions during the last drive cycle but need to be met on two or more consecutive drive cycles before the DTC actually sets.
6.6.3 Permanent Codes
Displays a record of any "Permanent" codes. A permanent status DTC is one that was severe enough to illuminate the MIL at some point, but the MIL may not be on at the present time.
6.6.4 Generic & Manufacturer-Specific Codes
DTCs are how OBDII identifies and communicates on-board problems. The first number indicates if the code is SAE generic (0) or manufacturer-specific (1).
6.6.5 Clear Trouble Code (Mode $04)
Clears all emission-related diagnostic data (DTCs, freeze frame data, test results) from the ECM memory.
6.6.6 Live Data (Mode $01)
Displays current emission-related data from the ECM. The left column describes the parameter, and the right column shows its value and unit or state.
6.6.7 Read Freeze Frame (Mode $02)
Displays freeze frame data for any stored emission-related diagnostic trouble code (DTC).
6.6.8 I/M Readiness (Smog Check)
Checks the readiness of the monitoring system, useful before emissions inspections.
7. Special Functions & Maintenance Services
This chapter describes various scheduled service and maintenance functions. Follow on-screen instructions to select execution options, enter values, and perform necessary actions.
7.1 Oil Reset
Resets the engine oil life system after an oil change, allowing the system to calculate the next oil change interval.
- Enter the Oil Reset menu and select the vehicle model.
- Follow screen instructions and press OK.
- Enter maintenance mileage reset menu.
- Click INPUT, enter a reasonable value for remaining oil life, and press OK.
- Confirm the new value and click OK.
- A "Write successfully" message confirms completion.
7.2 EPB (Electronic Parking Brake) Reset
Resets the electronic parking brake system and brake pads (retraction, release of the brake pump), G-sensor, and body angle calibration.
- Enter the EPB menu and choose the vehicle model.
- Follow instructions and press YES.
- Enter the Enter maintenance mode menu and release the handbrake. Press OK.
- Wait for "Successful operation" message and press OK to exit.
- Enter the Exit maintenance mode menu and wait for "Successful operation" message.
7.3 SAS (Steering Angle Sensor) Reset
Calibrates the steering angle sensor to store the current steering wheel position as the straight-ahead position. Clears SAS fault codes upon successful completion.
- Enter the SAS menu and choose the vehicle model.
- Enter the Set steering angle sensor menu and follow instructions.
- Wait for instructions and press YES.
- Follow instructions and press OK.
- Wait for "Function execution is completed" message.
7.4 BMS (Battery Management System) Reset
Evaluates battery charge state, monitors current, registers battery replacement, and activates the rest state of the vehicle. Clears original low battery fault information and performs battery matching.
- Enter the BMS Reset menu and choose the vehicle model.
- Turn on the ignition switch.
- Press OK to continue.
- Enter battery capacity (0-255) and press OK.
- Enter the battery manufacturer and press OK.
- Enter the 10-digit battery serial number and press OK.
7.5 Injector Coding
Writes the identification code of the fuel injector into the ECU so that the ECU can recognize the new injector. Necessary after ECU or injector replacement.
- Enter the Injector coding menu and choose the vehicle model.
- Enter the Fuel injection nozzle injection volume adjustment menu.
- Read the displayed note and press OK.
- Read and confirm the value stored in the cylinders.
- Enter the Change the value of cylinder menu for the replaced injector(s), enter the new 5-digit value, and press OK.
- Wait for "Write successfully" message.
- Turn off the ignition switch.
- Wait for the message to turn on the ignition switch.
- Re-enter the Fuel injection nozzle injection volume adjustment menu to check if new values are shown.
7.6 TPMS (Tire Pressure Monitoring System) Reset
Performs learning, matching, and resetting functions for the tire pressure sensor. Applicable for tire replacement, troubleshooting, or signal loss.
TPMS reset can be further divided into 4 methods: Automatic Relearn, Static Relearn, Copy ID, and OBD Relearn, depending on the specific model.
7.7 ABS Bleeding
Removes air from ABS brake lines to restore ABS brake sensitivity. Performed when ABS contains air, after replacing brake components, or due to severe brake fluid shortage.
- Read operating instructions and precautions.
- Attach bleeder bottle to the left rear bleeder screw.
- Open the left rear bleeder screw.
- Click "OK" to enter the bleed procedure, continuously pump the brake pedal with steady applies every 2 seconds.
- Continue pumping the brake pedal; when air bubbles are no longer visible, select OK to enter the next bleed procedure.
- Repeat for all wheels.
- Stop pumping the brake pedal and close the bleeder screw.
- Click OK to complete.
7.8 ECU Coding & PMI
ECU Coding: Improves vehicle performance and personalizes car settings. Optimizes vehicle performance and customizes car settings for VW/AUDI/SKODA (online coding, component matching, adaptive data reset, flash hidden functions).
ECU Configuration (Flash Hidden Functions): Unlocks hidden functions to activate manufacturer-restricted features (e.g., lifting speed limits). For BMW/VW/AUDI/SKODA/TOYOTA/LEXUS/SCION/MAZDA/FORD/LINCOLN.
PMI (Programmable Module Installation) / ECU Offline Programming: Writes new software, firmware, or updated versions to the ECU. Applicable for Ford, Lincoln, Mazda.
7.9 VAG Guided Function
Provides detailed procedures and guidance for specific repair tasks for VAG vehicles, including replacing parts, calibrating sensors, and resetting the system.
7.10 FCA AutoAuth / CANFD / DoIP Compatibility
The tool supports FCA AutoAuth for Chrysler, Dodge, Jeep, Alfa Romeo, Fiat vehicles (FCA diagnostic account not provided). It also supports CAN FD and DOIP protocols for faster ECU communication and enhanced remote diagnostics.
7.11 Pre-Scan and Post-Scan & Diagnostic Report 2.0
Pre-Scan: Performed before vehicle maintenance to identify existing fault codes and report them to the owner.
Post-Scan: Performed after maintenance to confirm repairs, clear fault codes, and check for new ones.
Diagnostic Report 2.0: Customizable reports with four types, icon display for main systems, and client information.
7.12 Other Special Functions
- Power Balance: Shuts down individual injectors to determine relative power contributed by each cylinder.
- Seat Calibration: Matches or configures seats with memory function after replacement or repair.
- Language Change: Changes the system language of the instrument cluster or control console.
- Control Unit Reset: Resets ECU software when faults occur due to abnormal working temperature or voltage changes.
- Throttle: Resets throttle actuators and learned values to default state.
- Rain/Light Sensor: Resets the rain/light sensor after replacement.
- A/F Reset: Resets or relearns air/fuel ratio parameters.
- HV Battery: Checks the voltage of individual battery packs.
- Gearbox Match: Completes gearbox self-learning after disassembly or repair.
- Crank Sensor Relearn: Performs tooth learning for the vehicle to turn off the MIL.
- Stop/Start Reset: Opens or closes the automatic Start/Stop function via hidden ECU settings.
- EGR Relearn: Learns the EGR valve after cleaning or replacement.
- A/C Relearn: Performs AC system relearn after ECU or actuator replacement.
- Headlight: Initializes the adaptive headlight system (Headlight Adjustment, Matching, or AFS Reset).
- Windows Initialization: Recovers ECU initial memory and automatic ascending/descending function of power windows after battery disconnection.
- VGT Relearn: Calibrates newly installed VGT components.
- Coolant Bleeding: Activates the electric water pump after replacement.
- Suspension: Adjusts vehicle body height sensor for level calibration.
- Airbag Reset: Resets the airbag system and clears crash data.
- Tire Size Reset: Resets tire size parameters after modification or replacement.
- Sunroof Initialization: Recovers ECU initial memory and automatic ascending/descending function of sunroof after battery disconnection.
- Camshaft Learning: Calibrates the engine control unit (ECU) to match the actual camshaft position with the expected position.
8. Software Updates
The software subscription is a yearly fee for all compatible makes and models. When the subscription expires, you can choose to renew or skip. Old software programs remain on the Diagnostic Tool but cannot be updated.
You can update software programs via Wi-Fi or mobile phone hotspot. Mobile hotspot is recommended if home Wi-Fi fails due to network provider restrictions.
If "Network abnormal" appears, try another Wi-Fi or check router settings. Contact support if the issue persists.
8.1 Updating Software Programs
You have two options:
- Update All Software Programs: Click "Update All" at the bottom right of the update menu.
- Update Individual Software Program: Click the "↑" icon next to the specific software program. If the update is interrupted, click the "↑" icon again.
8.2 Deleting Software Programs
If the diagnostic tablet has too much memory and is slow, delete rarely used software programs to free up space.
To delete: Click "Manual Diagnosis" > Select Region > Press and hold the vehicle maker icon > Click "Delete".
Important:
Do NOT delete software programs if the subscription is near expiration. Download all deleted programs before the subscription expires.
9. Troubleshooting & FAQ
9.1 Common Issues and Solutions
- Q: I haven't found I/M readiness in the menu.
A: Enter Manual Diagnosis > Select America/Europe/Asia > Click the "OBDII" icon > Auto Scan/Select OBDII Protocol > I/M Readiness. - Q: Unable to find live sensor data as the generic OBD2 scanner, like short-term/long-term fuel trim.
A: Enter Diagnosis > Select America/Europe/Asia > Click the "OBDII" icon > Auto Scan/Select OBDII Protocol > Live Data > LTFT, STFT or similar term. - Q: Unable to find the misfire data for my Ford/Dodge/Chrysler/Jeep cars?
A: Select Manual Diagnosis-America/Europe/Asia > OBDII (On the top left of the screen) > Auto Scan or Select OBDII Protocol for your car > On Board Monitor Test > Select "Misfire Cylinder Data" or similar term. - Q: How to export live data as CSV files?
A: How to generate CSV files: live data > custom > data export. How to find the CSV files: ES File Explorer > internal storage > diagnosis > csv_records. - Q: I cannot charge the battery now. I plugged in the cord, it's not charging. The battery is almost dead, only about 10% left.
A: Please charge it for over an hour, unplug it from the charger, then press and hold the power button for 15 seconds and see if it solves the issue. Please unplug the USB-C cable from the Diagnostic Tool and press and hold the power button for 15s, and check if it can power up successfully. - Q: Can scanner tune up car?
A: Sorry, VD80BT Lite Diagnostic Tool does not have the capability to tune up car. - Q: Can this scanner still be used once the 3 year free updates are finished?
A: Yes of course, you can still use its last updated software when it expires, even when it expires after three years. - Q: It was frozen until the battery went flat even I tried the reset button and the power button.
A: Please make sure you have updated the App to the latest version (To update the App to the latest, go to Settings > About > App > click the arrow at the right side to check the latest App version and update to the latest.). If yes, please reset to factory settings and check again. If it still does not work, please reach us directly via support@vdiagtool.com. - Q: I cannot update, I've tried wi-fi and cell phone as hotspot, however, keep telling me failure connection.
A: This problem could reside with the setting of your router firewall or the network provider in your region that restricts access to the server, please check if your router firewall can access the server or not. If the problem still exists, please reach us via support@vdiagtool.com. - Q: Any chance to install Google Play store?
A: We are sorry that this diagnostic tool does not support installing Google Play store. However, if you want to install a third-party app, you can download apk file and install it on the diagnostic tool. We don't recommend installing third-party apps as it may slow down its running speed. - Q: So if no WiFi, you can't use the VD80BT Lite?
A: WiFi wireless connection is the type of communication from the VCI to the machine and has nothing to do with the WiFi internet connection. - Q: The auto VIN cannot work on my vehicle.
A: As for auto scan/VIN, it does not cover all vehicles as some vehicles did not store VIN # in the ECU, some VIN # is not included in our coverage database, and some vehicles like Dodge work in "sending command, answering command" mode for vehicle communication. You can try below alternative navigation methods: 1: Turn on the ignition and not start the engine to try auto scan. For older vehicles, please turn on the ignition and start the engine and try auto scan. 2: Manual input VIN #. 3: Diagnosis-America/Europe/Asia-Vehicle Selection-Automatic Detection. 4: Diagnosis-America/Europe/Asia-Vehicle Selection-Manually Selection. - Q: My diagnostic tool cannot connect to WIFI.
A: If it shows "times out", please check your router and make sure that your router selected WPA2, not WPA3 (maximum compatibility), and that it has not blocked the outgoing network traffic to non-US regions like China. Switching to mobile phone hotspot will most likely solve the registration issue. You can switch back to home Wi-Fi for software downloads when activation is done. - Q: How can I change the menu language into Spanish?
A: To change the menu language, please send the S/N of the diagnostic tool to our support team via support@vdiagtool.com and get Spanish software program authorization. When the authorization is done, go to Settings on the diagnostic menu > language > Spanish to change the language of the Android tablet into Spanish, then go to Updates > download all software programs. When all software programs in Spanish have been downloaded and installed, you may use the diagnostic tool in Spanish. - Q: Why the scanner shows the report shared successfully but the email box didn't receive the report?
A: All the reports are sent by our email: noreply@service-vdiagtool.com. The email may be blocked even if the device shows "send successfully". Check your spam folder or whitelist the sender. - Q: When you enter the diagnosis software program, it shows 'license exception' or 'Failed' error message.
A: Try to delete the software programs by pressing and holding it and then re-download it again under 'Updates'. If not, contact support. - Q: Browser can access internet normally, but can not download the updates under "Updates", prompted to 'check the network connection' in the Update.
A: Switch to mobile hotspot or other Wi-Fi and try again. - Q: The device cannot be charged/powered on when connected with the car or plugged into the charger.
A: Please charge for more than one hour first, unplug the charger, press and hold the power button for 15 seconds and to check if it will turn on, and also confirm whether the device screen will light up when charging and try to press and hold the power button for more than 10s to try several times while charging. If the device still won't turn on, please contact support. - Q: When activating the device, shows error message "registration failure" after entering your email address.
A: Try mobile hotspot (recommended) or a different network to activate. - Q: If my diagnostic device is connected to the VCI box via WiFi, does that mean it can't connect to my home WiFi?
A: This is not a correct understanding. The VCI WiFi is different from the home WiFi. While connected to the VCI, you can also connect to the home WiFi to perform software upgrades, etc.
10. User Tips
- Battery Issues: If your device isn't charging or is almost dead, try a prolonged charge (over an hour), then unplug and hold the power button for 15 seconds. Repeat if necessary.
- Connectivity Problems: For update failures or Wi-Fi connection issues, especially with home networks, consider using a mobile hotspot. This often bypasses router firewall or network provider restrictions.
- VIN Recognition: If the automatic VIN scan fails, always try manual VIN input or manually select your vehicle's make, model, and year.
- Software Activation/Errors: If you encounter "registration failure" or "license exception" errors, ensure you're on a stable internet connection (mobile hotspot is often reliable). If issues persist, try re-downloading the software or contact VDIAGTOOL support.
- Diagnostic Reports: If you've shared a report but haven't received it via email, check your spam folder or whitelist the VDIAGTOOL sender email.
- Language Changes: To fully change the diagnostic program's language, you may need to contact VDIAGTOOL support for authorization and then download the specific language software.
11. Technical Specifications
| Item | Description/Specification |
|---|---|
| Display | 8 Inch Touch Screen, 1280x800 Resolution |
| Operating System | Android 10.0 |
| Processor | Quad-Core Processor 1.5GHz |
| Memory | 4G RAM, 64G ROM |
| Connectivity | Bluetooth 4.1, Wi-Fi (2.4GHz & 5Ghz), Type-C |
| Sensor | Gravity Accelerometer/Ambient Light Sensor |
| Audio | Microphone |
| Speaker | Built-In Speaker |
| Camera | 8 Mega Pixel |
| Battery | DC 7.3V Rechargeable Li-ion battery, 5000mAh |
| Tested Battery Life | 3.5 hours |
| Power Supply | Input: 5.0V 3.0A For AC Adapter Input: 100-240V Adapter Output: 5.0V 3.0A |
| Operating Voltage | 9V-36V |
| Dimensions | 10.39x6.06x1.39 in (264x154x35.5mm) |
| Weight (Including Battery) | 2.34lbs (1.06kg) |
| Gross Weight | 4.96lbs (2.25kg) |
| Operating Temp Range (Ambient) | 32°F ~ 104°F (0°C ~ 40°C) |
| Storage Temp (Ambient) | 14°F ~ 122°F (-10°C ~ 50°C) |
| Operating Humidity | <90% |
12. Warranty & Support
12.1 Limited Two Years Warranty
This warranty is expressly limited to the buyer who purchases the VDIAGTOOL VD80BT Lite product for purposes of resale or use in the ordinary course of business.
VDIAGTOOL VD80BT Lite is warranted against defects in materials and workmanship for two years (24 months) from the date of delivery to the buyer. This warranty does not cover any part that has been abused, altered, used for a purpose other than intended, or used in a manner inconsistent with instructions. The exclusive remedy for any defective tool is repair or replacement; VDIAGTOOL is not liable for any consequential or incidental damages.
12.2 Contact Us
For warranty and support, contact us:
- E-mail: support@vdiagtool.com
- Website: www.vdiagtool.com
- Phone: 1-213-355-7171 (United States)
For wholesale business or to become a distributor, contact us:
- E-mail: sales@vdiagtool.com
To invent with us, test products, or help make better products:
- E-mail: inventers@vdiagtool.com
To create social media content, post online, and help our community:
- E-mail: marketing@vdiagtool.com
12.3 Follow Us on Social Media
- Facebook Page: Search for "vdiagtool"
- Facebook User Group: Search for "VDIAGTOOL OFFICIAL User Group"
- Instagram: Search for "vdiagtool_official"
- TikTok: Search for "vdiagtool_us"
- YouTube: Search for "Vdiagtool Official"