1. Introduction
The Dymo LetraTag LT-100H is a portable label maker designed for home and office organization. It features an easy-to-use keyboard, a graphical display, and various formatting options to create custom labels quickly and efficiently.

Figure 1: Dymo LetraTag LT-100H Label Printer in use.
Key Features:
- Portable and handheld design
- Graphical display for previewing labels
- Multiple font styles, sizes, and border options
- Supports various LetraTag label tapes (paper, plastic, iron-on)
- Manual label cutting

Figure 2: Overview of Dymo LetraTag LT-100H features.
2. Setup
2.1 Unpacking
Carefully remove all components from the packaging. Ensure you have the following items:
- Dymo LetraTag LT-100H Label Printer
- Quick Start Guide (if included)
- Sample LetraTag Label Tape (if included)
- Storage Case (if purchased as a bundle)

Figure 3: Typical package contents.
2.2 Battery Installation
The LetraTag LT-100H requires four (4) AA alkaline batteries (not included).
- Locate the battery compartment cover on the back of the printer.
- Press down on the tab and slide the cover off.
- Insert four AA batteries, ensuring the correct polarity (+/-) as indicated inside the compartment.
- Replace the battery compartment cover by sliding it back until it clicks into place.

Figure 4: Battery installation.
2.3 Label Tape Installation
The LetraTag LT-100H uses Dymo LetraTag (LT) label cassettes.
- Open the label compartment cover. This is typically done by lifting the top part of the printer or pressing a release button.
- Insert the label cassette into the compartment with the label side facing down, ensuring it clicks firmly into place. The tape should feed smoothly into the printer mechanism.
- Close the label compartment cover.

Figure 5: Label tape compartment open for insertion.

Figure 6: Example of a Dymo LetraTag label tape cassette.
2.4 Powering On/Off
To turn the printer ON or OFF, press and hold the red ON/OFF button (usually located on the top left of the keyboard) for approximately 3 seconds until the screen illuminates or turns off.
3. Operating Instructions
Creating labels with your LetraTag LT-100H involves three main steps: adding tape, editing content, and printing.

Figure 7: The three-step printing process.
3.1 Entering Text
Use the QWERTY keyboard to type your desired text. The text will appear on the display screen as you type.
3.2 Formatting Labels
The LT-100H offers various formatting options to customize your labels:
- Print Styles: Choose from 7 different print styles.
- Font Sizes: Select from 5 available font sizes.
- Symbols: Access 195 built-in symbols and special characters.
- Border Styles: Apply 8 different border styles to your labels.
- Character Display: The display supports 13 characters at a time.
- Label Memory: Store up to 9 frequently used labels.
- Line Printing: Print up to 2 lines of text on a single label.
Use the "Settings" and "Format" buttons, along with the navigation arrows (up, down, left, right) and "OK" button, to access and apply these formatting options.

Figure 8: Label formatting options.
Extended Symbol Set:
The label maker supports a comprehensive set of symbols, including various currencies, mathematical symbols, punctuation, and decorative icons. Refer to the display or quick start guide for a full list.

Figure 9: Extended symbol set.
3.3 Printing Labels
Once your text is entered and formatted as desired, press the "PRINT" button. The label will be printed and dispensed from the front of the printer.
3.4 Cutting Labels
The LetraTag LT-100H features a manual cutter. After printing, use the cutter button (usually located on the side of the printer) to cleanly cut the label from the tape roll.
4. Maintenance
4.1 Cleaning the Printer
- Wipe the exterior of the printer with a soft, clean, damp cloth.
- Do not use abrasive cleaners, alcohol, or solvents, as these can damage the printer's surface.
- If print quality degrades, ensure the label tape is clean and free of dust.
4.2 Storage
- Store the printer in a cool, dry place away from direct sunlight and extreme temperatures.
- If the printer will not be used for an extended period, remove the batteries to prevent leakage and potential damage.
- Keep the printer in its protective case (if available) to prevent scratches and dust accumulation.
5. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Printer does not turn on | Dead or incorrectly inserted batteries | Replace batteries with new AA alkaline batteries, ensuring correct polarity. |
| No text prints / Blank label | Label cassette not installed correctly or empty | Ensure the label cassette is firmly seated. Replace with a new cassette if empty. |
| Poor print quality / Faint text | Low batteries; dirty print head; old or damaged tape | Replace batteries. Ensure tape is clean. Try a new label cassette. |
| Label jams | Incorrect tape installation; foreign object in tape path | Remove cassette, clear any obstructions, reinsert tape correctly. |
| Cutter not working | Tape jam; cutter mechanism obstructed | Clear any tape jams. Ensure nothing is blocking the cutter. |
6. Specifications
| Feature | Specification |
|---|---|
| Model | DYMO LetraTag LT-100H |
| Printer Color | Silver |
| Max. Label Width | 12 mm |
| Power Supply | 4 x AA Alkaline Batteries (not included) |
| Cutting Method | Manual |
| Display | LED Screen (Graphical) |
| Print Resolution | 203 DPI |
| Supported Tapes | Dymo LetraTag (LT) Paper, Plastic, Iron-On Fabric Tapes |
| Print Styles | 7 |
| Font Sizes | 5 |
| Symbols | 195 |
| Border Styles | 8 |
| Line Printing | Up to 2 lines |

Figure 10: Wide range of applications for LetraTag labels.
7. User Tips
- For best results and optimal print quality, always use genuine Dymo LetraTag label tapes.
- Ensure batteries are fresh and of good quality for consistent performance and clear, legible prints.
- When creating multi-line labels, use the preview function to ensure proper alignment and readability before printing.
- Keep the printer clean and free of dust, especially around the tape path, to prevent jams and maintain print quality.
8. Warranty and Support
For warranty information, please refer to the documentation provided with your purchase or contact your retailer. For technical support or further assistance, please contact the manufacturer or your point of purchase.
A user manual in PDF format may also be available for download from the manufacturer's official website or via the provided link: Dymo LetraTag LT-100H User Manual (PDF).