XOSS G2 / G2+

Contents

XOSS G+ G2 GPS Cycling Computer User Manual

Model: G2 / G2+

Brand: XOSS

Introduction

This manual provides comprehensive instructions for the XOSS G2 and G2+ GPS Cycling Computers. It covers device setup, operational procedures, maintenance guidelines, troubleshooting tips, detailed specifications, and warranty information. Please read this manual thoroughly to ensure proper use and optimal performance of your cycling computer.

XOSS G2 and G2+ models side-by-side, showing display differences

Figure 1: XOSS G2 and G2+ models comparison. The G2+ model offers a larger display and additional sensor connectivity.

Setup

Packing List

Ensure all items are present in the package:

  • XOSS G+ x 1 (Cycling Computer)
  • Cycling Computer Mount x 1
  • Type-C USB Cable x 1
  • Protection Rubber Pad x 1
  • Rubber Band x 2
  • User Manual x 1
XOSS G2+ with included accessories

Figure 2: XOSS G2+ and its standard accessories.

Installation

  1. Place the protection rubber pad on the back of the bike stand;
  2. Use a rubber band to secure the bracket to the handlebar or stem;
  3. Align the tabs on the back of the device with the grooves on the bike stand, press down slightly, and rotate the device 90 degrees until it locks into place.
Diagram showing the installation of the cycling computer mount and device on a handlebar

Figure 3: Installation steps for the XOSS G+ cycling computer on a bike handlebar.

ANT+ Sensor Connection (G2+ Model Only)

The G2+ model supports connection with Heart Rate, Cadence, and Speed sensors. It does not support connection with a power meter. Sensors must be purchased separately.

  1. Bring the device within 3 meters of your sensors, and ensure it is at least 10 meters away from other riders' sensors to avoid interference.
  2. Press both buttons simultaneously on the XOSS G+ until the sensor icon is flashing. This indicates the XOSS G+ is searching for active sensors nearby.
  3. If the pairing succeeds, the sensor icon will remain static. Press the right button again to enter the "Tire Circumference" setting interface.
Images showing SPD/CAD sensor being attached to crank arm and wheel hub, and a heart rate monitor on an arm, with Bluetooth and ANT+ icons

Figure 4: Examples of ANT+/BLE sensor installation and connection for Cadence, Speed, and Heart Rate.

Operation

Power On/Off and GPS Positioning

  1. Turn On: Long press the right button to turn on the device.
  2. Start GPS Search: Short press the left button to start searching for GPS. The GPS icon will appear and flash.
  3. Acquire GPS Signal: After startup, remain static for a few minutes to acquire a GPS signal. When the GPS icon stops flashing with a BEEP prompt, it indicates the device is ready.
  4. End Recording: Long press the left button to save the workout after ending the ride. The Bike Computer will then restore its initial interface.

Note: For optimal GPS signal acquisition, use the device in an open, barrier-free outdoor area. The device only supports outdoor recording.

XOSS G+ display showing GPS signal strength and other data

Figure 5: Device display during GPS signal acquisition.

Button Functions

  • Left Button:
    • Long Press: End recording
    • Short Press: Start / Pause / Resume
  • Right Button:
    • Long Press: Power on / Off
    • Short Press: Switch data display

Connect with XOSS App

The XOSS App allows for data synchronization, settings adjustments, and workout analysis.

  1. Search for "XOSS" in Google Play Store or Apple App Store, or scan the QR code below to download the XOSS App.
  2. Turn on your XOSS G+ device and ensure Bluetooth is enabled on your phone.
  3. Open the XOSS App, select "Devices" > "Bike Computers" > "G/G+".
  4. After connecting, you can access settings to change Backlight, Key Tone, Auto Pause, Speed Alert, Tire Circumference, Units, Time Zone, etc. Workout data will be automatically synced to the XOSS App.

Note: Long press the left button to end recording before connecting to the app. The App is designed for Bluetooth 4.0 or later versions.

Screenshots of the XOSS App interface, showing device connection, workout summary, and synchronization with Strava and TrainingPeaks

Figure 6: XOSS App interface for device management and data analysis.

QR code for downloading the XOSS App

Figure 7: QR Code for XOSS App download.

Custom Data Layout

You can customize the data displayed on your device screen via the XOSS App.

  1. Connect your G+ device to the XOSS App.
  2. Click "Data Layout".

Note: This feature requires firmware version 1.09 or later and XOSS app version Android 3.10.2 or later, or iOS 3.11.0 or later.

Detailed view of the G2+ display showing 10 data items on one page

Figure 8: Example of 10 data items displayed on one page.

Time Zone Setting in XOSS App

To ensure accurate timekeeping, set your time zone through the app:

  1. Connect your G+ device to the XOSS App.
  2. Click "Settings" > "User Profile" > "Time Zone". The device will sync with your phone's time zone.

Recordable Data Types

The device can record up to 24 types of data, including:

  • CLOCK (Current Time)
  • TEMP (Temperature)
  • SPD (Current Speed)
  • GRD (Grade)
  • HR (Current Heart Rate)
  • CAD (Current Cadence)
  • TIME (Moving Time)
  • DISTANCE (Distance)
  • CALORIE (Calories)
  • ELEVATION (Elevation)
  • AVG (Average Speed)
  • AVG (Average Heart Rate)
  • AVG (Average Cadence)
  • PAUSE (Paused Time)
  • GAIN (Elevation Gain)
  • VAM (Vertical Ascent in Metres)
  • LOSS (Elevation Loss)
  • MAX (Max Speed)
  • MAX (Max Heart Rate)
  • MAX (Max Cadence)
  • TOTAL (Total Time)
  • ODO (Odometer)
  • PWR(e) (Estimated Power)
  • MAX (Max Elevation)
Diagram illustrating various data points tracked by the computer

Figure 9: Overview of data points tracked by the XOSS G+ cycling computer.

Device Settings (Circumference, Units, Time Zone)

You can adjust these settings directly on the device:

  1. Tire Circumference Setting (mm):
    • Press the left button to set numbers.
    • Press the right button to switch position.
    • Long press the right button to move to the next step.
  2. Metric/Imperial Unit Setting:
    • Press the left button to switch units.
    • Long press the right button to move to the next step.
  3. Time Zone Setting:
    • Press the left button to switch numbers.
    • Press the right button to switch position.
    • Long press the right button to end setting.
Screenshots of device display for Tire Circumference, Metric/Imperial Unit, and Time Zone settings

Figure 10: Device interface for adjusting settings.

Product Feature Overview Video

Video 1: A short overview of the XOSS G2+ features, including screen display, auto backlight, SPD/CAD mode, ANT+/BLE sensor support, 3 GPS system, 28-hour battery life, and IPX7 waterproof rating.

Maintenance

Firmware Upgrade

It is recommended to keep your device's firmware updated for the best performance and features. When new firmware is available, the XOSS App will prompt you to update it.

Troubleshooting Tip: If you encounter issues during the firmware upgrade (e.g., device stuck in DFU mode), try toggling Bluetooth off and on again in your phone's settings, then reconnect the XOSS App to restart the upgrade.

Charging

The device uses a Type-C USB cable for charging. When charging, the battery icon in the upper right corner of the display will change from empty to full. Once there are three bars and the icon stops flashing, charging is complete.

Close-up of the Type-C charging port on the device

Figure 11: Type-C charging port.

Waterproof Rating

The XOSS G+ / G2+ cycling computer has an IPX7 waterproof rating, meaning it is protected against temporary immersion in water. This prevents water from entering the bike computer during rain or splashes.

Troubleshooting

  • GPS Signal Acquisition Issues:

    If the GPS icon continues to flash or you cannot acquire a signal, ensure you are in an open, outdoor area free from obstructions. Remain static for a few minutes after powering on to allow the device to lock onto satellites.

  • App Connection Problems:

    If the device fails to connect to the XOSS App, verify that Bluetooth is enabled on your phone and the device. Ensure the XOSS App is updated to the latest version (Android 3.10.2+ or iOS 3.11.0+). Try restarting both the device and the phone's Bluetooth.

  • Sensor Pairing Issues (G2+ Only):

    If ANT+ or BLE sensors are not pairing, ensure the sensors are active and within 3 meters of the G2+ device. Keep the device at least 10 meters away from other cycling computers or sensors to prevent interference. Press both buttons simultaneously on the G2+ to initiate sensor search.

  • Firmware Upgrade Failure:

    If the device gets stuck during a firmware upgrade, try turning your phone's Bluetooth off and then back on. Reconnect the XOSS App and attempt the firmware upgrade again.

  • Battery Not Charging:

    Ensure the Type-C USB cable is properly connected to both the device and a power source. Check if the battery icon on the display indicates charging. If not, try a different cable or power adapter.

Specifications

FeatureSpecification
Product NameXOSS G+ Smart GPS Cycling Computer
Model NumberXOSS G2 / G2+
Display Size2.2 inches
Dimensions71mm x 48mm x 19.1mm
Weight42g
Operating Temperature-10°C ~ 50°C
Battery500mAh Rechargeable Lithium Battery
Battery Life28 hours (can record 1500km of data)
Charging InterfaceType-C
Waterproof LevelIPX7
Wireless TransmissionBLE 5.0
ANT+ Sensor Support (G2+ only)Heart Rate Monitor, Speed Sensor, Cadence Sensor, Speed/Cadence Sensor
Barometric AltimeterYes
Auto PauseYes
Auto BacklightYes (Automatically lights up at night)
App SupportXOSS App
Third-party Platform SupportStrava, TrainingPeaks
Data Display Types24 Types
CertificationCE, FCC, RoHS

Warranty & Support

Warranty Information

The product comes with a one-year free warranty from the date of purchase. For warranty service, please contact your original dealer.

Conditions not covered by warranty:

  • Normal aging loss of the battery.
  • Damage and loss of products due to improper installation.
  • Damage caused by abnormal use, such as high temperature and water damage beyond IPX7 rating.
  • Damage caused by unauthorized dismantling or maintenance by personnel not approved by the manufacturer.

Support

For more product information and support, please visit:

A PDF version of the user manual is also available for download: XOSS G+ User Manual (PDF)

User Tips

  • For accurate GPS tracking, always ensure you are in an open outdoor environment when starting your ride.
  • Remember the key difference between models: the G2+ supports external ANT+/BLE sensors (heart rate, cadence, speed), while the G2 does not. Ensure you have the correct model if you plan to use external sensors.
  • External sensors (like heart rate monitors or speed/cadence sensors) are typically sold separately.
  • When connecting to the XOSS App, make sure to end any active recording on the device by long-pressing the left button before attempting to connect.
  • Keep your device firmware and XOSS App updated to benefit from the latest features and bug fixes.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.