BAOFENG DM-1702

Contents

Baofeng DMR DM-1702 Digital Walkie Talkie User Manual

Model: DM-1702

Baofeng DM-1702 Digital Walkie Talkie

Your guide to operating and maintaining your Baofeng DM-1702.

1. Introduction

Thank you for choosing the Baofeng DM-1702 Digital Walkie Talkie. This device is designed for high-performance and stable radio communication, featuring DMR dual-slot digital technology, 3000 memory channels, a full-color LCD display, and a full keyboard for hand-tuning. This manual provides detailed instructions for understanding its features, operation, and maintenance.

Main Features

  • Broadband Walkie Talkie: Supports UV dual segment (UHF 400-480MHz / VHF 136-174MHz).
  • DMO True2-Slot Dual Time Slot: Achieves two groups of calls simultaneously on one frequency, doubling communication efficiency.
  • Digital and Analog Compatible: Seamless transition from analog to digital communication modes.
  • Digital Signaling Function: Supports DMR protocol with single, group, and all call modes, including remote inhibit.
  • SMS Function: Text editing and drafting in 64 characters (Chinese/English) for convenient messaging.
  • High Sound Quality: Utilizes advanced AMBE +2TM voice processing technology.
  • Manual Writing-Frequency: Supports channel/frequency mode manual tuning and software-based frequency setting.
  • High/Low Power Switch: Adjustable power output for different call distances to conserve energy.
  • Alarm Function: General and silent alarm support for emergency situations.
  • Digital Mode Relay Support: Compatible with relay use in digital mode.
  • Customizable Side Buttons: Side buttons can be programmed without altering user operating habits.

2. Safety and Overview

RF Radiation Information

This product is intended for professional applications meeting RF radiation requirements. Users must be aware of RF radiation hazards and take appropriate measures to meet radiation limits.

Common Sense in RF Radiation

RF refers to electromagnetic frequencies radiated into space, used in communication, medical treatment, and food processing. The device will produce some RF radiation during use.

Control and Operating Instructions of RF Radiation

To maximize performance and ensure compliance with radiation limits in occupational/controlled environments, transmission time should not exceed 50% of the rated factor. Follow these instructions:

  • RF radiation is generated only during transmission (speech), not during reception (listening) or standby.
  • Maintain a distance of at least 2.5 cm between the terminal and your body during transmission.

3. Setup

3.1. Preparation Before Use

Charging the Battery

CAUTION:

Ensure the product is OFF when charging. If the battery indicator flashes red constantly, the battery power is too low. The charger will initiate a pre-charge process for approximately 30 seconds before normal charging begins (solid red light).

Use only the specified charging cradle. The charging cradle indicator shows the charging status:

  1. Plug the power adapter into a power outlet.
  2. Plug the other end of the power adapter into the socket on the back of the charging cradle.
  3. Insert the battery or the battery-equipped product into the charging cradle correctly.
Charging Status Indicators
Indicator DisplayCurrent Charge Status
Red light flashesBattery power is too low
Red lightIn charging
Green lightThe charging is completed

Note: For best battery performance, charge for a minimum of 4 hours on first use.

3.2. Battery Information

First Use of the Battery

The battery is not fully charged at the factory. Charge the new battery for 4 hours before first use. For optimal performance, repeat this charging cycle for the first three uses. Recharge when battery power is low.

Suitable Battery Type

Use only the specified battery for charging. Using other batteries may cause explosion or injury.

Battery Safety Attention

  • Do not allow metal contacts (coins, keys, jewelry) to touch battery contacts or pole pieces to prevent short circuits, discharge, heat, or leakage.
  • Do not short-circuit battery terminals or discard the battery in fire. Do not disassemble the battery pack.
  • Dispose of batteries in a dedicated battery recycling box.

Battery Normal Operation Instructions

  • Charge the battery indoors at room temperature.
  • When the charger indicator turns from red to green, the battery is fully charged and can be removed.
  • You can charge the battery while it's installed in the walkie-talkie, but it's best to turn off the device to ensure a full charge.
  • Do not charge the battery if it's not depleted; this shortens battery life.
  • Do not "power up" a fully charged battery on the charger again; this significantly reduces cycle life.
  • Battery performance reduces below -20°C. Prepare backup batteries for cold weather. Cold batteries that don't work may recover at room temperature.
  • Wipe battery contacts with a clean, dry cloth before inserting to prevent poor contact.

Battery Storage Needs

  • For long-term storage, fully charge the battery to prevent over-discharge.
  • Recharge stored batteries approximately every 6 months to prevent electrolyte damage.
  • Store batteries at room temperature in a cool, dry place to minimize self-discharge.

Battery Voltage & Power Indication

If configured, press and hold the battery power prompt shortcut key to check remaining power via LED indicator, tone, and battery icon. The top right of the screen displays the current battery power icon:

Battery Power Icons
Battery IconBattery Power
[Full Icon]High
[3/4 Icon]Medium
[1/2 Icon]Low
[Empty Icon]Insufficient

3.3. Accessories Installation

Install/Remove the Antenna

  1. Turn off the radio.
  2. Insert the antenna into the mounting hole and turn clockwise to install.
  3. To remove, turn the antenna counterclockwise.

CAUTION:

Do not shake the top of the antenna by hand, as this may reduce performance and service life.

Install/Remove the Battery

Install: Align the battery with the holder on the back, push firmly, and slide up until it locks.

Remove: Turn off the transceiver. Slide the battery latch to the unlocked position, hold, and slide the battery downward and out.

Install/Remove the Belt Clip

Install: Unscrew the two screws on the battery. Align the belt clip with the screw holes on the top of the battery, and tighten the screws.

Remove: Loosen and remove the screw from the belt clip (it's recommended to screw it back to the battery for storage).

Install External Headphones/Microphone (Optional)

Open the headset cover, plug the headset into the hole. When not in use, unplug and cover the earphone cap. Always cover the dust cover when not using the universal interface.

3.4. Status Indication

LED Indicators

The LED indicator helps you easily understand the current operating state:

  • Red on: Transmitting
  • Green on: Receiving
  • Green flash: Scanning

LCD Icons Description

LCD Display Icons
Icon NameIconDescription of Product Status
Signal Strength[Bars]More bars = stronger signal
Transmission PowerH/M/LH: High, M: Middle, L: Low power transmission
Speaker[Speaker Icon]Speaker enabled, reception effective
Frequency Bias+Transmission frequency is reception frequency + bias (positive)
Relay Mode-Transmission frequency is reception frequency - bias (negative)
Offline State[Offline Icon]Currently in offline state
Scan[Scan Icon]Scan is on and in normal mode
Battery Power[Battery Bars]More bars = more battery power
Pointer[Arrow]Points to main digital mode; A/B button switches main channel. Double-waiting in digital sub-channel shows [Icon].

3.5. Function Key Analysis

The Baofeng DM-1702 features a comprehensive set of buttons and controls for various functions. Refer to the diagram and table below for a detailed understanding.

Baofeng DM-1702 Function Key Analysis Diagram

Diagram Description: This image shows the front, side, and top views of the Baofeng DM-1702 walkie-talkie, highlighting the location of each function key and component. Key labels include: Volume knob, LED flashlight, Side key one, PTT Emission key, Side key two, Menu keys, Keypad, Antenna, SOS key, Speaker, Headphone jack, Type-C interface, LCD display screen, Back key.

Description of Buttons

Button Functions
ButtonDescription
[PTT] TransmitSwitches between transmission and reception. Press to transmit, release to receive.
Side button 1Short press: Quickly switch upper/lower screen. Press & hold: Enter/exit alarm mode.
Side button 2Short press: Shortcut select channel up. Press & hold: Turn on monitor (analog channels only).
Side button 3Short press: Shortcut select channel down. Long press: Power switch, select high/low power.
0-9 Number Buttons0-9 code words in DTMF. Select punctuation/letters in Pinyin. Press & hold: Jump to contact (if numeric shortcut set).
[MENU] ButtonActivates menu mode, selects menu items. Press & hold: Enter radio settings.
[Up Arrow] ButtonMove up, change scanning direction, move left in SMS editing.
[Down Arrow] ButtonMove down, change scanning direction, move right in SMS editing.
[Exit]/[Clear] ButtonClears entered info. Press & hold: Switch channel/frequency mode.
[*] ButtonPress & hold: Lock on/off keyboard. Code word * in DTMF.
[#] ButtonCode word # in DTMF. Switch input method.

Programmable Buttons

For operational convenience, keys like SK1, SK2, SK3, P1, and P2 are programmable. Consult your distributor for specific functions. Refer to the "Function and Operation" section for detailed descriptions.

Programmable Button Shortcuts
No.Shortcut NamePurpose
1NoneNo function assigned.
2All prompt tone on/offEnable/disable all prompt tones.
3Emergency mode onQuickly establish emergency call (recommended for orange button).
4Emergency mode offQuickly end outward emergency call.
5Select high/low powerQuickly switch between high/low power.
6MonitorQuickly turn on/off monitor function.
7Push to talk 1Quickly make digital group/single calls, call prompts, send text messages (digital mode only).
8Relay/offlineQuickly switch between relay/offline mode.
9Scan on/offQuickly turn scan function on/off (double-segment double-waiting scan not supported).
10Strict/normal squelchQuickly switch between strict/normal squelch (analog mode only).
11Encryption on/offQuickly turn on/off encryption for channel (digital mode only).
12Voice control on/offQuickly turn on/off voice control function.
13Area switchingQuickly select area, allowing user to switch between two areas.
14Battery power indicationQuickly access battery power status (Green: sufficient, Yellow: available, Red: low).
15Individual operation switchQuickly turn on/off individual operation function.
16Recording switch(Firmware-based) Quickly turn on/off recording.
17Record playback(Firmware-based) Quickly playback recordings.
18Delete all the recordings(Firmware-based) Quickly delete all recordings.
191750HzFast launch 1750 pilot signal.
20Up and down screen switchQuickly switch upper/lower screen.
21Left key(Function not detailed in source)
22Right key(Function not detailed in source)

Note: The same button can have different functions for short press and long press, as configured by dealer settings.

4. Operating Instructions

4.1. Basic Operation

Power On and Off

To Power On: Turn the [Power Switch / Volume Control] knob clockwise until you hear a "click" and a short beep. (English version supports channel number broadcast).

To Power Off: Turn the knob counterclockwise until you hear a "click".

Note: If tone function is disabled (Menu -> Settings -> Walkie talkie Settings -> Tones / Tips -> All Tones -> off), there will be no boot tone. If all LEDs are disabled, the transmit/receive light will not come on during power-up, but a short beep indicates successful boot detection.

Volume Adjustment

Turn the [Power Switch / Volume Control] knob clockwise to increase volume, counterclockwise to decrease. The LCD displays a volume bar.

Transmit and Receive

Selecting Region

A region is a channel group (up to 250 regions, each with up to 64 channels) for managing channels with similar attributes. Select a region:

  • Via Menu: "MENU" -> "Region" -> "Region list", use [Up/Down] to select, then [MENU] to switch.
  • Via Programming Button: If the dealer set a [Regional switch] shortcut, press it to switch.
Adding a Region

If needed, add a new region: "Menu" -> "Area" -> "New Area", press [MENU], input the name, then [MENU] to save.

Digital and Analog Channel Switch

Each channel can be configured as analog or digital. If the current region contains both, you can switch between them.

VFO Frequency Mode Frequency Setting

In frequency mode, long press [BACK] on standby. "V" on the screen indicates manual input frequency mode. Manually input frequency and specify for transmission.

Select via Menu: "Menu" -> "Settings" -> "Walkie talkie Settings" -> "Mode" -> "Frequency Mode", then [MENU] to set.

Frequency Selecting: Use [Up/Down] or directly enter frequency using numeric keys (0-9). MHZ for first three digits after decimal, KHZ for fifth digit.

CAUTION:

Write frequency software configuration path: open software -> Edit -> VFO mode -> VFO A -> digital/analog data -> channel mode -> select "number." Or set VFO B to Analog. Normally set VFO A to digital mode and VFO B to analog mode.

Single/Dual Band Mode Switch

On standby, press [Up/Down] to switch primary/secondary channels.

  1. Black pointer "D" indicates primary digital channel.
  2. Black pointer "A" indicates primary analog channel.
  3. Press [BACK] to switch between dual band single standby or dual band dual standby.

If sub-channel is displayed, it's "dual band single standby" mode, and sub-channel doesn't receive signal. ARTS Auxiliary function doesn't work in dual keep mode (primary/secondary channel scanning, DTMF, auto-scan, work alone).

Select Channel, User ID, Group Call ID

After power on, if multiple regions exist, select desired region and turn Channel knob to select channel, user alias/ID, or group alias/ID.

Receive and Reply Group Calls

To receive a group call, transceiver must be configured to belong to the talk group. When receiving:

  • LED is green.
  • Screen shows RSSI, group alias, caller ID, and group call icon (digital only).
  • Hold walkie-talkie upright (1-2 inches from mouth).
  • Press [PTT] to reply (LED red).
  • Release [PTT] to answer.
  • Call terminates if no voice activity for scheduled time.

If not at home, it remains on current screen until answered. Press [BACK] to main screen to view caller's alias before reply.

Receive and Reply Single Call

Individual call to another walkie-talkie. Two types: presence test before call, or immediate call. When receiving:

  • LED is green.
  • Screen shows RSSI, single call with user's alias/ID, and one-way icon (digital only).
  • Hold walkie-talkie upright (1-2 inches from mouth). If "Channel Idle Tone" enabled, short beep indicates channel free.
  • Press [PTT] to reply (LED red).
  • Release [PTT] to answer.
  • Call terminates if no voice activity for scheduled time.
  • Short tone, screen shows call ended.
Receive All Call

Individual call to all walkie-talkies on channel for important notices. When receiving:

  • LED is green.
  • Screen shows RSSI, "All call" with user's alias/ID, and all call icon (digital only).
  • After call, returns to previous screen. If "channel idle tone" enabled, short beep indicates channel ready, cannot reply.

If you switch channels during an all call, transceiver stops receiving. Cannot use preprogrammed keys until call ends.

Start a Walkie-Talkie Call

Choose channel, user ID, or talk group via:

  • Channel knob
  • Pre-programmed one-touch call button
  • Address book list
  • Manual Dialing (via Contacts - single calling only, using keypad)
Using the Channel Knob to Place a Call

Initiate Group Call: Transceiver must belong to talk group. Rotate channel knob to select channel with active talk group alias/ID.

  1. Hold walkie-talkie upright (1-2 inches from mouth).
  2. Press [PTT] to initiate (LED red). Screen shows talk group alias/ID and group call icon.
  3. Release [PTT] to answer. When target replies, LED green. Screen shows group call icon, alias/ID, and walkie-talkie alias/ID.
  4. If "Channel Idle Tone" enabled, short beep indicates channel free. Press [PTT] to answer. Call terminates if no voice activity for scheduled time.
  5. Returns to screen before receiving. Can also initiate group call from address book.

Start a Single Call: Rotate channel knob to select channel with active user alias/ID.

  1. Hold walkie-talkie upright (1-2 inches from mouth).
  2. Press [PTT] to initiate (LED red). Screen shows RSSI, single call, user alias/ID, and one-way icon (digital only).
  3. Release [PTT] to answer. When target replies, LED green.
  4. If "Channel Idle Tone" enabled, short beep indicates channel free. Press [PTT] to answer. Call terminates if no voice activity for scheduled time.
  5. Short tone, screen shows call ended.

Can also initiate via one-touch address book or quick contact access via keypad.

Initiate All Call: Signals all users on channel (must be programmed). Rotate channel knob to select channel with active full call group alias/ID.

  1. Hold walkie-talkie upright (1-2 inches from mouth).
  2. Press [PTT] to initiate (LED red). Screen shows all-call group alias/ID and all-call icon.

CAUTION:

Channel users cannot reply to all calls.

Using the One-Touch Call Button

Assign one-touch call keys (short or long press) to predefined aliases/IDs for group or single calls.

  1. Press preprogrammed one-touch call button to initiate.
  2. Hold walkie-talkie upright (1-2 inches from mouth).
  3. Press [PTT] to initiate (LED red). Screen shows talk group/user alias/ID and call icon.
  4. Release [PTT] to answer. When target replies, LED green.
  5. If "Channel Idle Tone" enabled, short beep indicates channel free. Press [PTT] to answer. Call terminates if no voice activity for scheduled time.
  6. Returns to screen before receiving.
Analog Channel Call

On analog channel, hold [PTT] and speak to transmit. Release [PTT] to receive.

DTMF Call

Make a Call:

  • Under analog channel, press & hold [PTT] and press keypad number key.
  • Under analog channel, long press [#] to manual dialing mode, enter number, short press [PTT] to start DTMF call.

Receive Calls: If host computer configured DTMF as receiving signaling system, and decodes personal ID code, it's successful. During resetting time, can talk. Reset time requires re-decoding.

One-Touch Call (Analog Mode): Program radio's one-touch calls function:

  1. Enter DTMF number in DTMF Signaling -> Coding -> Coding Sequence.
  2. Programmable Button -> One Touch Access -> Mode -> (Analog) -> SMS / Code -> (Select code number).
  3. (Programmable key) -> Walkie-talkie button -> Side key X -> Push to talk X -> (Select PTT serial number).

After configuration, press side button for one-touch DTMF launch.

PTT ID Call

Make a Call: In analog mode, program radio for DTMF on-line/off-line code and enable up-down-line code on analog channel. Code sent when [PTT] pressed, released when [PTT] released.

4.2. Emergency Alarm Function

In emergencies, use this feature to request help. Emergency alarm has highest priority, works whether transmitting or receiving.

CAUTION:

To exit alarm mode: turn off radio (whole machine alarm) or temporarily exit (current channel alarm, continues if channel reselected).

Alarm function must be enabled by dealer (program path: Edit -> Digital Emergency Alarm System -> Emergency Alarm System -> System1). Understand concepts below before use.

Alarm Type

Alarm Types and Descriptions
Alarm TypeDescription
DisableAlarm function off, but can receive alerts.
ConventionalAudible and visual prompt.
SilentNo audible/visual prompt, no sound on received audio.
Silence with voiceNo audible/visual prompt, but sounds when [PTT] pressed for call/response.

Alarm Mode

Except "Disable", other alarm types support various modes (e.g., Conventional alarm type):

Alarm Modes and Descriptions
Alarm ModeDescription
Emergency alarmPress & hold [Emergency mode on] to send alarm tone; cannot talk.
Emergency alarm and call (alarm call)Press & hold [Emergency mode on] to send alarm tone, then [PTT] to speak (voice & background sent).
Emergency alarm and voice (emergency call)Press & hold [Emergency mode on] to enter alarm transmission channel; "emergency microphone" activates automatically (no [PTT] hold); voice & background sent.

Receive Emergency Alert

  • Screen alternates between number of alerts, alert received, and sender's alias/ID.
  • Beep sounds, LED flashes red.
  • If enabled, transceiver auto-acknowledges. Screen prompts "emergency alert received" until acknowledged/mode exits. Cannot receive other prompts/calls until exit.

Reply to Emergency Alert

When receiving an emergency alert:

  • Press any key to stop audible alerts.
  • Hold walkie-talkie upright (1-2 inches from mouth). If "channel idle tone" enabled, short beep indicates channel ready.
  • Press [PTT] to start emergency call (LED red).
  • Release [PTT] to answer. When emergency call initiates reply, LED green. Shows group call icons, talk group IDs, walkie-talkie ID.
  • When call finished, press [BACK] briefly, then Preset Alarm Off key to clear prompts and exit.
  • Returns to home screen.

Send Emergency Alert

Sends a non-voice signal, triggering a prompt on another transceiver.

  • Press preprogrammed alarm on button.
  • Screen shows "Send Alert", alternating with walkie-talkie ID. LED red, emergency call icon on home screen.
  • When confirmation received, emergency call tone sounds, LED flashes green. Screen shows successful.
  • If no confirmation after retries, beep sounds, screen shows failed.
  • Exits emergency alert mode, returns to home screen. If "silent", no voice/visual cues.

Send Emergency Alert with Call

Sends alert, then communicates via pre-programmed emergency channel after confirmation.

  • Press preprogrammed alarm on button.
  • Screen shows "Send Alert", alternating with walkie-talkie ID. LED red, emergency call icon on home screen.
  • When confirmation received, emergency call tone sounds, LED flashes green. Screen shows successful.
  • Hold walkie-talkie upright (1-2 inches from mouth).
  • Press [PTT] to initiate call (LED red, group icon appears).
  • Release [PTT] to answer.
  • If "Channel Idle Tone" enabled, short beep indicates channel free. Press [PTT] to answer.

Send Emergency Alert with Voice Follow

Sends alert, then microphone activates automatically ("Emergency Microphone") for hands-free communication. Ignores [PTT] press during preprogrammed emergency microphone launch.

CAUTION:

If [PTT] pressed during emergency microphone and held, transceiver continues firing until [PTT] released.

  • Press preprogrammed alarm on button.
  • Screen shows "send an alert", LED red, emergency call icon.
  • After successful alert, speak clearly. Transceiver auto-transmits without [PTT] until emergency microphone time ends.
  • While transmitting, LED red, emergency call icon.
  • After duration, auto-stops transmitting. Press [PTT] to launch again.

If "silent", no voice/visual cues. No response until emergency microphone period ends and [PTT] pressed. Prompts appear only when [PTT] pressed.

If alert request fails, returns to home screen.

Restart Emergency Mode

Occurs in two situations:

  • If transceiver in emergency mode changes channel, it exits. If alert activated on new channel, it resumes.
  • Press preprogrammed alarm on key in emergency call start/transmit state. Exits status, restarts.

Exit Emergency Mode

Transceiver exits when one of these occurs:

  • Receive emergency alert confirmation (alerts only).
  • Number of major attempts to send alert reached.
  • Press Preprogrammed Alarm Off.
  • Press [PTT].

4.3. Individual Operation

Ideal for lone workers. If no operation within preset time, radio automatically sends alarm to partner/control center.

Turn On: Via writing frequency software at startup, or press preset [Individual Operation] shortcut.

Operation: If no operation within preset response time, radio prompts. End prompt with physical operation (knob/button). If response time expires, radio activates alarm system.

Turn Off: Via writing frequency software, or press preset [Individual Operation] shortcut again.

Note: If not turned off before shutdown, function remains active next power-on.

4.4. Menu Operation

Menu Navigation

Press [MENU] in digital/analog mode to enter main menu. Use [Up/Down] to navigate submenus/options, [MENU] to confirm. Menu structure is configurable by dealer. This document describes menu item order. Example: Contacts -> Contacts List. Menu auto-resets to standby if no operation within preprogrammed time (configurable by dealer).

Input Method

Enter user aliases, numbers, text messages via keypad. Supports English, Simplified Chinese Pinyin, and number input.

CAUTION:

When inputting alias/ID/SMS, if editing area is empty, [BACK] returns to last menu. If content exists, [BACK] deletes character. [BACK] returns to last menu when no editing area exists.

English Input Method
  1. Press [#] to switch (ABC/abc).
  2. Press number buttons repeatedly for desired letter.
Keypad Characters (English)
KeyCharacters
11?!@&%*#
2abc2ABC
3def3DEF
4ghi4GHI
5jkl5JKL
6mno6MNO
7pqrs7PQRS
8tuv8TUV
9wxyz9WXYZ
00, blank
**
#Switch input mode
Simplified Chinese Pinyin Input Method
  1. Press [#] to switch (LCD shows PY).
  2. Press number buttons for pinyin; LCD shows alternate pinyin and candidate Chinese characters.
  3. Press [Up/Down] to select pinyin.
  4. Press [MENU] to move highlight to character area, [Up/Down] to select character.
  5. Press [MENU] to enter character. Repeat. Press [*] to input *.
Number Input Method
  1. Press [#] to switch (LCD shows 123).
  2. Press 0-9 for number. Press [*] to input *.
Input Special Characters

Press [1] for punctuation/special characters. Press [0] for space. In text display, [Up/Down] moves cursor left/right.

How to Use the Menu
  1. Press [MENU] to enter menu mode, then [Up/Down] to access menu function.
  2. Press [MENU] to select function or enter sub-menu.
  3. Press [BACK] to return to last menu.

CAUTION:

Transceiver auto-exits menu to main screen after inactivity (hang time set by programming software).

Push-to-Call

Set [Push-to-call] shortcut, press it to initiate operation. Categories:

  • Digital Channels: For group call contacts, initiate group call or send text. For single call contacts, initiate single call, send text, or application functions (call prompt, radio detection, remote monitor, activation, remote inhibit).

Call Prompt

In digital mode, send call prompt to contact; other party can call back directly.

Initiate: Select single call contact (Menu -> Contacts -> [Up/Down] to select -> Call prompt), or press [*] on main interface, enter number, select "Call prompt", [MENU] to start. Displays "successful" or "failed".

Receive: After receiving, tone rings (if enabled for caller's contact) and stays on display. Press [EXIT] to exit.

Radio Detection

In digital mode, initiate radio detection to contact to confirm if they are on/using current channel, without interference.

Initiate: Select single call contact (Menu -> Contacts -> [Up/Down] to select -> Radio detection), or press [*] on main interface, enter number, select "Radio detection", [MENU] to start. Displays "successful" or "failed". If successful, press [PTT] to call.

Receive: Auto-reply after receiving.

Remote Monitoring

In digital mode, remotely activate contact's microphone to monitor voice/background sound.

Initiate: Select single call contact (Menu -> Contacts -> [Up/Down] to select -> Remote monitor), or press [*] on main interface, enter number, select "Remote monitor", [MENU] to start. Displays "successful" or "failed". If successful, monitor background sound/voice.

Receive: Auto-transmits voice/background sound after receiving, exits when transmission time up. (Function works only if set by writing-frequency software).

Radio Activation

In digital mode, send activation command to contact to resume normal use.

Initiate: Select single call contact (Menu -> Contacts -> [Up/Down] to select -> Radio activation), or press [*] on main interface, enter number, select "Radio activation", [MENU] to start. Displays "successful" or "failed".

Receive: Sends activation tone, re-shuts down, then boots. Can also be activated by writing frequency software. (Function works only if set by writing-frequency software).

Radio Remote Kill

In digital mode, send remote inhibit command to contact to disable radio.

Initiate: Select single call contact (Menu -> Contacts -> [Up/Down] to select -> Radio inhibit), or press [*] on main interface, enter number, select "Radio inhibit", [MENU] to start. Displays "successful" or "failed".

Receive: Sends inhibit prompt tone, [PTT] displays "Transmission failed and inhibited". Can be activated by SMS writing frequency or wake-up.

Contact List Settings

Provides "Address Book" for walkie-talkies. Each entry (alias/ID) initiates call (group, single, all). Shows call type, alias, ID. Add, delete, edit contacts.

Group Call from Contact Lists:

  1. [MENU] to menu.
  2. [Up/Down] to contact list, [MENU] to select (alphabetical).
  3. [Up/Down] to desired group name/ID.
  4. Hold walkie-talkie upright (1-2 inches from mouth).
  5. [PTT] to initiate (LED red). Screen shows talk group alias/ID and group call icon.
  6. Release [PTT] to receive. When user responds, LED green. Shows group call icon, user ID.
  7. If "Channel Idle Tone" enabled, short beep indicates channel free. Press [PTT] to answer. Call terminates if no voice activity for scheduled time.

Single Call from Contact List:

  1. [MENU] to menu.
  2. [Up/Down] to contact list, [MENU] to select (alphabetical).
  3. [Up/Down] to desired user alias/ID. Or [Up/Down] to dial manually, [MENU] to select. If ID dialed previously, it's displayed with blinking cursor for editing. Or [Up/Down] to dial manually, [MENU] to select, use keypad for new ID.
  4. Hold walkie-talkie upright (1-2 inches from mouth).
  5. [PTT] to initiate (LED red). Screen shows user alias/ID, single and single call icons.
  6. Release [PTT] to answer. When radio responds, LED green. Screen shows transmitting user ID.
  7. If "Channel Idle Tone" enabled, short beep indicates channel free. Press [PTT] to answer. Call terminates if no voice activity for scheduled time.
  8. Short tone, screen shows call termination.

Call Log

Records all dialed, picked-up, and missed calls. Use to view and manage recent calls.

Check Latest Call Number: Menu has missed, received, dialed calls.

  1. [MENU] to menu.
  2. [Up/Down] to call record, [MENU] to select.
  3. [Up/Down] to desired list, [MENU] to select.
  4. Screen shows recent entries (top of list).
  5. [Up/Down] to view list, [PTT] to start call with selected alias/ID.

Missed Call Screen: Displays "missed call" message. View or check later. If [PTT] pressed while viewing, radio exits screen and establishes one-way call.

  1. Screen shows "Missed Calls", "Missed Calls", "View".
  2. [MENU] to check missed call ID. List displayed. [MENU] to save/delete, or [Up/Down] to check later, [MENU] to select and return to main screen.

Store Alias/ID from Missed Calls:

  1. [MENU] to menu.
  2. [Up/Down] to call record, [MENU] to select.
  3. [Up/Down] to missed call, [MENU] to select.
  4. [Up/Down] to missed call alias/ID, [MENU] to select.
  5. [Up/Down] to save, [MENU] to select.
  6. Blinking cursor appears, enter alias if needed, [MENU].
  7. Screen shows contact saved. (Can also enter alias ID).

Delete Call in Call List:

  1. [MENU] to menu.
  2. [Up/Down] to call record, [MENU] to select.
  3. [Up/Down] to desired list, [MENU] to select.
  4. [Up/Down] to desired alias/ID, [MENU] to select.
  5. [Up/Down] to "delete the entry?", [MENU] to select.
  6. Select "Yes" to delete ([MENU]). Entry appears. Or "No" ([MENU]) to return.

If call list is empty, screen displays blank list. Bass tone if keyboard tone on.

Calling Prompt Operation

Call Alert prompts specific walkie-talkie user to call back. Only for user aliases/IDs, via Contacts or Manual Dialing.

Receive and Confirm: Screen displays "call alert", alternating with alias/ID. Repeat tone, LED flashes red. Press [PTT] to confirm, or [MENU] to "Ignore?".

Initiate from Communication List:

  1. [MENU] to menu.
  2. [Up/Down] to address book, [MENU] to select.
  3. [Up/Down] to desired alias/ID, [MENU]. Or [Up/Down] to dial manually, [MENU] to select, input user ID, [MENU].
  4. [Up/Down] to call prompt, screen shows "call prompt: <User alias or ID>", [MENU] to send.
  5. When sent, LED red.
  6. If confirmation received, tone sounds, alert appears. If no confirmation, beep sounds, "call alert failure".

SMS Function

Supports DMR data function, sending/receiving messages (max 144 characters, max 50 lines).

Edit and Send Messages (Menu):

  1. [MENU] to menu.
  2. [Up/Down] to "SMS", [MENU].
  3. [Up/Down] to "Write SMS", [MENU].
  4. Blinking cursor, input SMS via keyboard. [Up] moves left, [Down] moves right. [BACK] deletes character. If no content, [BACK] returns to upper menu.
  5. After SMS, [MENU] to send/save.
  6. When editing, [MENU] to clear options/content, returns to upper menu.
  7. After send, [Up/Down] to name/ID, [MENU]. Or [Up/Down] to Manual Dialing, [MENU], input user ID, [MENU].
  8. LCD shows "SMS :< User/Call group alias or ID>", confirms sending.
  9. If successful, beep, screen shows "sent". If failed, high-pitched tone, screen shows "failed". Returns to re-send screen.

Send Prefabricated SMS: Supports up to 50 predefined SMS (programmed by agent). Can edit before sending.

  1. [MENU] to menu.
  2. [Up/Down] to "SMS", [MENU].
  3. [Up/Down] to "Prefabricated SMS", [MENU].
  4. [Up/Down] to desired SMS, [MENU].
  5. Blinking cursor, input SMS via keyboard. [Up] moves left, [Down] moves right. [BACK] deletes character. If no content, [BACK] returns to upper menu.
  6. After SMS, [MENU] to send/save.
  7. When editing, [MENU] to clear options/content, returns to upper menu.
  8. After send, [Up/Down] to name/ID, [MENU]. Or [Up/Down] to Manual Dialing, [MENU], input user ID, [MENU].
  9. LCD shows "SMS :< User/Call group alias or ID>", confirms sending.
  10. If successful, beep, screen shows "sent". If failed, high-pitched tone, screen shows "failed". Returns to re-send screen.

Use One-Touch Call Button to Send Prefabricated SMS:

  1. Press pre-programmed one-touch call; sends to predefined alias/ID.
  2. LCD shows "SMS :< User/Call group alias or ID>", confirms sending.
  3. If successful, beep, screen shows "sent". If failed, high-pitched tone, screen shows "failed". Returns to re-send screen.

Manage Failed SMS: In re-send screen, options: Re-send, Forward, Edit.

Re-send SMS:

  1. [MENU] to re-send same SMS to same user/group.
  2. If successful, beep, screen shows "sent". If failed, high-pitched tone, screen shows "failed".

Forward SMS: Sends to another user/group.

  1. [Up/Down] to "Forward", [MENU].
  2. [Up/Down] to required alias/ID, [MENU]. Or [Up/Down] to Manual Dialing, [MENU], input user ID, [MENU].
  3. LCD shows "SMS :< User/Call group alias or ID>", confirms sending.
  4. If successful, beep, screen shows "sent". If failed, high-pitched tone, screen shows "failed".

Edit SMS: Writes SMS before sending.

CAUTION:

Cannot edit subject line of SMS received from Email program.

  1. [Up/Down] to "Edit", [MENU].
  2. Blinking cursor, input SMS via keyboard. [Up] moves left, [Down] moves right. [BACK] deletes character. If no content, [BACK] returns to upper menu.
  3. After SMS, [MENU] to send/save.
  4. When editing, [MENU] to clear options/content, returns to upper menu.
  5. After send, [Up/Down] to name/ID, [MENU]. Or [Up/Down] to Manual Dialing, [MENU], input user ID, [MENU].
  6. LCD shows "SMS :< User/Call group alias or ID>", confirms sending.
  7. If successful, beep, screen shows "sent". If failed, high-pitched tone, screen shows "failed".

Manage Already Sent SMS: Saved to "Sent item" (max 50). New SMS updates record. [BACK] returns to previous screen.

Read Already Sent SMS:

  1. [MENU] to menu.
  2. [Up/Down] to "SMS", [MENU].
  3. [Up/Down] to "Sent SMS", [MENU].
  4. [Up/Down] to desired SMS, [MENU]. (If from Email, shows subject line).

Send Already Sent SMS: When reading, options: Re-send, Forward, Edit, Delete.

Re-send:

  1. [MENU] again.
  2. [Up/Down] to "Re-send", [MENU].
  3. LCD shows "SMS :< User/call group alias or ID>", confirms sending.
  4. If successful, beep, screen shows "sent". If failed, high-pitched tone, screen shows "failed".

If failed, returns to re-send screen. [MENU] to re-send. [Up/Down] returns to SMS by changing volume/pressing other button.

Exits re-send screen if individual/group call, SMS/telemetry, emergency call/alarm, or call alert received. Returns to re-send mode if [MENU] pressed to respond to individual call (unless not received) or group call finished. [Up/Down] enters transfer/edit/delete screen.

  • Transfer: Sends selected SMS to other group/user.
  • Edit: Edits SMS before sending.
  • Delete: Deletes selected SMS.

CAUTION:

If you exit SMS sent screen when sending, radio updates "Sent item" file without reminder/beep. If mode changes or power off before update, radio won't handle sending, shows "sent failed". Radio handles 5 SMS simultaneously. Cannot send new SMS if 5 failed.

Delete Already Sent SMS:

  1. [MENU] to menu.
  2. [Up/Down] to "SMS", [MENU].
  3. [Up/Down] to "Sent SMS", [MENU].
  4. [Up/Down] to "Delete ALL", [MENU].
  5. [Up/Down] to "YES", [MENU].
  6. Screen shows "SMS has been deleted".
  7. Returns to inbox.

Delete All SMS in Inbox:

  1. [MENU] to menu.
  2. [Up/Down] to "SMS", [MENU].
  3. [Up/Down] to "Inbox", [MENU].
  4. [Up/Down] to "Delete all", [MENU].
  5. [Up/Down] to "YES", [MENU].
  6. Screen shows "inbox was emptied".

If "Inbox" selected and empty, screen shows "empty". Low tone beep if key tone on.

Receive SMS: Screen displays sender's alias/ID and text message icon. Options: Read, Read later, Delete.

CAUTION:

If [PTT] pressed while prompt screen displayed, radio exits SMS prompt and establishes individual/group call.

Check SMS:

  1. [Up/Down] to "Read", [MENU].
  2. If from Email, shows subject line.
  3. [MENU] to return to inbox. Or [MENU] to reply/transfer/delete.
  4. [Up/Down] to "Read Later" or delete.
  5. "Read Later": returns to screen before receive.
  6. "Delete": deletes received SMS.

Manage Received SMS: Inbox stores up to 50 messages. Options: Reply, Transfer, Delete, Delete All. Stores messages by most recently received.

Read SMS in Inbox:

  1. [MENU] to menu.
  2. [Up/Down] to "SMS", [MENU].
  3. [Up/Down] to "Inbox", [MENU].
  4. [Up/Down] to read SMS. (If from Email, shows subject line).
  5. [MENU] to current SMS, then [MENU] again to reply/delete/forward.

Icons: [Envelope] indicates unread, [Open Envelope] indicates read.

Reply SMS in Inbox:

  1. [MENU] to menu.
  2. [Up/Down] to "SMS", [MENU].
  3. [Up/Down] to "Inbox", [MENU].
  4. [Up/Down] to desired SMS, [MENU]. (If from Email, shows subject line).
  5. [MENU] again to sub-menu.
  6. [Up/Down] to "reply", [MENU].
  7. [Up/Down] to "Write SMS", [MENU]. Blinking cursor, edit. Or [Up/Down] to prefabricated SMS, [MENU]. Edit if needed.
  8. After edit, [MENU].
  9. LCD shows "SMS :< User/Call group alias or ID>", confirms sending.
  10. If successful, beep, screen shows "sent". If failed, high-pitched tone, screen shows "failed". Returns to re-send screen.

Delete SMS in Inbox:

  1. [MENU] to menu.
  2. [Up/Down] to "SMS", [MENU].
  3. [Up/Down] to "Inbox", [MENU].
  4. [Up/Down] to desired SMS, [MENU]. (If from Email, shows subject line).
  5. [MENU] again to sub-menu.
  6. [Up/Down] to "delete", [MENU].
  7. [Up/Down] to "YES", [MENU].
  8. Screen shows "SMS has been deleted".
  9. Returns to inbox.

Encryption

Prevents unauthorized eavesdropping. Transmitted signal and user ID parts are not encrypted. Radio must be encrypted on channel to send encrypted transmissions.

Basic Encryption: Radio assigned one encryption type. To decrypt, receiving radio must be pre-programmed with same "Encryption Key". If different keys/values/IDs, chaotic transmission sound.

Press Pre-programmed Encryption button to turn on/off.

ANI ID Code Display: Under Analog mode, set PTT ID by program software (Channel information -> Analog data -> Display PTT ID). LCD displays ANI ID code when DTMF signal received.

Confidentiality

Activate or remote kill any radio (e.g., stolen radio). Limited to active radios with these functions.

Activate/Remote Kill Host Computer Settings (Program Software):

  1. Edit -> DTMF -> Signal -> Decode -> Response style, choose activation/remote kill.
  2. DTMF number -> input corresponding number.
  3. In channel information, choose corresponding receive signal system (same as step 2), tick decode X (same number as step 2).
  4. When corresponding DTMF number received, activation/remote kill achieved.

Radio Remote Kill (Menu):

  1. [MENU] to menu.
  2. [Up/Down] to contact list, [MENU] to select (alphabetical).
  3. [Up/Down] to desired alias/ID, [MENU]. Or [Up/Down] to manual dialing, [MENU] twice, input alias/ID, [MENU].
  4. [Up/Down] to radio remote kill, [MENU].
  5. LCD shows "radio remote kill: <User alias or ID>", LED flashes red.
  6. Wait for confirmation.
  7. If successful, beep, screen shows "successfully remote killed". If failed, beep, screen shows "failed".

During remote kill, do not press [BACK] to receive confirmation.

Radio Activation (Menu):

  1. [MENU] to menu.
  2. [Up/Down] to contact list, [MENU] to select (alphabetical).
  3. [Up/Down] to desired alias/ID, [MENU]. Or [Up/Down] to manual dialing, [MENU] twice, input alias/ID, [MENU].
  4. [Up/Down] to radio activation, [MENU].
  5. LCD shows "radio activated: <User alias or ID>", LED flashes red.
  6. Wait for confirmation.
  7. If successful, beep, screen shows "successfully activated". If failed, beep, screen shows "failed".

During radio activation, do not press [BACK] to receive confirmation.

Scan List

Receives communication activity from other channels/groups. Supports up to 250 scan lists (max 32 members), mixing analog/digital channels. Add/delete/prioritize channels by editing.

Read Scan List:

  1. Use channel knob to choose pre-programmed scan list.
  2. [MENU] to menu.
  3. [Up/Down] to scan, [MENU].
  4. [Up/Down] to read list, [MENU].
  5. [Up/Down] to read every member.

If priority set, icon displayed next to alias (1 for priority 1, 2 for priority 2). No icon if priority set as "N". Multiple priority 1/2 not allowed in one list. Cannot delete first channel in list.

Add Scan Channel:

  1. [MENU] to menu.
  2. [Up/Down] to scan, [MENU].
  3. [Up/Down] to add channel, [MENU].
  4. [Up/Down] to desired channel, [MENU].
  5. Screen shows "Success to add channel", returns to upper menu.

Scan Instruction and Method: Radio checks for voice activity on current channel by cycling pre-programmed scan list. Red LED flashes, scan icon appears. During duplex scan, if on digital channel and locks analog, auto-switches to analog for call duration.

Two ways to scan:

  • Manual Scan: Start via pre-programmed scan on/off button or menu. Detects all pre-set channels/groups.
  • Automatically Scan: If activated channel/group chosen, radio scans from it.

Start and Stop Scan: Press pre-programmed scan on/off button or enter scan menu.

  1. Use channel knob to choose pre-programmed scan list.
  2. [MENU] to menu.
  3. [Up/Down] to scan, [MENU].
  4. If stopped, screen shows "open". If activated, screen shows "close".
  5. [MENU] to choose.

When activated, red LED flashes, scan icon appears. When stopped, LED off, no scan icon.

Scan Reply: During scan, radio stops at channel/group with activity ("Scan suspend time").

  1. Hold radio upright (1-2 inches from mouth). If "Free channel beep" enabled, short beep indicates channel free.
  2. Press [PTT] during suspend time (LED red).
  3. Release [PTT] to receive.
  4. If no response during suspend time, radio continues scanning.

Menu Settings

Customize radio settings for optimal performance. Enter "Setting -> Radio setting" to configure.

Radio Settings Options
Setting OptionsOptions and RangeDescription of Operation
OfflineON/OFFON: works only when "Allow offline" ticked. OFF: turns off.
All tonesOff/OnTurns off all tones (excluding emergency alarm) when Off selected.
Tone/Prompt tone (Call permission)Off/Digital/AnalogPressing PTT transmits signal and sounds tone. Off: no tone. Digital: tone for digital. Analog: tone for analog.
Tone/Prompt tone (Touch-tone)Off/OnNo prompt tone when Off selected.
Transmission powerLow/HighLow/High power transmission.
BacklightNormally on/5~15 secNormally on: always on (power saving disabled). 5~15 sec: auto turn off when time up.
Squelch LevelNormally/StrictlyFilters useless calls/background noise.
Boot interfacePicture/Preset charactersPicture: display customer-provided. Preset: two lines, editable by host.
Keypad lock and unlockManual/5/10/15 secManual: press & hold # to lock/unlock. Auto: locks automatically after set time.
Language selectionEnglish/ChineseEnglish: menu, call tips, logs, etc. Chinese: Simplified Chinese.
LED IndicatorOFF/ONOFF: indicator (transmission, receiving, boot) doesn't work. ON: default.
Voice controlOFF/ONOFF: VOX turned off. ON: no PTT needed.
Power on passwordEnter passwordInput correct password to enter setup menu (configurable by host).
O'clockTime/Date/Time zoneSet Hour/Minutes/Seconds, Year/Month/Date, choose time zone.
Mode selectionChannel display/Frequency displayChannel mode displayed by name/frequency.
Single call match(Not detailed in source)(Not detailed in source)
Group call match(Not detailed in source)(Not detailed in source)

Radio Information Query

Check radio number (owner name, serial number) and version (firmware, CPS, programming time).

[BACK] returns to previous screen.

Check Radio ID:

  1. [MENU] to menu.
  2. [Up/Down] to set, [MENU].
  3. [Up/Down] to radio setting, [MENU].
  4. [Up/Down] to radio number, [MENU].
  5. Screen shows radio ID and name.

Check Radio Version:

  1. [MENU] to menu.
  2. [Up/Down] to set, [MENU].
  3. [Up/Down] to radio information, [MENU].
  4. [Up/Down] to radio version, [MENU].
  5. Screen shows current firmware version, CPS version.

Radio Configuration

Mainly to edit channel content. Path: Settings -> radio configuration menu, select items to configure.

Receiving Frequency:

  1. [MENU] to menu.
  2. [Up/Down] to set, [MENU].
  3. [Up/Down] to radio configuration, [MENU].
  4. Key in correct password (software settings), [MENU].
  5. [Up/Down] to receiving frequency, [MENU].
  6. Screen shows current channel receiving frequency, [MENU].
  7. Key in number, [Up] to delete last, [BACK] to previous menu.
  8. After changes, [MENU]. Screen shows saved.

Note: Frequency changes are limited by software range. Final result will be min/max value if outside range.

Transmitting Frequency: (Same steps as Receiving Frequency, but select "transmitting frequency").

Channel Name:

  1. [MENU] to menu.
  2. [Up/Down] to set, [MENU].
  3. [Up/Down] to radio configuration, [MENU].
  4. Key in correct password (software settings), [MENU].
  5. [Up/Down] to channel name, [MENU].
  6. Screen shows current channel name, [#] to switch input method (same as SMS editing).
  7. After changes, [MENU]. Screen shows saved.

Transmit Time-Out Timer (TOT): Prevents long channel occupation. If continuous transmit exceeds set time, radio stops and warns. Release [PTT] to stop warning. Press [PTT] again after period (dealer set) to transmit.

  1. [MENU] to menu.
  2. [Up/Down] to set, [MENU].
  3. [Up/Down] to radio configuration, [MENU].
  4. Key in correct password (software settings), [MENU].
  5. [Up/Down] to time-out timer, [MENU].
  6. Screen shows infinity, 15S, 30S...555S options (15S increments). [Up/Down] to option, [MENU]. If infinity, screen shows "turn off". If others, shows "xxS".

CAUTION:

Invalid in emergency alarm mode.

CTCSS: Set only under simulated channel. Includes CTCSS encode/decode.

CTCSS Encode:

  1. [MENU] to menu.
  2. [Up/Down] to set, [MENU].
  3. [Up/Down] to radio configuration, [MENU].
  4. Key in correct password (software settings), [MENU].
  5. [Up/Down] to CTCSS, [MENU].
  6. [Up/Down] to CTCSS encode, [MENU].
  7. Screen shows "turn off" group of CTCSS encode number. [Up/Down] to close, [Up/Down] to select (no value, shows "closed"). Or [Up/Down] to value, [MENU] (shows "XX").

CTCSS Decode: (Same steps as CTCSS Encode, but select "CTCSS decode").

Add Channel (Menu):

  1. [MENU] to menu.
  2. [Up/Down] to SETTING, [MENU].
  3. [Up/Down] to CONFIGURATION, [MENU].
  4. Input password, [MENU].
  5. [Up/Down] to Add Channel, [MENU].
  6. [Up/Down] to select channel, [MENU] to enter and add parameters.

Color Code: System for communication. Terminals must have same color code (0-15). Set only in digital model. Marks system.

Color Code (Menu):

  1. [MENU] to menu.
  2. [Up/Down] to SETTING, [MENU].
  3. [Up/Down] to CONFIGURATION, [MENU].
  4. Input password, [MENU].
  5. [Up/Down] to Color code, [MENU].
  6. [Up/Down] to select color code, [MENU]. Selected code displayed.

Relay Station Time Slot: Slot for voice/data transmission, modifiable only in digital channels.

Relay Station Time Slot (Menu):

  1. [MENU] to menu.
  2. [Up/Down] to SETTING, [MENU].
  3. [Up/Down] to CONFIGURATION, [MENU].
  4. Input password, [MENU].
  5. [Up/Down] to Relay Station Time Slot, [MENU].
  6. [Up/Down] to select slot, [MENU]. Selected slot displayed.

Digital channel can be configured for dual capacity direct mode (parallel direct mode transmission of two radios on 12.5KHz). Radios in same group must use same time slot; slot 1 won't interfere with slot 2.

VOX: Higher VOX level = lower sensitivity, louder sound to trigger. Modifiable by writing-frequency software (level 1 highest, 10 lowest).

VOX (Menu):

  1. [MENU] to menu.
  2. [Up/Down] to SETTING, [MENU].
  3. [Up/Down] to CONFIGURATION, [MENU].
  4. Input password, [MENU].
  5. [Up/Down] to Color code, [MENU].
  6. [Up/Down] to select color code, [MENU]. Selected code displayed.

CAUTION:

Adjust voice gain correctly to environment/speaking volume to avoid accidental triggering (too high) or difficulty triggering (too low).

Transmitting Contacts: Modifiable only in digital channels.

Transmitting Contacts (Menu):

  1. [MENU] to menu.
  2. [Up/Down] to SETTING, [MENU].
  3. [Up/Down] to CONFIGURATION, [MENU].
  4. Input password, [MENU].
  5. [Up/Down] to transmitting contactor, [MENU].
  6. [Up/Down] to select contactor, [MENU]. Selected contactor displayed.

Group Call List: Modifiable only in digital channels.

Group Call List (Menu):

  1. [MENU] to menu.
  2. [Up/Down] to SETTING, [MENU].
  3. [Up/Down] to CONFIGURATION, [MENU].
  4. Input password, [MENU].
  5. [Up/Down] to group call list, [MENU].
  6. [Up/Down] to select group call list (delete/add member). [Up/Down] to add new group call.

5. Maintenance

General Maintenance

To maintain performance and extend service life:

  • Do not store in corrosive electronic circuit material environments.
  • Do not directly lift by antenna or external microphone.
  • Cover appendage interface when not in use.

Cleaning

  • Use a clean, dry cloth or brush to wipe the walkie-talkie surface and charging pole regularly.
  • Wipe dirt/dust with a lint-free cloth to prevent poor contact.
  • For long-term use, buttons, knobs, and chassis may get dirty. Use neutral detergent (no strong corrosives) and a wet cloth. Ensure radio is completely dry before use.
  • When not in use, attach the cover on the socket.

CAUTION:

Turn off the radio and remove the battery before cleaning.

6. Troubleshooting

If you encounter issues, refer to the table below. If problems persist, contact your local distributor for technical support.

Troubleshooting Guide
ProblemReasonSolution
Radio doesn't startBattery not installed correctlyRemove and re-install battery
Battery runs outCharge or change battery
Battery poor contact (damaged/dirty)Clean contact. Contact distributor for repair.
Sound small/intermittent, or noisy on receptionBattery voltage lowCharge or change battery
Voice too smallTurn up sound
Antenna looseTurn off radio, re-install antenna
Speaker damaged/dirtyClean speaker. Contact distributor for repair.
Cannot talk with other members in groupFrequency differentReset to same frequency
Different digital/analog channelsCorrect to same channel
Too far awayGet closer
Single/group call not working in digital channelToo far awayGet closer
Different frequency/channel/color code/time slotSet to same frequency/channel/color code/time slot
Other sound in channel (not from members)Interference from same frequencyChange frequency, or correct squelch
Signal not set yetSet signal for all radios
Loud noiseToo far awayGet closer
Poor location (blocked, basement)Move to open environment, restart radio
Interference (environment/electromagnetic)Avoid interfering device

7. Specifications

The following are the main technological specifications for the Baofeng DM-1702:

Baofeng DM-1702 Basic Parameters Diagram

Diagram Description: This image shows the front view of the Baofeng DM-1702 with dimensions (13.3cm height, 6.2cm width, 3.6cm depth) and lists key parameters.

General Specifications
ParameterValue
Model NameDM-1702
Call Distance2-10 KM
Power5W
Battery Capacity2200mAh
Frequency RangeVHF/UHF 137-174MHz / 400-470MHz
Channels1024
Product Size133*62*36mm
Weight250g
Accessories IncludedHost, antenna, battery, back clip, charger, manual, bracelet*
Main Technological Specifications
FeatureSpecification
Frequency RangeVHF:136-174MHz / UHF:400-480MHz (Dual band)
Memory ChannelUp to 3000
Frequency Stability±1.0ppm
Operating Temperature-30°C ~ +60°C
Operating VoltageDC 7.4V
Dimensions (excluding antenna)133*62*36mm
Weight(Not including antenna)
Transmission
Output PowerHigh:5W, Low:1W
Output ConsumptionAnalog ≤1.6A, Digital ≤0.9A
Consumption (Standby)<0.18A
FM Modulation16KCF3E@25KHz, 141KCF3E@20KHz, 11KCF3E@12.5KHz
4FSK Digital Modulation12.5KHz for data: 7K60FXD, 12.5KHz for data and voice: 7K60FXE
Modulation Distortion<5%
Signal-to-Noise (Wide/Narrow)≥45dB@25KHz, ≥40dB@12.5KHz
Adjacent Channel Power≤-65dB, ≤-60dB
Audio Response+1~3dB
Antenna Port Spurious9KHz-1GHz: ≤-36dBm, 1GHz-12.75GHz: ≤-30dBm
Digital ProtocolETSI-TS102 361-1,-2,-3
Vocoder TypeAMBE+2™
Reception
Analog Receive Sensitivity-122dBm (12dB SINAD)
Digital Receive Sensitivity-120dBm (BER≤5%)
Audio Power1W
Audio Distortion<10%
Audio Response+1~-3dB
Signal Imitation≥70dB
Intermediation (Wide/Narrow)≥62dB/≥58dB
Adjacent Channel Selectivity≥65dB/≥60dB
Receive Current≤380mA
PM Noise≥45dB@25KHz/≥40dB@12.5KHz

CAUTION:

All specifications may be modified without prior notice or liability.

8. User Tips

  • Unboxing: Carefully inspect the package upon arrival. Ensure all listed accessories (host, antenna, battery, back clip, charger, manual, bracelet) are present and undamaged. Report any discrepancies immediately.
  • Software and Drivers: While the manual covers basic operation, advanced programming often requires specific software and drivers. Check the official Baofeng website or your dealer for the correct tools for the DM-1702 model. Community-developed software like 'openGD77' might exist for some DMR radios, but compatibility with the DM-1702 is not guaranteed and using unofficial software may void your warranty or cause device malfunction. Proceed with caution and at your own risk.
  • Language Support: The device supports English and Chinese. Ensure you select your preferred language in the settings for easier navigation.
  • Manual Reference: This manual incorporates content from the official PDF. For a complete, original document, refer to the PDF provided by the seller.

9. Warranty and Support

For warranty information, technical support, and service inquiries, please contact your authorized Baofeng dealer or visit the official Baofeng website. Keep your purchase receipt as proof of purchase.

Disclaimer: The accuracy and completeness of this manual's contents are diligently sought. However, we do not bear responsibility for possible errors or omissions. Due to continuous technological development, we reserve the right to change the design and specifications of the product without prior notice. No part of this handbook may be reproduced, modified, translated, or disseminated without written authorization.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.