BAOFENG UV-17pro Max

Contents

Baofeng UV-17pro Max Air Band Walkie Talkie User Manual

Model: UV-17pro Max | Brand: BAOFENG

1. Getting Started

1.1 Regulations and Safety Warnings

Thank you for purchasing this product. This dual band/dual display/dual watch radio is designed to deliver secure, instant, and reliable communications at peak efficiency. Please read this manual carefully before use to ensure maximum performance from your radio.

General Warnings

WARNING! European Users should note that operation of this unit in Transmit mode requires a valid Amateur Radio License from their respective Countries Amateur Radio Licensing Authority for the Frequencies and Transmitter Power levels that this Radio transmits on. Failure to comply may be unlawful and liable for prosecution. Refer to the "EU" specification guide 2014/53/EU.

ATTENTION! When programming the radio, always start by reading the factory software data. Then, rewrite this data with your desired frequency settings. Otherwise, errors may occur. Use the programming cable with a PC to program authorized frequencies, bandwidth, power, etc. Your programming must comply with your FCC (or EU other country) license certification.

ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the radio. This guide contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.

PMR446, FRS, GMRS, MURS: You may be tempted to use PMR446 (in Europe) or FRS, GMRS, MURS (in the USA) frequencies. Do note however that there are restrictions on these bands that make this transceiver illegal for use.

EU Regulatory Conformance

As certified by the qualified laboratory, the product complies with the essential requirements and other relevant provisions of Directive 1999/5/EC (2014/53/EU). All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU, 2012/19/EU). This information is applicable to EU countries only.

FCC Part 15 / IC Compliance

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

FCC RF Exposure: It is up to the user to properly operate this radio transmitter to ensure safe operation. Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Contact your local dealer for a replacement antenna.

Hand-Held Operation (Held-to-Face): This device was evaluated for typical hand-held (held-to-face) operations with a 1-inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face to comply with FCC RF exposure requirements.

Body-Worn Operation: This device was evaluated for body-worn operations with the supplied belt-clip accessory. All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines. Third-party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines.

Precautions for Portable Terminals

Operating Prohibitions:

  1. Do not operate the product in a location containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  2. Do not operate the product near or in any blasting area.
  3. Do not operate the product near any medical or electronic equipment vulnerable to RF signals.
  4. Do not hold the product while driving.
  5. Do not operate the product in any area where wireless communication equipment is completely prohibited.

Important Tips:

  1. Do not use any unauthorized or damaged accessory.
  2. Keep the product at least 2.5 centimeters away from your body during transmission.
  3. Do not keep the product receiving at high volume for a long time.
  4. For vehicles with an airbag, do not place the product in the area over the airbag or in the airbag deployment area.
  5. Keep the product and its accessories out of reach of children and pets.
  6. Operate the product within the specified temperature range.
  7. Continuous transmission for a long time may lead to heat accumulation. Keep it at a proper location for cooling.
  8. Handle the product with care.
  9. Do not disassemble, modify, or repair the product and its accessories without authorization.

Precautions for Batteries

Charging Prohibitions:

  1. Do not charge or replace your battery in a location containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
  2. Do not charge a wet battery. Dry it with a soft, clean cloth prior to charging.
  3. Do not charge a battery suffering deformation, leakage, or overheat.
  4. Do not charge your battery with an unauthorized charger.
  5. Do not charge your battery in a location where strong radiation is present.
  6. Overcharge is prohibited as it may shorten battery life.

1.2 Main Features

  • Frequency range: FM radio 65-108 MHz; AM aviation frequency band: 108-136MHz (RX)
  • VHF1: 136-174MHz (RX&TX); VHF2: 220-260MHz (RX&TX)
  • UHF1: 400-520MHz (RX&TX); UHF2: 350-390MHz (RX)
  • One-touch search frequency, easy pairing and grouping (copying channel configuration parameters)
  • Frequency step, selectable between 2.5K | 5.0K | 6.25K | 10.0K | 12.5K | 20.0K | 25.0K | 50.0K
  • Frequency hopping and scramble functions for call privacy
  • 1.77" TFT large screen, full keyboard, fully open menu operation
  • Channel scan, frequency scan, and three scan and recovery methods: TO, CO, and SE
  • Up to 999 memory channels.
  • Power-on password management function
  • DTMF encoder and DTMF manual dial
  • VOX (voice activated transmit).
  • Alarm function.
  • High or low power selectable.
  • Programmable repeater offset.
  • Transmission time-out timer.
  • LED flashlight.
  • End of transmission tone, aka "Roger Beep"
  • Broadcast FM radio receiver 65-108 MHz
  • Dual watch / Dual reception/ Dual-band handheld transceiver
  • High Capacity Lithium-Ion battery.
  • Stopwatch function
  • Display illumination programmable via keypad.
  • Function beep on the keyboard.
  • Battery save function.
  • Busy channel lock out.
  • Ten (10) levels of Squelch adjustment.
  • Two (2) pins for Kenwood accessory port
  • Support NOAA weather reception function in the United States and Canada

1.3 Content of the Packaging

The package should contain the following items. If any item is missing, please verify with your dealer.

  • 1 Radio
  • 1 Fast Type-C charger
  • 1 Antenna
  • 1 Li-Ion battery pack
  • 1 Belt clip
Baofeng UV-17 Pro Max accessories and specifications
Figure 1: Included accessories and key parameters. Includes the radio unit, antenna, battery, manual, belt clip, lanyard, and Type-C charging cable.
Baofeng BF-17 P.M Series User Manual Cover
Figure 2: Cover of the BF-17 P.M Series User Manual.

2. Setup

2.1 Charging the Battery

The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/discharging the battery two or three times before the operating capacity reaches its best performance. The battery pack life may be depleted when its operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack.

Charger Supplied

Please use the specified charger provided by our company. Other models may cause explosion and personal injury. After installing the battery pack, if the radio displays low battery with a voice prompt, please charge the battery.

Use Caution with the Li-ion Battery

  • Do not short the battery terminals or throw the battery into a fire. Never attempt to remove the casing from the battery pack.
  • The ambient temperature should be between 5°C-40°C (40°F-105°F) while charging the battery. Charging outside this range may not fully charge the battery.
  • Turn off the radio before inserting it into the charger. It may otherwise interfere with correct charging.
  • To avoid interfering with the charging cycle, do not cut off the power or remove the battery during charging until the green light is on.
  • Do not recharge the battery pack if it is fully charged. This may shorten the life of the battery pack or damage the battery.
  • Do not charge the battery or the radio if it is damp. Dry it before charging to avoid damage.
  • When keys, ornamental chains, or other electric metals contact the battery terminal, the battery may be damaged or injure a human. If the battery terminals are short-circuited, it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.

How to Charge

  1. Plug the AC adaptor into the AC outlet, then plug the cable of the AC adaptor into the DC jack on the back of the charger. The indicator light blinks orange and is then ready to charge a battery.
  2. Plug the battery or the radio into the charger. Ensure the battery terminals are in good contact with charging terminals. The indicator light turns red, indicating charging has begun.
  3. It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, charging is completed. Remove the battery or the radio unit with its battery from the socket.

Note: When charging a radio (with battery), the indicating lamp will not turn green to show fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is powered on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.

LED Indicator Status

STATUS LED
No Battery Green and red alternately flashing
Charge Normally Red
Fully Charged Green
Trouble Red blinks fast for a long time

NOTE: Trouble means battery too warm, battery short-circuited, or charger short-circuited.

Using the Type-C USB Charger

The Type-C USB charger provides a convenient way to charge your Li-ion battery pack.

  1. Make sure your radio is turned OFF.
  2. Plug the Type-C USB cable into the Type-C USB charging port on your battery. Connect the other end of the micro-USB charger to a wall power outlet.
  3. An empty battery will be fully charged in 4 hours.
  4. The battery meter on the LCD will move to indicate the battery is charging.

Note: It is recommended to power OFF your radio while charging. However, if power is turned on while charging, you may not be able to transmit a message if the battery is completely empty. Allow time for the battery to charge to 1 bar before attempting to transmit a message. For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger.

2.2 Installation of Accessories

Before the radio is ready for use, you need to attach the battery pack and charge the battery.

Installing / Removing the Antenna

  • Installing the Antenna: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
  • Removing the Antenna: Turn the antenna counter-clockwise to remove it.

Installing the Belt Clip

  • At the back of the radio, there are two parallel screws mounted above the battery. Remove these and thread them through the holes on the belt clip as you screw them back into the radio body.
  • Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip.
Back of Baofeng UV-17 Pro Max with belt clip and Type-C port
Figure 3: Rear view of the radio showing the belt clip and Type-C charging port.

Installing the Battery Pack

Before attaching or removing the battery, make sure your radio is turned off by turning the power/volume knob all the way counter-clockwise.

  1. Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
  2. Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place.

Removing the Battery Pack: To remove the battery, press the battery release above the battery pack, as you slide the battery downward.

Installing the Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

2.3 Radio Overview

Baofeng UV-17 Pro Max with display showing FM/AM radio reception
Figure 4: Front view of the Baofeng UV-17 Pro Max, highlighting the display and keypad.
Baofeng UV-17 Pro Max with frequency bands and features
Figure 5: Overview of the Baofeng UV-17 Pro Max, detailing its frequency bands and features like Wireless Copy Frequency, Type-C Charger, AM/FM.

Buttons and Controls

  1. Antenna
  2. Flashlight/ Emergency Alert key
  3. PTT key
  4. FM broadcast/Monitor key
  5. MENU Key
  6. Numeric keypad
  7. Power/Volume knob
  8. Color LCD
  9. Accessory jack
  10. MIC Input
  11. EXIT Key
  12. Up/Down navigation keys
  13. Battery pack
  14. Type-C charging port
  15. Battery tightening screw
  16. Type-C charging indicator
  17. LED flashlight
  18. TX/RX Status LED

LCD Display Icons

Icon Description
RSSISquelch Open/Close Indicator
H/LTransmit power level indicator (High/Low)
♪DTMF side tone from radio speaker (DT-ST, ANI-ST, DT+ANI)
(D)DCS enabled
(C)CTCSS enabled
+Access to repeaters in VFO/Frequency Mode (TX shifted higher)
-Access to repeaters in VFO/Frequency Mode (TX shifted lower)
DDual watch enabled
.Keypad lock enabled
VOXVOX enabled
Confidential calling feature activated
NNarrowband enabled
Battery level indicator
RReverse function enabled
►Indicates active band or channel
SCRVoice scramble function activated

Battery Level Indicator

When the battery level indicator reads [battery icon] the battery is depleted. At this point, the radio will start beeping periodically and flash the backlight of the display. If voice prompts are enabled, a "Low Voltage" announcement will be heard, indicating that you need to change your battery or put your radio in the charger.

Status Indications

The status LED has a very simple and traditional design:

LED Indicator Radio Status
Constant RedTransmitting.
Constant GreenReceiving.

3. Operating Instructions

3.1 Basic Operations

Main Keypad Controls

  • Side key 1 (Flashlight and Alarm): Press [SK1] momentarily to turn on the LED flashlight. Another momentary press flashes the LED. Another momentary press turns the flashlight off. Press and hold [SK1] to activate the alarm function. Press [SK1] (a short press) again to turn it off.
  • Side key 2 (Broadcast FM and Monitor): Press [SK2] momentarily to start the broadcast FM receiver. Another momentary press turns the broadcast FM receiver off. If a signal is received on the active frequency or channel while listening to broadcast FM, the receiver will open squelch to that frequency (as if scanning) and remain there until the signal goes away; it will then switch back to broadcast FM. Press and hold [SK2] to monitor the signal, opening the squelch to listen to the unfiltered signal.
  • MENU Key: Used for activating the MENU, choosing each MENU selection, and confirming parameters. In standby mode, press and hold the MENU key to switch between frequency (VFO) mode and channel (MR) mode.
  • Up/Down Keys: Press for more than 2 seconds to move channels and frequencies rapidly upwards/downwards. In SCAN mode, these controls move scanning upwards/downwards.
  • EXIT Key: Press to exit the Menu and functions. A/B (appears on the display): press to select the desired frequency (VHF or UHF) in the main or secondary display. Press and hold the EXIT key to activate the one-touch search function.
  • Numeric keypad: Input information or selections. In TX mode, press number keys to send corresponding DTMF code.
  • Star * Key: A short momentary press enables the reverse function. Press for more than 2 seconds to lock/unlock the keypad.
  • Pound # Key: Press to activate the DTMF dial function. Press and hold to activate channel scan or frequency scan. In FM radio mode, press to automatically search for broadcast programs.
  • 0 key: Press and hold [0sQL] key to activate the NOAA weather forecast reception function.

Power On/Off the Radio

  • Turning the unit on: Rotate the Volume/Power knob clockwise until you hear a "click". An audible double beep and display message/flash should occur. If Voice prompt is enabled, it will announce "frequency mode" or "channel mode".
  • Turning the unit off: Turn the Volume/Power knob counter-clockwise all the way until you hear a "click". The unit is now off.

Adjusting the Volume

To turn up the volume, turn the Volume/Power knob clockwise. To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as you may inadvertently turn your radio off. Use the monitor function (enabled from the [FM broadcast/Monitor] key below the PTT) to adjust volume more easily by adjusting it to the un-squelched static.

Main Band/Sub Band Select

In standby mode, press the [A/B] key to switch between A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel. To save frequencies to channel memory, you must be on the A display.

VFO/Channel Switch

Press and hold the [VFO/MR] key to switch between VFO and channel display.

  • In channel mode (MR), the channel number will be displayed on the right.
  • In frequency mode (VFO), 'VFO' will be displayed on the right.

Frequency (VFO) Mode

In Frequency (VFO) mode, you can navigate up and down the band using the UP or DOWN keys. Each press increments or decrements your frequency according to the frequency step you've set. You can also input frequencies directly on your numeric keypad with kilohertz accuracy.

WARNING! Just because you can program a channel does not mean you're automatically authorized to use that frequency. Transmitting on unauthorized frequencies is illegal and a serious offense. However, listening is legal. Contact your local regulatory body for information on applicable laws.

Channel (MR) Mode and Channel Selection

For everyday use, Channel (MR) mode is more practical than Frequency (VFO) mode. In Channel (MR) mode, you can navigate up and down the channel using the UP or DOWN keys or the encoder. You can also input channel numbers directly via the keyboard (e.g., [0][1][2] for channel 12). If voice prompt is enabled, the channel will be broadcast by voice.

Making a Call

Note: Press the [A/B] key to switch the main channel if two channels are shown. In standby, press and hold the [VFO/MR] key to switch between VFO and MR mode.

  • Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with a normal tone. The red LED will be on.
  • Frequency mode call: Press and hold the [VFO/MR] key to switch to frequency mode, input the working frequency, and press and hold the [PTT] key to transmit. The red LED will be on.
  • Receive a call: When you release the [PTT] key, you can answer without action. The green LED will be on when receiving a call.

Note: For best reception volume, keep the distance between the microphone and your mouth between 2.5 cm and 5 cm during transmission.

Using the Flashlight

Press the [Flashlight] key once for continuous light, again for strobe, and a third time to turn it off. Your radio operates normally when the emergency strobe is activated.

Emergency Alert

The Emergency Alert feature signals members in your group for help. Press and hold the [Flashlight] key for 3 seconds to activate. The radio will emit a loud siren and the flashlight will flash. Press the [Flashlight] key again to exit. WARNING: Use this feature only in an actual emergency.

FM Radio (FM)

The frequency range for FM radio is 65-108MHz. When listening to broadcast FM, the [FM] key switches between 65-75 MHz and 76-108 MHz bands.

  1. In frequency or channel mode, press [SK2] to turn on the radio.
  2. Select the desired radio frequency with the UP or DOWN keys or input the frequency. Alternatively, press [#] to automatically search for a radio station.
  3. Press [SK2] to exit FM radio.

Note: While listening to the radio, if an A/B receiving signal is detected, it will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears, the radio will switch back to FM radio mode.

Monitor

In standby, press and hold the [SK2] key to enter Monitor. This function allows monitoring weak signals even if the matched carrier or signaling is too weak. Stop pressing [SK2] to turn off speakers and return to standby. If no signal, it will emit noise when [SK2] is pressed.

3.2 Advanced Features

Keypad Lock

The keypad lock disables all keys except the three side keys. To enable or disable, press and hold the [*] key for about two seconds. You can also set the radio to automatically lock the keypad after ten seconds from the menu.

Frequency Reversal

A short momentary press of the [*] key enables the reverse function. If you want to listen to the repeater's input frequency, press [*] momentarily to reverse your transmit and receive frequencies. After activating, "R" will be displayed on the first line of the screen.

TX Repeaters Tone

Press [PTT] + [CALL] key to send a 1750Hz repeaters tone. This is useful for communications through repeaters. If the keypad lock is enabled, you can still send the 1750Hz tone without unlocking the radio.

Step-by-step guide to decode walkie talkie frequency
Figure 6: Instructions for decoding another walkie talkie's frequency.
2 seconds copy frequency feature
Figure 7: Demonstrates the quick 2-second frequency copy feature.
  1. The radio acts as a receiver. Press and hold the [EXIT] key, and the screen will display "SEARCH SEARCH...".
  2. If the transmitter continues to transmit and the unit receives an effective frequency (strongest and stable signal), the received frequency will be displayed. If a CTCSS or DCS is present, it will be displayed; otherwise, "NONE" is shown.
  3. Press the [MENU] key to save the Search frequency and CTCSS or DCS to the channel.

Note: During frequency Search, press the [#] key on the radio to switch between UHF or VHF bands.

Green walkie talkie display showing search
Figure 8: Radio display during a frequency search, showing "SEARCH UHF SEARCH...".

Weather Radio/Scan Weather Channel (NOAA)

Your radio has a NOAA Weather Radio function to receive weather reports from designated NOAA stations. It also has a NOAA Weather Scan function to scan all 10 channels of the NOAA Weather Radio.

  1. To turn NOAA Weather Scan on, press and hold the [0] key for 3 seconds. The [cloud icon] appears, and the radio goes to Weather band mode.
  2. Press and hold the [#] key for 3 seconds to start automatic scanning of all 10 channels and stop on active channels. Pressing and holding the [#] key for 3 seconds during a NOAA weather scan will stop the scan.
  3. After stopping NOAA weather scan, you can manually select the weather channel by pressing the UP or DOWN key.
  4. To exit Weather Radio broadcast mode, press the [EXIT] key or [PTT] key.
Baofeng UV-17 Pro Max highlighting 10 NOAA weather stations
Figure 9: The radio's capability to receive 10 NOAA weather stations and FM Radio.
Weather Channel Frequencies and Names
Channel Number RX Frequency MHz Channel Number RX Frequency MHz
Wx-01162.550Wx-06162.500
Wx-02162.400Wx-07162.525
Wx-03162.475Wx-08161.650
Wx-04162.425Wx-09161.775
Wx-05162.450Wx-10163.275

NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

Working the Menu System

For a complete reference on available menu items and parameters, see Appendix B, Menu definitions in the original PDF manual. If your radio is set to Memory (MR) mode, the following menu items will not take any effect: STEP, TXP, W/N, CTCSS, DCS, S-CODE, PTT-ID, BCL, SFT-D, OFFSET, MEM-CH.

Basic Use of Menu
  1. Press the [MENU] key to enter the menu.
  2. Use the UP and DOWN keys to navigate between menu items.
  3. Once you find the desired menu item, press [MENU] again to select it.
  4. Use the UP and DOWN keys to select the desired parameter.
  5. To confirm your selection, press [MENU] to save and return to the main menu. To cancel changes, press [EXIT] to reset and exit the menu.
  6. To exit the menu at any time, press the [EXIT] key.
Using Menu Shortcuts

Every menu item has a numerical value for direct access. The menu is organized with the ten most common functions on top.

  1. Press the [MENU] key to enter the menu.
  2. Use the numerical keypad to enter the number of the menu item.
  3. To enter the menu item, press the [MENU] key.
  4. For entering the desired parameter, use the arrow keys or the numerical keypad for the shortcut code.
  5. To confirm your selection, press [MENU] to save and return to the main menu. To cancel changes, press [EXIT] to reset and exit the menu.
  6. To exit the menu at any time, press the [EXIT] key.

Scanning

The radio features a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels. To enable the scanner, press and hold the [#] key for about two seconds. Press and hold the [#] key again to exit scanning mode.

Scanning Modes

The scanner is configurable to one of three ways: Time, Carrier, or Search.

  1. Time Operation (TO): Scanner stops when it detects a signal, then resumes scanning after a preset time.
  2. Carrier Operation (CO): Scanner stops when it detects a signal, then resumes scanning after a preset time with no signal.
  3. Search Operation (SE): Scanner stops when it detects a signal. To resume scanning, you must press and hold the [#] key again.
Setting Scanner Mode
  1. Press the [MENU] key.
  2. Enter "21" on the numeric keypad for scanner mode.
  3. Press the [MENU] key to select.
  4. Use UP/DOWN keys to select scanning mode (TO, CO, or SE).
  5. Press the [MENU] key to confirm and save.
  6. Press the [EXIT] key to exit the menu.

Frequency Scanning

In frequency mode, press [#] key for more than 2 seconds. The radio will start scanning according to the set frequency step. You can change the scanning direction with the UP/DOWN keys. Press [#] key to stop scanning.

Channel Scanning

In channels mode, press [#] key for more than 2 seconds. The radio will start scanning according to the channel you set. You can change the scanning direction with the UP/DOWN keys. Press [#] key to stop scanning.

Scan CTCSS / DCS

These functions allow scanning frequencies with CTCSS tone or DCS code enabled.

  • Scan CTCSS: In standby, press [MENU] then [1][4]. "Scan CTCSS" will appear. Press [MENU] to start scanning.
  • Scan DCS: In standby, press [MENU] then [1][5]. "Scan DCS" will appear. Press [MENU] to start scanning.

Note: These functions cannot be activated in Channel mode. Scanning starts only when the receiving band detects a signal.

Manual Programming (Channels Memory)

Memory channels store commonly used frequencies for easy retrieval. The radio features 999 memory channels, each capable of holding receive/transmit frequencies, transmit power, group signaling, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.

Frequency Mode (VFO): Used for temporary frequency assignments or quick field programming.

Channel Mode (MR): Used for selecting preprogrammed channels.

To program a channel, switch to VFO mode, enter the desired RX and TX frequencies, and any CTCSS/DCS tones. Then, save to a memory channel using the menu options. Refer to the original PDF manual for detailed examples (Appendix B, Menu definitions).

Repeaters Programming

These instructions assume you know your repeater's transmit and receive frequencies and are authorized to use it.

  1. Press and hold the [VFO/MR] key to set the radio to VFO mode.
  2. Use the numeric keypad to enter the repeater's output (your receiving) frequency.
  3. Press the [MENU] key.
  4. Enter [2][9] for frequency offset. Press [MENU] to select.
  5. Use the numerical keypad to enter the specified frequency offset.
  6. Press [MENU] to confirm and save.
  7. Enter [2][8] for offset direction. Use UP/DOWN keys to select + (positive) or - (negative) offset.
  8. Press [MENU] to confirm and save.
  9. (Optional) Save to memory or set up CTCSS.
  10. Press [EXIT] to exit the menu.

VOX (Voice Operated Transmit)

This function allows hands-free conversations. Speak into the microphone to activate communication. In standby mode, press [MENU] + 7. The screen displays "VOX". Press [MENU] to enter. Press UP/DOWN keys to turn ON/OFF VOX or select level (1-10). Press [MENU] to confirm. Press [EXIT] to return to standby. Level 1 is least sensitive, 9 is most sensitive. VOX is not enabled in Scan or FM Radio mode.

Dual Watch

The radio features Dual Watch functionality (single receiver) to monitor two channels. It can flip-flop between two frequencies at a fixed interval. To enable/disable: Press [MENU], enter 7, press [MENU], use UP/DOWN keys to enable/disable, press [MENU] to confirm, then [EXIT] to exit.

Stopwatch Timer

In standby mode, press [MENU] + 44. The screen displays "STOP WATCH". Press [MENU] to enter. Press UP/DOWN keys to enable (ON), then [MENU] to confirm. To start counting, press [MENU]. Press [MENU] again to restart. To exit, stop counting first, then press [EXIT].

Scrambler

The scrambler protects communications by preventing others from understanding your voice. In standby mode, press [MENU] + 45. The screen displays "SCRAMBLE". Press [MENU] to enter. Press UP/DOWN keys to select scramble mode (MODE1 to MODE3). The "SCR" icon will appear on the display.

DTMF (Dual-Tone Multi-Frequency)

DTMF is an in-band signaling method using dual sinusoidal signals. In two-way radio systems, it's used for automation and remote control, such as activating amateur radio repeaters. The radio has full DTMF implementation, including A, B, C, and D codes. Numeric keys and [*], [#], UP, DOWN keys correspond to DTMF codes. To send DTMF codes, press the corresponding key(s) while holding down the PTT key. If keypad lock is enabled, you can still send DTMF tones.

DTMF Frequencies and Corresponding Codes
1209Hz 1336Hz 1477Hz 1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

Customization

The radio allows you to define visual and audible features to suit your usage habits.

  • Display backlight (ABR) - MENU 7: Set the delay time for the LCD backlight (ON/5sec/10sec/15sec/20sec).
  • Beep PROMPT (BEEP) - MENU 8: Enable/disable the beep tone when a key is pressed.
  • Voice function (VOICE) - MENU 17: Enable/disable voice prompts.
  • Language of the MENU (LANGUAGE) - MENU 18: Select menu language (English/Chinese).
  • Working Mode (MDF-A) - MENU 24: Choose between Frequency mode (FREQ), Channel mode (CH), or Channel name (NAME) display.
  • Roger Beep, end Transmission Tone (ROGER) - MENU 36: Enable/disable a tone at the end of transmission.
  • Power On Message (POWER ON MSG) - MENU 40: Customize the welcome message displayed on startup (VOLTAGE, MESSAGE, LOGO, MODEL NAME).
  • Power On Password (POWER ON PWD) - MENU 43: Enable a password requirement when turning on the radio.

Reset - MENU 42

This transceiver has two Reset modes:

  • Reset VFO: All settings except channels return to default.
  • Reset ALL: All settings return to default.

To perform a reset: In standby, press [MENU] + 42. The screen displays "RESET". Press [MENU], use UP/DOWN keys to select VFO or ALL, then press [MENU] to confirm. The display will show "Sure to reset?". Press [MENU] again to confirm. The transceiver will turn off and reboot.

Shortcut Menu Operations Table

For a detailed list of all menu items, their settings, and descriptions, please refer to the table below. This table provides quick access and understanding of the radio's customizable functions.

MENU Name (Full Name) Settings Description
0SQL - Squelch Level[0-9] Setting the squelch to 0 will open up the squelch entirely.Squelch silences the receiver when there is no signal. Sensitivity can be varied from .1 to .3 mV on UHF, and .1 to .2 mV on VHF.
1STEP - Step Frequency2.5K[0] | 5.0K[1] | 6.25K[2] | 10.0K[3] | 12.5K[4] | 20.0K[5] | 25.0K[6] | 50.0K[7]Selects the amount of frequency change in VFO/Frequency mode when scanning or pressing the UP/DOWN keys.
2TXP - Transmit PowerHIGH [0] | LOW [1]Selects between HIGH and LOW transmitter power in VFO/Frequency mode. Use the minimum transmit power necessary.
3SAVE - Battery SaveOFF [0] | 1 | 2 | 3 | 4Selects the ratio of sleep cycles to awake cycles (1:1, 2:1, 3:1, 4:1). Higher numbers increase battery life but may miss syllables.
4VOX - Voice Operated TXOFF [0] | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10When enabled, no need to press PTT. Adjust gain level for smooth transmission.
5WN - Wideband / NarrowbandWIDE [0] | NARR [1]Wideband (25 kHz bandwidth) or narrowband (12.5 kHz bandwidth).
6ABR - Display Illumination TimeON [0] | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10Time-out for the LCD backlight. (seconds)
7TDR - Dual Watch, Dual ReceptionOFF [0] | ON [1]Monitor A and B at the same time. Display with most recent activity becomes selected.
8BEEP - Keypad BeepOFF [0] | ON [1]Allows audible confirmation of a key press.
9TOT - Transmission Time-out-TimerOFF [0] 15[1] - 180[12] in 15 second steps (TIMEOUT-15)/15=[n]Limits transmission time to a programmed value for battery conservation and to prevent interference.
10R-CTCS - Receiver CTCSSOFF [0] | see CTCSS Table in Appendix CMutes speaker in absence of specific continuous sub-audible signal.
11R-DCS - Receiver DCSOFF [0] | see DCS Table in Appendix CMutes speaker in absence of specific low-level digital signal.
12T-CTCS - Transmitter CTCSSOFF [0] | see CTCSS Table in Appendix CTransmits specific sub audible signal to unlock squelch of distant receiver (repeater).
13T-DCS - Transmitter DCSOFF [0] | see DCS Table in Appendix CTransmits specific low-level digital signal to unlock squelch of distant receiver (repeater).
14Scan CTCSSOFFAllows scanning of CTCSS in VFO frequency mode. Not allowed in channel mode.
15Scan DCSOFFAllows scanning of DCS in VFO frequency mode. Not allowed in channel mode.
16CDCSS SAVE MODEALL[0] | RX[1]|TX[2]Save scanned CTCSS/DCS in VFO mode. ALL: Save to R-CDCSS and T-CDCSS. TX: Save to T-CDCSS only. RX: Save to R-CDCSS only.
17VOICE - Voice PromptOFF [0] | ON [1]Allows audible voice confirmation of a key press.
18LANGUAGE - Language selectionENGLISH [0] | 中文[1]Set the language type of menu and prompt voice. ENGLISH: Display English menu/prompts. Chinese: Display Chinese menu/prompts.
19DTMFST - DTMFSTOFF [0]: No DTMF Side Tones. DT-ST [1]: Side Tones from manually keyed DTMF codes. ANI-ST [2]: Side Tones from automatically keyed DTMF codes. DT+ANI [3]: All DTMF Side Tones.Determines when DTMF Side Tones can be heard from the transceiver speaker.
20S-CODE - Signal Code1[0] | 2[1] | ... | 15[14]Selects 1 of 15 DTMF codes. Programmed with software, up to 5 digits each.
21SC-REV - Scanner Resume MethodTO [0]: Time Operation - scanning resumes after fixed time. CO [1]: Carrier Operation - scanning resumes after signal disappears. SE [2]: Search Operation - scanning will not resume.Scanning Resume Method.
22PTT-ID - When to send the PTT-IDOFF [0]: No ID sent. BOT [1]: S-CODE sent at beginning. EOT [2]: S-CODE sent at ending. BOTH [3]: S-CODE sent at beginning and ending.When to Send PTT-ID Codes are sent during either the beginning or ending of a transmission.
23PTT-LT - Signal code sending delay0[0] | 100[1] | 200[2] | 400[3] | 600[4] | 800[5] | 1000[6]PTT-ID Delay (milliseconds).
24MDF-A - Channel Mode A DisplayCH [0]: Displays channel number. NAME [1]: Displays channel name. FREQ [2]: Displays programmed Frequency.MR/Channel Mode Display Format for A. Names must be entered using software.
25MDF-B - Channel Mode B DisplayCH [0]: Displays channel number. NAME [1]: Displays channel name. FREQ [2]: Displays programmed Frequency.MR/Channel Mode Display Format for B. Names must be entered using software.
26BCL - Busy Channel Lock-outOFF [0] | ON [1]Disables PTT key on a channel already in use. Transceiver beeps and will not transmit.
27AUTOLK - Automatic Keypad LockOFF [0] | 5 [1] | 10 [2] | 15 [3]Sets automatic keyboard lock delay time. Prevents accidental triggering. Keypad locks if unused for predetermined time. Press [*] for 2 seconds to unlock.
28SFT-D - Frequency Shift DirectionOFF [0]: TX=RX (simplex). + [1]: TX shifted higher. - [2]: TX shifted lower.Enables access of repeaters in VFO/Frequency Mode.
29OFFSET - Frequency shift amount00.000 - 69.990 in 10 kHz stepsSpecifies the difference between the TX and RX frequencies.
30MEMCH - Store a Memory Channel001-999Create new or modify existing channels (001-999) for MR/Channel Mode.
31DELCH - Delete a memory channel001-999Delete programmed information from specified channel.
32AL-MOD - Alarm ModeSITE [0]: Sounds alarm through radio speaker only. TONE[1]: Transmits cycling tone over-the-air. CODE [2]: Transmits '119' (911 in reverse) followed by ANI code.SITE: Sounds alarm through radio speaker only. TONE: Transmits cycling tone over-the air. CODE: Transmits '119' (911 in reverse?) followed by ANI code over-the-air.
33STE - Squelch Tail EliminationOFF [0] | ON [1]Eliminates squelch tail noise between Baofeng handhelds communicating directly. Reception of 55 Hz or 134.4 Hz tone burst mutes audio.
34RP-STE - Squelch Tail EliminationOFF [0] | 1 - 10Eliminates squelch tail noise when communicating through a repeater.
35RPT-RL - Delay the squelch tail of repeaterOFF [0] | 1 - 10Delay the Tail Tone of Repeater (X100 milliseconds).
36ROGER - Roger BeepOFF [0] | ON [1]Sends an end-of-transmission tone to indicate to other stations that transmission has ended.
37TONE-Tone-burst1000[0]|1450[1]|1750[2]|2100[3]To send a tone-burst, simultaneously press a key while holding down the PTT. No further configuration needed.
38MENU EXIT TIME5 [0] 10[1]-60[10] in 5 second steps (TIMEOUT-5)/5=[n]The time setting for menu exit without menu operation.
39VOX DELAY0.5 [0] 0.6[1] -2.0[15] in 0.1 second steps (TIMEOUT-0.1)/0.1=[n]Brief delay between finishing talking and radio returning to TX mode; this delay is adjustable.
40POWER ON MSG - Power On MessageLOGO[0] | VOLTAGE[1]Welcome message displayed immediately after startup. LOGO is programmed by the manager.
41VOICEPRI - Frequency hopping systemOFF [0] | ON [1]Activate frequency hopping function to prevent interference from outside the group.
42RESET - Restore defaultsVFO [0] | ALL [1]Resets the radio to factory defaults, with some exceptions.
43POWER ON PWD - Power on passwordOFF [0] | ON [1]Activate radio power-on password. Must enter correct password to turn on radio.
44STOP WATCHONActivate stopwatch function. Press [MENU] key to start timing.
45SCRAMBLEOFF [0] | ON [1]Scramble is voice inversion function for private communication. SCR icon displayed when enabled.
46VERSION - Version informationAccess hardware and firmware information for the radio.

4. Maintenance

4.1 Battery Maintenance Instructions

To help your battery work normally or prolong its life, observe the following instructions:

  1. Accumulated dust on the charging connector may affect normal charging. Use a clean and dry cloth to wipe it regularly.
  2. It is recommended to charge the battery under 5°C-40°C. Violation of this limit may cause battery life reduction or leakage.
  3. To charge a battery attached to the product, turn it off to ensure a full charge.
  4. Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
  5. Do not dispose of the battery in fire.
  6. Do not expose the battery to direct sunlight for a long time, nor place it close to other heating sources.
  7. Do not squeeze and penetrate the battery, nor remove its housing.

4.2 Transportation Instructions

  1. Damaged batteries must not be transported.
  2. To avoid short circuit, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
  3. The radio must be switched off and secured against switch-on if the battery is attached.

The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for local regulations and further information.

4.3 Radio Maintenance

Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to enjoy this product for many years.

  • Do not attempt to open the radio for any reason! The radio's precision mechanics and electronics require experience and specialized equipment. The radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty.
  • Do not store the Radio under the sunshine or in hot areas.
  • High temperatures can shorten the life of electronic devices and warp or melt certain plastics.
  • Do not store the radio in dusty and dirty areas.
  • Keep the Radio dry. Rainwater or damp will corrode electronic circuits.
  • If the Radio emits a peculiar smell or smoke, immediately shut off its power and remove the charger or battery.
  • Do not transmit without an antenna.

5. Troubleshooting Guide

Phenomena Analysis Solution
You cannot turn on the radio. The battery may be installed improperly.
The battery power may run out.
The battery may suffer from poor contact caused by dirty or damaged battery contacts.
Remove and reattach the battery.
Recharge or replace the battery.
Clean the battery contacts or replace the battery.
During receiving, the voice is weak or intermittent. The battery voltage may be low.
The volume level may be low.
The antenna may be loose or improperly installed.
The speaker may be blocked.
Recharge or replace the battery.
Increase the volume.
Turn off the radio, then remove and reattach the antenna.
Clean the surface of the speaker.
You cannot communicate with other group members. The frequency or signaling type may be inconsistent.
You may be too far away from other members.
Verify TX/RX frequency and signaling type are correct.
Move towards other members.
You hear unknown voices or noise. You may be interrupted by radios using the same frequency.
The radio in analog mode may be set with no signaling.
You may be too far away from other members.
Change the frequency, or adjust the squelch level.
Request your dealer to set signaling for the current channel.
Move towards other members.
You are unable to hear anyone because of too much noise and hiss. You may be in an unfavorable position (blocked by high buildings or underground area).
It may be the result of external disturbance (electromagnetic interference).
Move to an open and flat area, restart the radio, and try again.
Stay away from equipment that may cause interference.
The radio keeps transmitting. VOX may be turned on or the headset is not installed in place. Turn off the VOX function. Check that the headphones are in place.

NOTE: If the above solutions cannot fix your problems, or you have other queries, please contact your dealer for more technical support.

6. Technical Specifications

General
Frequency Range136-174MHz(TX&Rx), 220-260MHz(TX&Rx), 400-520 MHz(TX&Rx), FM65-108MHz(Rx), AM108-136MHz(Rx), Police350-390MHz(Rx)
Power10W/2W
Channel Spacing25.0KHz(Wide)/12.5KHz(Narr)
Memory Channel999 Groups
Operation VoltageDC 7.4 V ±10%
Transmission current<High-Capacity
Receive Sensitivity0.25μV (12dB SINAD)
Rated Audio Power Output1W @16 ohms
Receive current≤380mA
Connection for accessories2 pin Kenwood jack
Antenna impedance50 Ohm

NOTE: All specifications may be modified without prior notice or liability.

7. User Tips

  • The radio offers great power and frequency ranges, with very good audio for both transmission and reception.
  • The menu system is intuitive, making the radio easy to operate and configure.
  • The devices are generally of good quality and easy to program.

8. Frequently Asked Questions (FAQ)

Q: Does this radio come with GPS?
A: No, this model does not include GPS functionality.
Q: Which model is the large antenna for?
A: The manual refers to a standard antenna included with the BF-17 P.M Series. Specific models for larger antennas would depend on aftermarket accessories.

9. Warranty and Support

9.1 Disclaimer

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company. We do not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy, or completeness of the third-party products and contents involved in this manual.

9.2 User Manual PDF

A detailed user manual in PDF format is available for download. This document contains comprehensive instructions and diagrams for advanced features and troubleshooting. You can access the PDF at: User manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.