Hi-Link HLK-7688A

Contents

Hi-Link HLK-7688A WiFi Router Module User Manual

Model: HLK-7688A

1. Introduction

The HLK-7688A is a low-cost, low-power consumption IoT module developed by Hi-Link, based on the MT7688AN chipset. This module supports Linux and OpenWrt operating systems, offering extensive customization and development possibilities. It is designed for integration into smart devices and cloud service applications, featuring a rich set of interfaces and powerful processing capabilities.

Key Features:

  • 150Mbps Wi-Fi (802.11b/g/n)
  • Supports AP, STA, and AP+STA mixed modes
  • Five 10/100M Ethernet ports
  • One USB2.0 Host interface port
  • Rich peripheral interfaces: SPI, I2C, I2S, PCM, UART, JTAG, GPIO
  • Inbuilt powerful PMU (Power Management Unit)
  • Supports Linux 2.6.36 SDK and OpenWrt 3.10

2. Setup

This section outlines the basic steps for setting up your HLK-7688A module. As a development module, proper connection to a host system or development board is crucial.

2.1. Power Supply

The HLK-7688A module requires a stable 3.3V DC power supply. Ensure your power source can provide sufficient current for the module's operation and any connected peripherals.

  • VBAT (Power voltage): Minimum 3V, Typical 3.3V, Maximum 3.6V
  • I/O (I/O voltage): Minimum 3V, Typical 3.3V, Maximum 3.6V

2.2. Pin Definitions and Connections

Understanding the module's pinout is essential for correct integration. Refer to the pin definition diagram and table below for detailed information.

HLK-7688A Default Pin Definition Diagram

Figure 1: HLK-7688A Default Pin Definition Diagram

HLK-7688A Typical Peripheral Interfaces Diagram

Figure 2: HLK-7688A Typical Peripheral Interfaces

Important Pin Notes:

  • The middle three pads on the module are hot pads and must be grounded for proper operation and heat dissipation.
  • All pins are configured to their default functions upon power-up.

2.3. Antenna Connection

The module supports an IPEX connector for an external antenna. Ensure a compatible 2.4GHz antenna is connected for optimal Wi-Fi performance.

2.4. Initial Firmware and SDK

The HLK-7688A comes with OpenWrt pre-installed. For development, utilize the provided Linux 2.6.36 SDK. Initial setup typically involves connecting via UART for console access to configure network settings or flash custom firmware.

3. Operating

Operating the HLK-7688A involves interacting with its OpenWrt environment and utilizing its various interfaces.

3.1. Accessing OpenWrt

Typically, you can access the OpenWrt command-line interface (CLI) via the UART interface. Connect a USB-to-UART converter to the module's UART TXD0 and RXD0 pins (and GND) and use a terminal emulator (e.g., PuTTY, Tera Term) with a baud rate of 115200bps.

3.2. Network Configuration

Once logged into OpenWrt, you can configure the Wi-Fi (AP/STA mode), Ethernet ports, and other network settings using standard OpenWrt commands (e.g., uci commands) or by accessing the LuCI web interface if enabled and configured.

3.3. Utilizing Peripherals

The module exposes various interfaces for connecting external components:

  • GPIO: General Purpose Input/Output pins for controlling external devices.
  • UART: Serial communication for debugging or connecting to other microcontrollers.
  • I2C/SPI: For communicating with sensors, displays, and other ICs.
  • Ethernet: Five 10/100M ports for wired network connectivity.
  • USB2.0: For connecting USB devices like storage, cameras, or other peripherals.

3.4. Firmware Development

Developers can build custom firmware using the provided SDK, allowing for tailored applications and functionalities. This involves cross-compilation and flashing the new firmware onto the module's flash memory.

Video 1: HLK-7688A Product Overview

4. Maintenance

Proper care and maintenance can extend the lifespan and ensure reliable operation of your HLK-7688A module.

  • Environmental Conditions: Operate the module within its specified temperature range (-20°C to 60°C) and humidity (0-85% non-condensing). Avoid exposure to extreme temperatures, direct sunlight, moisture, and corrosive environments.
  • Handling: Handle the module with care, especially when connecting or disconnecting wires. Avoid applying excessive force to the pins or the module itself. Use anti-static precautions when handling to prevent electrostatic discharge (ESD) damage.
  • Cleaning: If necessary, gently clean the module with a soft, dry, anti-static cloth. Do not use liquids or harsh chemicals.
  • Firmware Updates: Regularly check for official firmware updates from Hi-Link or the OpenWrt community to benefit from bug fixes, security patches, and new features. Follow official guidelines for firmware flashing to avoid bricking the device.

5. Troubleshooting

If you encounter issues with your HLK-7688A module, consider the following troubleshooting steps:

  • No Power/No Boot:
    • Verify the 3.3V power supply is stable and correctly connected to the VBAT and GND pins.
    • Check for any short circuits on the power lines.
    • Ensure the module is correctly seated if using a development board.
  • No Wi-Fi Connectivity:
    • Confirm the external antenna is properly connected to the IPEX connector.
    • Check Wi-Fi configuration in OpenWrt (SSID, password, operating mode).
    • Ensure the Wi-Fi radio is enabled.
  • No Console Output (UART):
    • Verify UART connections (TXD0, RXD0, GND) and ensure they are not swapped.
    • Check the baud rate (115200bps), data bits (8), parity (none), stop bits (1) in your terminal emulator.
    • Ensure your USB-to-UART converter drivers are correctly installed.
  • Module Not Responding:
    • Try a hard reset by power cycling the module.
    • If firmware corruption is suspected, you may need to re-flash the firmware via a recovery method (e.g., TFTP bootloader).

6. Specifications

Detailed technical specifications for the HLK-7688A module:

ParameterValue
ModelHLK-7688A
ChipsetMT7688AN
KernelMIPS24KEc
Basic Frequency580MHz
RAMDDR2 128MB
Flash32MB
Wireless ProtocolIEEE802.11bgn
Transfer Speed150Mbps
Firmware VersionOpenWrt
Baud Rate (UART)115200bps
Transmit Power15-20dBm
Channels1-14
InterfacesUART, GPIO, I2C, PWM, SPI, Ethernet, USB2.0, I2S, JTAG, SDXC
Operating Temperature-20°C ~ 60°C
Operating Humidity0-85% (non-condensing)
Dimensions18mm × 32.8mm × 2.8mm
HLK-7688A Module Dimensions Diagram

Figure 3: HLK-7688A Module Dimensions

7. User Tips

  • Pinout Clarity: Always double-check your connections against the detailed pinout diagram and table. Incorrect wiring can damage the module or connected components. If using a test board, ensure you have its specific pinout documentation as well.
  • Grounding Hot Pads: Remember to properly ground the three central hot pads on the module for stable operation and thermal management.
  • Start Simple: When beginning development, start with basic functionalities like UART communication and Wi-Fi setup before integrating complex peripherals.
  • Consult OpenWrt Resources: Leverage the extensive documentation and community support available for OpenWrt for configuration and development guidance.

8. Warranty and Support

For warranty information, please refer to the terms and conditions provided by your seller or distributor at the time of purchase. Technical support and further documentation, including detailed datasheets and SDK guides, can typically be found on the Hi-Link official website or by contacting their support channels.

A comprehensive user manual in PDF format is available for download: HLK-7688A User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.