1. Introduction
This manual provides essential information for the safe and effective use of your RASTP High Flow Air Intake Filter. Designed to enhance engine performance by increasing airflow and improving throttle response, this filter is a direct replacement for aftermarket intake systems. Please read all instructions carefully before installation and operation.
2. Safety & Warnings
Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord (if any) out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture unless specifically instructed for cleaning.
- Handle with care to avoid cuts or injuries.
3. Setup and Installation
Professional installation is highly recommended for this product to ensure proper fitment and optimal performance. The filter features a clamp-on design for direct bolt-on installation.
For a visual guide on product handling and general appearance, please refer to the video below:
Video: Product unboxing and handling demonstration.
The filter is designed to fit into the air inlet system with a neck size of 70mm (2.76"). Ensure the connector inside diameter matches your vehicle's intake system.
Image: RASTP Air Intake Filter installed in an engine bay.
Image: Close-up views of the air filter's top, bottom, and clamp mechanism.
4. Operating Instructions
The RASTP High Flow Air Intake Filter is designed to draw more air into your engine, improving throttle response and enhancing horsepower. Its fine mesh construction increases the amount of airflow and straightens the flow, preventing the engine from sucking hot air from the high-temperature engine compartment. This results in an instant gain of 5-8 horsepower by optimizing the filtration process.
Image: Diagram illustrating cold air intake, fresh air output, and filter benefits.
Image: Benefits of the round tapered cone intake filter design.
5. Maintenance
The RASTP Air Intake Filter features a washable and reusable filter cartridge, offering an economical and practical alternative to disposable filters. Regular maintenance ensures optimal performance and longevity.
- Cleaning: The filter can be cleaned with water. After washing, ensure the filter is completely dry before reinstallation to prevent damage to your engine.
- Inspection: Always inspect the filter for any damage or wear before each use. If the filter appears damaged, replace it immediately.
- Storage: If removing the filter for extended periods, turn off the device (vehicle) and store the filter in a dry place, away from children.
Image: Air filter demonstrating its washable and durable design.
6. Troubleshooting
- Engine Light Activation: If an engine warning light appears after installation, ensure your vehicle's engine control unit (ECU) is properly mapped for the new air intake system. Alternatively, if the filter is part of an open air intake, ensure the airbox cover is re-installed correctly to prevent issues.
- Reduced Performance: If you notice a decrease in performance, check the filter for excessive dirt or damage. Clean or replace as necessary. Ensure all connections are secure and airtight.
7. Specifications
| Feature | Detail |
|---|---|
| Product Name | Intake Air Filter |
| Model Number | E-2993 (RS-OFI106) |
| Application | For Ford Focus, Escape, MKC |
| Placement on Vehicle | Intake System |
| Connector Inside Diameter | 70mm (2.76") |
| Outer Diameter (OD) | 80mm (3.14") |
| Item Length | 210mm (8.27") |
| Bottom Diameter | 156mm (6.14") |
| Item Weight | 0.625kg |
| Material | Dry spunlace non-woven fabric, iron, rubber, stainless steel |
| Color | Red |
| Country/Region of Manufacture | China |
Image: Dimensions of the RASTP Air Intake Filter.
8. User Tips
- Engine Light Prevention: If installing in a Ford Focus MK2, ensure your engine's ECU is properly re-mapped or that the original airbox cover is re-installed if not using a full cold air intake system, to prevent an engine warning light from appearing.
- Filter Oiling: The filter is made from dry spunlace non-woven fabric. It is generally a dry filter type. If you prefer to oil your filter for enhanced filtration, please consult a professional or refer to specific instructions for compatible filter oils.
- Cleaning & Drying: While the filter is washable with water, always ensure it is thoroughly dry before re-installation to avoid potential engine issues.
- Size Verification: Always double-check the size measurements against your vehicle's requirements before purchase and installation to ensure a perfect fit.
9. Warranty & Support
For further item guides and documents, please refer to the official user manual PDF available from the seller.
Manufacturer Information:
- Manufacturer: Ruian Lingsheng Auto Parts Co., Ltd
- Address: Fuzhou West Road, Xiacun Industrial Zone, Xincheng Street, Ruian City, Zhejiang Province, China
- Contact: 3219289207@qq.com, +86-15168772293
EU Authorized Representative:
- Representative: MJCM SARL
- Address: 78 avenue des Champs Elysees Bureau 326, PARIS France
- Contact: mjcm190928@gmail.com, +33-767213611