ludengchaoshi Vintage Chandelier Remote Control Ceiling Fan

Contents

Vintage Chandelier Remote Control Ceiling Fan with LED Light

Model: Vintage Chandelier Remote Control Ceiling Fan

Brand: ludengchaoshi

1. Introduction and Safety Instructions

Please read this manual thoroughly before installation and use. Keep it for future reference. This appliance is designed for indoor use only.

General Safety Warnings:

  • This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure they do not play with the appliance.
  • WARNING: If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent, or suitably qualified persons.
  • The replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent, or suitably qualified persons.
  • If it is necessary to replace the live or neutral brushes to ensure operation of the motor, then both brushes and the earth brush shall be replaced at the same time. The brushes shall only be replaced by a suitably qualified person.

Electrical Safety:

  • To reduce the risk of electric shock, the supply line must be connected between the fan and an all-pole disconnect switch. The switch contacts must have an opening distance of at least 3mm. If you lack electrical knowledge, ensure installation is performed by a professional with an electrician's license.
  • To avoid electrical shock hazards, turn off the power before installing or removing the ceiling fan.
  • Wiring order: Ground, FireWire, Zero line. Disassembly must be in reverse order: Zero line, FireWire, Earth.
  • Do not use non-local governors or switches with this product.
  • The power of this machine is 220V/550Hz.
  • The maximum motor power is 75W (may vary by model). Each light source lamp has a maximum of 60W.

Installation Safety:

  • Ensure all screw parts are securely latched during installation.
  • When the ceiling fan is rotating, the blades should not touch any object to avoid danger.
  • Select an appropriate location for installation. The ceiling fan blades should be at least 2.3 meters above the ground to prevent accidental blade collision.

2. Product Overview

This ceiling fan combines efficient air circulation with integrated LED lighting, controlled conveniently by a remote. It features a modern design suitable for various living spaces.

High Wind Ceiling Fan with Remote Control

Figure 2.1: High Wind Ceiling Fan with Remote Control. Features wide area circulating wind.

Key Features:

  • Dual Modes: Forward airflow for summer cooling, reverse airflow for winter air circulation.
  • Adjustable Lighting: 3-color change light (White, Neutral, Warm Light).
  • 6-Speed Regulation: Customize airflow to your preference.
  • Remote Control: Convenient operation of fan speed, light, and modes.
  • Durable Construction: Features a pure copper motor and ABS fan blades.
  • Transparent Lampshade: Ensures optimal light distribution.
Illustration of 3-color light options: White, Neutral, Warm Light

Figure 2.2: Light color options: White Light, Neutral Light, Warm Light.

Diagram explaining dual modes for Summer (forward airflow downward) and Winter (reverse airflow upward for air circulation)

Figure 2.3: Dual modes for Summer (forward airflow downward) and Winter (reverse airflow upward for air circulation).

Components:

The product package includes the following main components:

Diagram highlighting key components: Pure Copper Motor, Large Fan Blade, Transparent Lampshade

Figure 2.4: Key components: Pure Copper Motor, Large Fan Blade, Transparent Lampshade.

No. Part Name
1 Ceiling fan body (including motor, housing, switch boxes)
2 Hanger
3 Bell
4 Hanging tube assembly
5 Glass shade
6 Leaf frame
7 Splice closure
8 Lamp units
9 Blade
10 Parts screw package (expansion screws, wood screws, flat washers, siring tablets, sling bag, balanced package, leaf frame screws package, blade screw package)

3. Installation Guide

Follow these steps carefully for proper installation. Professional installation is highly recommended for electrical wiring.

3.1. Hanger Locking Mode

NOTE: Do not install the hanger on a roof that is leaking or damp. The hanger must be able to withstand a weight of 40 kg or more to prevent hazards.

  • For Concrete Ceilings: Drill holes (distance between holes should be appropriate) and insert expansion screws. Secure the hanger with expansion screws, flat washers, and nuts using a spanner wrench.
  • For Wooden Ceilings: Secure the hanger to the ceiling using wood screws and flat washers. Ensure the ceiling-mounted hanger is firmly attached.

3.2. Suspension System Installation

Connect the housing boom through the bell. Align the lifting boom head and holes, then insert the pin and R pin through the bolt holes. Screw on the side of the head hanging locking. Hang the ceiling fan on the hanger, ensuring the hanger slot aligns with the card.

3.3. Power Cord Connection

Hang up the fan according to the wiring diagram. Connect the wires corresponding to the line. The fixed wiring must be connected with a contact separation of at least 3mm all-pole disconnect device.

Typical Wiring (Consult a professional electrician if unsure):

  • Ground wire: Yellow-Green
  • Lamps Fire Wire: Blue
  • Fan Fire Wire: Black
  • Input Fire Wire
  • Input Zero Line

For a 4-wire setup (Black=Hot, Red=Hot, White=Neutral, Copper=Ground), typically:

  • Connect the fan's 'FireWire' (Black) to your household 'Hot' (Black or Red).
  • Connect the fan's 'Zero line' (White) to your household 'Neutral' (White).
  • Connect the fan's 'Ground' (Yellow-Green) to your household 'Ground' (Copper).
  • If there are separate wires for fan and light, ensure they are connected to appropriate switched hot lines if independent control is desired.

3.4. Locking Bell and Blade Installation

  • Align the bell cast hanger, hanger hole, and side holes, then align the bell and lock the screws.
  • Align the Yasha and blade alignment holes, then tighten the screws.
  • Align the fork hole leaf blade and lock Yasha bit with the holes of the motor and the screw holes on the lock.

3.5. Lighting Installation

Installation varies slightly depending on whether it's a multi-light or single-lamp series.

For Multi-Light Installation:

  1. Connect the fixture's white and blue lines to the switch box's white and blue lines. Tighten the bonnet and lock the shade.
  2. Neatly finish the lamp lines into the switch box. Ensure the notch on the cover aligns with the switch box.
  3. Loosen the screws on the lamp cup by hand. Set the glass shade lamp cup and hand-tighten the three screws on the side of the lamp cup. Ensure screws are firmly in place but not overtightened to avoid breaking the glass.

For Single Lamp Installation:

  1. Remove the switch cover and connect the lamp cover.
  2. Replace the cover under the switch to the switch box.
  3. Replace the lamp. Loosen the lamp panel on three screws, fit with glass, and then tighten the screws.
  4. Alternatively, sequentially install lampshades, decorative covers, and decorative head through the chain. The ornaments will head lock teeth of sturdy glass.

4. Operation

The ceiling fan is operated via the included remote control. Ensure the remote has working batteries.

Video 4.1: Demonstration of fan light and speed adjustments using the remote control.

Fan Speed and Rotation:

  • Speed Adjustment: Use the remote control to select one of the 6 available speeds.
  • Reverse Rotation (Summer/Winter Modes):
    • To change the fan rotation direction, turn off the fan and wait for the blades to stop turning.
    • Use the reversing switch (usually located on the fan body or accessible via remote) to switch between forward (downward airflow for cooling in summer) and reverse (upward airflow for air circulation in winter) modes.

Light Control:

  • Use the remote control to turn the LED light ON/OFF.
  • Adjust the light color between White Light, Neutral Light, and Warm Light using the remote.

5. Maintenance

Regular Checks:

  • Regularly check the hanger, blade, leaf frame, and various other parts for looseness. Tighten any loose components promptly.

Cleaning:

  • Regularly clean the ceiling fan. Use a soft brush or lint-free cleaning cloth.
  • Do not use a damp cloth or other destructive cleaning agents.
  • Do not clean the ceiling fan blades with water or detergent directly.
  • Before cleaning, ensure the ceiling fan is disconnected from the power switch.

Lubrication:

  • Do not add lubricant to any part of this product.

Blade Balance Check and Adjustment:

If the fan experiences significant shaking:

  1. Review all installation steps to ensure they are correct.
  2. Check that all mounting screws are tight and that the lob slot is correctly engaged.
  3. Verify that all blades are at the same level. Measure the height of each blade from the ceiling to ensure consistency.
  4. If the above methods are ineffective, use the included balance adjustment package. Start by placing the balance clip in the middle of any blade.

Note: Be careful during blade assembly and handling to avoid collision with other objects, which can cause leaf frame deformation.

6. Troubleshooting

Fan Not Rotating:

  1. Check if the ceiling fan's external power supply circuit fuse is blown or if the automatic protection switch is off.
  2. Check for issues with the fan power line contact.
  3. Verify that the fan power supply voltage is normal.

Note: Always ensure the external power is off when checking electrical components. If the issue persists, consult a professional electrical maintenance expert.

Fan Noise:

  1. Check that all fan screws are securely installed and locked.
  2. Check for any friction obstacles with the motor during operation.

Lamp Not Lighting:

  1. Check if the lamp wire port is loose.
  2. Check if the lamp is damaged.

7. Specifications

Attribute Value
Brand Name ludengchaoshi
Item Type Ceiling Fans
Style Modern Style
Installation Method Assembly
Power Source AC
Operating Voltage 220V/550Hz (Max motor power 75W, Max light power 60W)
Control Method REMOTE CONTROL
Switch Type REMOTE CONTROL
Light Source LED
Number of Lights 1 pcs
Is Dimmable No (3-color change light available)
Is Bulbs Included No (Integrated LED)
Luminous Flux 2000-82000
Certification CE, EMC, FCC, GS, ROHS
Origin Mainland China
Material DC silicon steel motor, ABS fan blade
Lighting Lens 24W
Applicable Space 6-12m²
Fan Functions Intelligent timing, 3-color change light, 6-speed regulation, forward and reverse rotation
Wiring and Control 1 Fire 1 Zero, Frequency conversion dual control

Dimensions (for 42-inch model):

Detailed technical specifications and dimensions for the Black walnut -42 inches model

Figure 7.1: Dimensions and specifications for the Black walnut -42 inches model.

  • Unfolded Diameter: 106cm (42 inches)
  • Height: 41cm
  • Lampshade Diameter: 20cm
  • Hanging Rod: Standard 20cm

8. User Tips

  • Handle with Care: Some users have reported damaged blades upon arrival. Always unpack and handle fan blades gently to prevent bending or breaking.
  • Close-up of a damaged fan blade, indicating potential fragility or handling issues

    Figure 8.1: Example of a damaged fan blade. Handle with care during installation.

  • Professional Installation: If the wiring instructions seem unclear or you are not confident with electrical work, it is highly recommended to seek assistance from a qualified electrician. This ensures safety and proper functionality.
  • Check for Balance: If the fan wobbles after installation, refer to the 'Blade Balance Check and Adjustment' section in the maintenance guide.

9. Frequently Asked Questions (FAQ)

Q: Does this fan work on 100V?

A: The power of this machine is specified as 220V/550Hz. Please ensure your electrical supply matches these requirements for proper operation.

Q: How do I connect this fan to my electrical wiring if I have 4 wires (Black=Hot, Red=Hot, White=Neutral, Copper=Ground)?

A: While professional installation is recommended, typically you would connect the fan's 'FireWire' (often Black) to one of your household 'Hot' wires (Black or Red). The fan's 'Zero line' (often White) connects to your household 'Neutral' (White). The fan's 'Ground' (often Yellow-Green) connects to your household 'Ground' (Copper). If your fan has separate wires for the light and fan functions, you may need to connect them to separate switched hot lines for independent control. Always consult a qualified electrician if you are unsure.

10. Warranty and Support

This product comes with a 1-year warranty.

For technical assistance, warranty claims, or any questions not covered in this manual, please contact the manufacturer or your seller directly.

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.