JETTING Shock Absorber Rubber Buffer

Contents

Motorcycle Rear Shock Absorber Rubber Buffer Instruction Manual

Model: Shock Absorber Rubber Buffer

Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your JETTING Motorcycle Rear Shock Absorber Rubber Buffer. Please read this manual thoroughly before installation and retain it for future reference.

Safety Information

Observe the following safety guidelines to prevent damage to the product or injury during installation and use:

  • Keep the product dry and away from direct sunlight.
  • Store in a cool, dry place to maintain the elasticity and integrity of the rubber material.
  • Ensure all components are securely fitted before operating the motorcycle.
  • If you are unsure about any installation steps, consult a qualified mechanic.

Specifications

Feature Detail
Model Shock Absorber Rubber Buffer
Applicable Models Motorcycles, Electric Vehicles
Transmission Type MT/Manual
Material High-quality Rubber, Steel (inner sleeve)
Available Sizes 10mm, 12mm (inner diameter)
Dimensions (approx.) 24mm (width), 20mm (height)
Package Quantity 1 Piece

Note: Due to manual measurement, please allow a slight error of 1-3mm. Actual product color may vary slightly from images due to display differences.

Package Contents

Each package contains:

  • 1 x Shock Absorber Rubber Buffer (selected size: 10mm or 12mm)

Setup and Installation

Follow these steps to install the shock absorber rubber buffer:

  1. Select Appropriate Size: Choose the correct rubber sleeve size (10mm or 12mm) that matches your shock absorber's inner diameter.
  2. Remove Old Components: If applicable, carefully remove the old or worn-out shock absorber buffer from your vehicle.
  3. Install New Buffer: Slide the new rubber buffer onto the shock absorber. Ensure the inner steel pipe aligns correctly with the shock absorber's mounting point.
  4. Secure Fit: Verify that the new rubber buffer is securely seated and fitted properly before using the motorcycle or electric vehicle.
Diagram showing 10mm shock absorber rubber buffer dimensions: 24mm width, 20mm height, 10mm inner diameter.
Figure 1: 10mm Shock Absorber Rubber Buffer Dimensions (24mm width, 20mm height, 10mm inner diameter)
Diagram showing 12mm shock absorber rubber buffer dimensions: 24mm width, 20mm height, 12mm inner diameter.
Figure 2: 12mm Shock Absorber Rubber Buffer Dimensions (24mm width, 20mm height, 12mm inner diameter)
Close-up view of a shock absorber with a rubber buffer correctly installed.
Figure 3: Installed Rubber Buffer on a Shock Absorber

Operating Instructions

The rubber buffer is a passive component designed to absorb shock and reduce vibration. Once correctly installed, it operates automatically as part of your vehicle's suspension system. No specific user interaction is required for its operation.

Maintenance

To ensure the longevity and optimal performance of your rubber buffer:

  • Regularly inspect the rubber buffer for any signs of wear, cracks, or damage.
  • Keep the area around the shock absorber clean and free from dirt and debris.
  • Avoid prolonged exposure to harsh chemicals or extreme temperatures, which can degrade the rubber material.
  • Replace the buffer if significant wear or damage is observed to maintain effective shock absorption.
Close-up of the rubber buffer highlighting its high-quality rubber material and cushioning effect.
Figure 4: High-Quality Rubber Material for Good Cushioning Effect
Close-up of the inner steel pipe, emphasizing its high hardness and durability.
Figure 5: High-Quality Steel Inner Pipe for Durability

Troubleshooting

If you experience issues after installing the rubber buffer, consider the following:

  • Poor Fit: Double-check that the correct size (10mm or 12mm) was selected and that the buffer is fully seated on the shock absorber.
  • Continued Vibration/Noise: Inspect the buffer for any damage or improper installation. Ensure other suspension components are in good working order.
  • Premature Wear: Verify that the buffer is not exposed to excessive friction or harsh environmental conditions.

For persistent issues, please contact customer support.

User Tips

  • Always confirm the exact inner diameter of your shock absorber's mounting point before purchasing to ensure compatibility with either the 10mm or 12mm buffer.
  • Consider replacing both left and right side buffers simultaneously for balanced suspension performance.

Warranty and Support

For any issues, questions, or support needs regarding your product, please contact our store support. We are committed to assisting you with product-related inquiries.

You can find our contact information on the platform where you purchased the product.

© 2024 JETTING. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.