Dynoracing 52mm Dual Display Car Gauge Series

Contents

Dynoracing 52mm 7-Color LED Dual Display Car Gauge User Manual

Models: Boost, Water Temperature, Oil Temperature, Oil Pressure, Voltmeter, Air Fuel Ratio, EGT, Tachometer

1. Product Overview

The Dynoracing 52mm 7-Color LED Dual Display Car Gauge series offers a range of essential vehicle monitoring instruments. Each gauge features a 52mm diameter, a vibrant 7-color LED backlight, and a dual display (analog needle and digital readout) for clear and precise readings. These gauges are designed for front vehicle placement and are constructed from durable ABS, glass, and metal materials.

Assortment of Dynoracing 52mm gauges including Boost, Tachometer, Oil Temp, Water Temp, Oil Press, Voltmeter, Air Fuel Ratio, and EGT.
Figure 1: Various Dynoracing 52mm Dual Display Car Gauges.

2. Specifications

Feature Specification
Gauge Diameter 52mm (2 inches)
Item Height 52mm
Item Width 52mm
Item Length 52mm
Item Weight 0.4 KG
Material ABS + GLASS + METAL
Special Features Dual display (Analog + Digital), 7-Color LED Backlight
Power Supply DC 10-15V (12V only)
Current Draw (IGN ON) Max 0.3A
Current Draw (ILM ON) Max 0.3A
Placement Front (on vehicle)
Diagram showing the dimensions of the 52mm gauge: 52mm height, 52mm width, and 58mm depth.
Figure 2: Gauge Dimensions.
Product packaging showing specifications in Japanese, including power supply DC10-15V, IGN ON MAX 0.3A, and ILM ON MAX 0.3A.
Figure 3: Power Specifications from Packaging.

3. Setup and Installation

Proper installation is crucial for accurate readings and safe operation. It is recommended to have this product installed by a qualified professional if you are not familiar with automotive electrical systems.

3.1 General Wiring Instructions

All gauges in this series follow a similar basic wiring scheme. Refer to the specific diagram for your gauge type for detailed connections.

  • RED Wire: Connect to a 12V(+) ignition switched power source. This ensures the gauge turns on and off with your vehicle's ignition.
  • BLACK Wire: Connect to a reliable chassis ground or battery negative (-).
  • GREEN Wire: Typically connects to the signal wire from the corresponding sensor (e.g., temperature sensor, pressure sensor).

3.2 Specific Gauge Wiring Diagrams

Detailed wiring diagrams for various Dynoracing electrical gauges including Boost/Vacuum, Tachometer, Oil/Water Temperature, Oil Pressure, Air Fuel/Ratio, Voltmeter, and Exhaust Gas Temperature. Each diagram shows connections for Red (Ignition 12V+), Black (Battery-), and Green (Sensor/Signal).
Figure 4: Electrical Wiring Diagrams for Dynoracing Gauges.

Key connections from the diagram:

  • Boost/Vacuum Gauge (6361): Connects to a nylon tubing for pressure/vacuum.
  • Tachometer Gauge (6360): Green wire connects to the Coil or Distributor. Features a 'SET' button for backlight color and cylinder selection (1-8).
  • Oil/Water Temperature Gauge (6364/6365): Green wire connects to the temperature sensor. Ensure the sensor is properly grounded to battery negative (-).
  • Oil Pressure Gauge (6366V): Green wire connects to the pressure sensor.
  • Air Fuel/Ratio Gauge (6368): Green wire connects to the O2 Sensor Signal Wire, typically routed to the Engine Control Unit (EUC).
  • Voltmeter Gauge (6367): Red to Ignition Switch 12V(+), Black to Battery(-). No additional sensor wire.
  • Exhaust Gas Temperature (EGT) Gauge (6369): Connects to the Exhaust Gas Temp Sensor. Features additional Orange to Orange and Green to Green connections for the sensor.

3.3 Mounting

The gauges are designed for a 52mm (2 inch) mounting hole. Secure the gauge using the included mounting ring. Ensure sufficient clearance (approximately 3-5mm) behind the gauge for connecting the wiring harness.

Back view of the gauge with the mounting ring detached, showing the screw holes for securing the gauge.
Figure 5: Back of Gauge and Mounting Ring.

4. Operating Instructions

4.1 Power On/Off

The gauge will power on automatically when the vehicle's ignition is switched to the ON position, provided it is wired correctly to an ignition-switched 12V source. It will power off when the ignition is turned off.

4.2 Backlight Color Selection

Each gauge features a 7-color LED backlight. The color can be changed by pressing the small button located on the front of the gauge, usually near the bottom of the display. Repeated presses will cycle through the available colors.

A Dynoracing Boost Gauge (PSI) shown with its 7 different LED backlight colors: blue, red, green, yellow, light blue, purple, and white.
Figure 6: 7-Color LED Backlight Options.

Video 1: Demonstration of the 7-color LED backlight cycling and gauge startup sequence.

4.3 Reading the Dual Display

Each gauge provides both an analog needle sweep and a digital numerical display for the measured parameter. The analog needle offers a quick visual reference, while the digital display provides a precise value.

4.4 Tachometer Specific Settings

For the Tachometer gauge, the 'SET' button can also be used to configure the number of cylinders (1-8) to ensure accurate RPM readings for your engine type.

5. Maintenance

Dynoracing gauges are designed for durability and require minimal maintenance.

  • Cleaning: Use a soft, dry cloth to clean the gauge face and body. Avoid abrasive cleaners or solvents that could damage the display or finish.
  • Connections: Periodically check all electrical connections to ensure they are secure and free from corrosion.
  • Sensors: For gauges requiring external sensors (e.g., temperature, pressure), inspect the sensors and their connections for any signs of wear or damage. Replace faulty sensors as needed.

6. Troubleshooting

  • Gauge not powering on:
    • Check the 12V ignition power connection (RED wire) for proper voltage.
    • Verify the ground connection (BLACK wire) is secure.
    • Ensure an appropriate fuse is used in the 12V line (though specific amperage is not provided, a low-amp fuse like 1A or 2A is generally recommended for gauges).
  • Inaccurate readings:
    • Confirm the sensor is correctly installed and functioning.
    • Check the signal wire (GREEN wire) connection to the sensor and the gauge.
    • For temperature gauges, ensure the sensor is properly grounded if using an adapter that requires it.
    • For Tachometer, verify the cylinder setting is correct for your engine.
  • Backlight issues (e.g., not changing colors):
    • Ensure the gauge is receiving power.
    • Press the front button firmly to cycle through colors.
  • Gauge movement appears 'robotic':
    • This can sometimes be a characteristic of stepper motor gauges. If readings are accurate, it may be normal operation.
    • If movement is erratic or stuck, check power and signal connections.

7. User Tips

  • Brightness: The LED backlight can be extremely bright, especially at night. Consider adjusting the color to a less intense option if needed for nighttime driving.
  • External Sensors/Adapters: Some gauges, like the water temperature gauge, may require additional connectors or adapters for installation into radiator hoses. These are often sold separately.
  • Sensor Grounding: When installing external sensors, especially with adapters, ensure proper grounding of the sensor's metal casing to the chassis ground for accurate readings.
  • Cable Length: The included cable length is approximately 500mm. Plan your wiring route accordingly, and extend cables if necessary using appropriate gauge wire and connectors.
  • Rear Connector Clearance: When mounting the gauge, allow for approximately 3-5mm of clearance behind the unit for the wiring harness connector.
  • Displacement Selector: The knob on the front of the gauge typically functions as the displacement or setting selector (e.g., for changing backlight color or cylinder count on the tachometer).

8. Warranty and Support

For detailed product information, including a comprehensive user manual in PDF format, please refer to the official documentation. You can access the PDF user manual here.

If you encounter any issues not covered in this manual or require further assistance, please contact Dynoracing customer support through your purchase platform.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.