Introduction
This manual provides detailed instructions for the installation, use, and maintenance of your new non-slip fuel tank grip pads designed for the Yamaha MT-07 motorcycle (model years 2021-2023). These rubber stickers are engineered to provide enhanced grip and control, improving rider comfort and stability. Please read this manual thoroughly before installation to ensure proper application and safety.
Safety Information
This product is intended for use as a motorcycle accessory. Please observe all safety warnings and instructions during handling and installation.
EU Regulations Compliance
- This product complies with EU Regulation (EC) No 1272/2008 (CLP) on classification, labelling and packaging of substances and mixtures.
- In accordance with EU REACH Regulation (EC) No 1907/2006, this product does not contain substances of very high concern above threshold concentrations.
- Product meets requirements of Directive 2008/68/EC on the inland transport of dangerous goods.
- Manufactured in compliance with ISO 9001:2015 quality management standards.
- Disposal must comply with EU Directive 2002/96/EC (WEEE) on waste electrical and electronic equipment.
CE Marking Declaration: This product bears the CE marking indicating conformity with European health, safety, and environmental protection standards.
Hazard Statements (EU CLP)
- H225: Highly flammable liquid and vapor
- H315: Causes skin irritation
- H319: Causes serious eye irritation
- H336: May cause drowsiness or dizziness
Precautionary Statements (EU CLP)
- P101: If medical advice is needed, have product container or label at hand.
- P102: Keep out of reach of children.
- P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
- P233: Keep container tightly closed.
- P240: Ground and bond container and receiving equipment.
- P241: Use explosion-proof electrical/ventilating/lighting/.../equipment.
- P242: Use only non-sparking tools.
- P243: Take precautionary measures against static discharge.
- P280: Wear protective gloves/protective clothing/eye protection/face protection.
- P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
- P370+P378: In case of fire: Use powder, CO₂, water spray, foam for extinction.
Package Contents
The package includes the following items:
- 1x Top Fuel Tank Pad
- 2x Side Fuel Tank Grip Pads (Left and Right)
- Adhesion Promoter Packet(s)
Specifications
| Feature | Detail |
|---|---|
| Item Type | Decals & Stickers |
| Material | Rubber |
| Special Features | Waterproof, Non-slip |
| Fitment | For Yamaha MT-07 (2021, 2022, 2023 models) |
| Item Weight | 0.16 kg |
| Package Dimensions (approx.) | Length: 16 cm, Width: 22 cm, Height: 2 cm |
| Package Weight (approx.) | 0.2 kg |
Installation Guide
Follow these steps carefully for optimal adhesion and longevity of your fuel tank grip pads. This guide is also available in French and Spanish within the product documentation.
Step 1: Cleaning & Drying
- Rinse with water: Thoroughly wipe the fuel cap and surrounding area with a wet cloth. Focus on removing any oil or dust.
- Stubborn stains: For persistent marks, apply a drop of dish soap to your finger, scrub gently, then immediately rinse with clean water to prevent residue.
- Full drying: Air-dry the area naturally or wipe with a dry cloth. Ensure there is absolutely no moisture to the touch. Wait at least 10 minutes for safety to ensure complete dryness.
Step 2: Applying Adhesion Promoter (Critical Step)
- Direct application: Tear open the adhesion promoter packet. Squeeze the liquid onto your finger or a clean cloth corner.
- Even thin coat: Apply the promoter in circular motions across the entire installation area. Ensure the area covered is slightly larger than the sticker size.
- Drying standard: Wait 5 minutes until the applied promoter becomes transparent and non-sticky to a light finger touch.
Pro Tip: Less is more! Applying excess adhesion promoter can actually reduce adhesion effectiveness.
Step 3: Mounting & Sealing
- Peel backing: Remove only the top 1/3 of the backing paper from the grip pad. Align the pad precisely and fix the top edge first.
- Peel-and-press technique:
- Use your left hand to slowly peel the remaining backing paper downwards.
- Simultaneously, use the heel of your right palm to firmly press the pad onto the tank, working from the center outwards to the edges. This helps to eliminate air bubbles.
- Edge reinforcement: Once the pad is fully applied, roll-press all edges 3 times with your thumb to ensure a secure seal.
Step 4: Inspection & Curing
- Adhesion test: Press the center of each sticker firmly. If there is no lift around the edges, the adhesion is successful.
- 72-hour critical care:
- NO sun exposure: Park your motorcycle in the shade for 72 hours after installation. UV exposure and heat can lead to cracking and reduced adhesion.
- NO washing/rain: Avoid washing your motorcycle or exposing it to rain for at least 24 hours after installation to allow the adhesive to fully cure.
Operating and Use
Once properly installed, the fuel tank grip pads are designed to enhance your riding experience by providing a more secure and comfortable contact point with the motorcycle. The non-slip rubber surface helps you maintain your position during acceleration, braking, and cornering, reducing fatigue and improving control.
- Enhanced Grip: The textured surface offers superior grip for your knees and thighs, especially during aggressive riding or wet conditions.
- Improved Control: By allowing you to grip the tank more effectively, these pads help you to better control the motorcycle's movements.
- Reduced Fatigue: Less effort is required to maintain your riding position, leading to reduced fatigue on longer rides.
- Paint Protection: The pads also serve as a protective layer against scratches and wear on your fuel tank's paintwork.
Maintenance
To ensure the longevity and appearance of your fuel tank grip pads, follow these maintenance guidelines:
- Cleaning: Clean the pads with mild soap and water. Avoid harsh chemicals or abrasive cleaners that could damage the rubber material.
- Drying: After washing, dry the pads thoroughly with a soft cloth to prevent water spots or residue buildup.
- Inspection: Periodically inspect the edges of the pads for any signs of lifting or wear. Re-press any loose edges firmly to maintain adhesion.
- Avoid Extreme Conditions: While the pads are waterproof, prolonged exposure to extreme UV radiation or harsh weather conditions can affect their material over time. Parking in shade when possible is recommended.
Troubleshooting
Most issues related to fuel tank grip pads stem from improper installation. If you encounter problems, consider the following:
- Pads are lifting or peeling:
- Ensure the tank surface was thoroughly cleaned and dried before application. Any oil, dust, or moisture will prevent proper adhesion.
- Verify that the adhesion promoter was applied correctly and allowed to dry to a non-sticky state.
- Confirm that the pads were firmly pressed from the center outwards during installation, and edges were reinforced.
- Check if the 72-hour curing period was respected, avoiding sun exposure, washing, or rain.
- Air bubbles under the pads:
- Small bubbles may dissipate over time. For larger bubbles, try gently pressing them towards the nearest edge to push the air out.
- Ensure the peel-and-press technique was followed, applying pressure from the center to the edges during installation.
If issues persist after re-evaluating the installation steps, contact customer support for further assistance.
User Tips
Based on general user experiences with similar products:
- For best results, perform the installation in a warm, dry environment. This helps the adhesive cure effectively.
- Before peeling the backing, temporarily position the pads on your tank to visualize the exact placement and ensure proper alignment. Use painter's tape to mark the desired position if needed.
- Take your time during installation. Rushing can lead to misalignments or trapped air bubbles.
Warranty and Support
For any questions regarding product defects, installation challenges, or general inquiries, please refer to the official product documentation or contact the seller's customer support. A user manual in PDF format is available for download, which includes detailed safety and installation instructions in multiple languages.
Please note that improper installation or failure to follow the care instructions may void any applicable warranty.
For additional information, you may consult the User Manual (PDF).