Introduction
This manual provides detailed instructions for the proper installation and maintenance of your Yamaha MT-07 non-slip side fuel tank stickers and waterproof rubber pads. Designed to enhance grip, protect your fuel tank from scratches, and improve your riding experience, these accessories are made from robust rubber material. Please read all instructions carefully before proceeding with installation.
Safety Information
EU Regulations Compliance
- This product complies with EU Regulation (EC) No 1272/2008 (CLP) on classification, labelling and packaging of substances and mixtures.
- In accordance with EU REACH Regulation (EC) No 1907/2006, this product does not contain substances of very high concern above threshold concentrations.
- Product meets requirements of Directive 2008/68/EC on the inland transport of dangerous goods.
- Manufactured in compliance with ISO 9001:2015 quality management standards.
- Disposal must comply with EU Directive 2002/96/EC (WEEE) on waste electrical and electronic equipment.
CE Marking Declaration
This product bears the CE marking indicating conformity with European health, safety, and environmental protection standards.
Hazard Statements (EU CLP)
- H225: Highly flammable liquid and vapor
- H315: Causes skin irritation
- H319: Causes serious eye irritation
- H336: May cause drowsiness or dizziness
Precautionary Statements (EU CLP)
- P101: If medical advice is needed, have product container or label at hand
- P102: Keep out of reach of children
- P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking
- P233: Keep container tightly closed
- P240: Ground and bond container and receiving equipment
- P241: Use explosion-proof electrical/ventilating/lighting/.../equipment
- P242: Use only non-sparking tools
- P243: Take precautionary measures against static discharge
- P280: Wear protective gloves/protective clothing/eye protection/face protection
- P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
- P370+P378: In case of fire: Use powder, CO2, water spray, foam for extinction
Installation Guide
The adhesive on the side fuel tank pads must be hardened for 24 hours before the first ride.
Step 1: Cleaning & Drying
- Rinse with water: Thoroughly wipe the fuel cap and surrounding area with a wet cloth. Focus on removing any oil or dust.
- Stubborn stains: Apply a drop of dish soap to your finger, scrub gently, then immediately rinse with clean water to prevent residue.
- Full drying: Air-dry naturally or wipe with a dry cloth. Ensure there is absolutely no moisture by touch. Wait at least 10 minutes for safety to ensure complete dryness.
Step 2: Applying Adhesion Promoter (Critical Step)
- Direct application: Tear open the adhesion promoter packet. Squeeze the promoter onto your finger or a clean cloth corner.
- Even thin coat: Apply the promoter in circular motions across the entire installation area. Ensure the area covered by the promoter is slightly larger than the sticker size.
- Drying standard: Wait 5 minutes until the promoter becomes transparent and non-sticky to a light finger touch.
Pro Tip: Less is more! Excess adhesion promoter can reduce adhesion effectiveness.
Step 3: Mounting & Sealing
- Peel backing: Remove only the top 1/3 of the backing paper from the sticker. Align the sticker and fix its top edge first.
- Peel-and-press technique:
- Use your left hand to slowly peel the remaining backing paper downwards.
- Simultaneously, use your right hand to press firmly with the heel of your palm, working from the center of the sticker outwards towards the edges.
- Edge reinforcement: After applying, roll-press the edges of the sticker 3 times with your thumb to ensure a secure bond.
Operating and Benefits
These fuel tank stickers and pads are designed to provide maximum grip and control, enhancing your driving experience. The high-density rubber material improves strength and offers excellent bonding quality.
- The upper fuel tank pad prevents scratches on the fuel tank, for example, from a motorcycle jacket zipper.
- The side fuel tank pads offer optimal protection against scratches or wear marks caused by your knees.
- They contribute to a sporty appearance and provide anti-scratch protection.
Maintenance and Care
Step 4: Inspection & Curing
- Adhesion test: After installation, press the center of the sticker firmly. Zero lift indicates successful adhesion.
- 72-hour critical care:
- NO sun exposure: Park your motorcycle in the shade. UV rays and heat can cause cracking of the adhesive.
- NO washing/rain: Avoid washing the motorcycle or exposing it to rain for at least 24 hours after installation to allow the adhesive to fully cure.
For general cleaning, use a mild soap and water solution with a soft cloth. Avoid harsh chemicals or abrasive materials that could damage the rubber or adhesive.
Troubleshooting
Adhesion Issues
If the stickers do not adhere properly or the adhesive seems weak, ensure that the installation surface was thoroughly cleaned and dried as per Step 1. The adhesion promoter (Step 2) is a critical component for a strong bond. If the promoter was not applied correctly or was insufficient, it could lead to poor adhesion. Some users have reported issues with the adhesive backing; if you experience this, ensure you are using the provided adhesion promoter and following the drying times strictly.
Specifications
| Feature | Detail |
|---|---|
| Applicable Model | Yamaha MT-07 (MT07) |
| Applicable Years | 2021-2023 |
| Item Type | Decals & Stickers |
| Material | Rubber |
| Special Features | Waterproof, Anti-slip, Anti-scratch |
| Item Weight | 0.16 kg |
| Package Dimensions (approx.) | 16 cm (Length) x 22 cm (Width) x 2 cm (Height) |
| Package Weight (approx.) | 0.2 kg |
User Tips
- Check Compatibility: Always confirm that the product is compatible with your specific motorcycle model and year (e.g., Yamaha MT-07, 2021-2023). If you have an FZ25, this product is not designed for it.
- Surface Preparation is Key: Do not skip or rush the cleaning and drying steps. Any residual oil, dust, or moisture will severely compromise adhesion.
- Adhesion Promoter: The adhesion promoter is crucial. Apply it thinly and evenly, and allow it to dry to a transparent, non-sticky state before applying the pads.
- Patience with Curing: The 72-hour curing period without sun exposure or moisture is vital for the adhesive to reach its full strength.
- Size Expectations: While the overall quality is generally good, some users have noted that the middle sticker might appear smaller than anticipated. Review product images carefully to manage expectations.
Warranty and Support
For any issues or questions regarding your fuel tank stickers, please contact the seller or manufacturer directly. Refer to the product packaging or the original purchase platform for specific warranty details and contact information.
A PDF version of the item guides and documents is available for download: User Manual (PDF).