LYUNN XB2-BA/ZB/BD/BS

Contents

XB2-11BN Series Push Button Switch Instruction Manual

Model: XB2-BA/ZB/BD/BS

1. Product Overview

The XB2-11BN series push button switches are industrial-grade momentary pushbuttons designed for panel-mount control applications. They feature a chrome-plated metal bezel, 22 mm mounting hole, and screw-terminal contact blocks compatible with Normally Open (NO), Normally Closed (NC), or combined configurations.

Model Variants & Color Codes

Available models and their distinguishing features:

Model No.ColorMarkingDescription
XB2-11BN/RRedPlainStop / Emergency Stop
XB2-11BN/32Red● SymbolStop (IEC symbol)
XB2-11BN/GGreenPlainStart / Run
XB2-11BN/31Green✓ SymbolStart (IEC symbol)
XB2-11BN/BLBlackPlainGeneral purpose
XB2-11BN/35Black↓ ArrowDown / Lower
XB2-11BN/34White↓ ArrowDown / Lower
XB2-11BN/WWhitePlainGeneral purpose
XB2-11BN/YYellowPlainCaution / Reset
XB2-11BN/BBluePlainGeneral purpose
XB2-11BN/36Blue↑ ArrowsUp / Down
Various XB2-11BN series push button switches in different colors and markings.
Figure 1: XB2-11BN Series Push Button Switches

2. Setup & Installation

  1. Step 1: Drill Mounting Hole
    Drill a 22 mm diameter hole in the control panel where the switch will be mounted.
  2. Step 2: Insert Button Body
    Insert the button body from the front of the panel into the drilled hole.
  3. Step 3: Secure with Locking Nut
    Thread the locking nut onto the rear thread of the switch and tighten it firmly to secure the switch to the panel.
  4. Step 4: Attach Contact Block
    Attach the desired contact block (NO, NC, or combined) to the rear of the actuator.
  5. Step 5: Connect Wiring
    Proceed to connect the wiring as described in the 'Wiring Instructions' section.
  6. Step 6: Verify Operation
    Before applying full power, verify that the switch operates correctly.

Note: Panel thickness of 1-6 mm is recommended. The mounting torque for the locking nut should be approximately 1.2-1.5 N·m.

Diagram showing dimensions of a push button switch: 28mm head diameter, 54mm total height, 22mm mounting hole, screw fixing.
Figure 2: Push Button Switch Dimensions and Mounting

3. Wiring Instructions

3.1 1NO 1NC Wiring (Single Normally Open + Single Normally Closed)

  • Terminal 1 & 2: NC contact (normally closed)
  • Terminal 3 & 4: NO contact (normally open)

Connect the FireWire (Live / L) to terminal 1 (NC) or 3 (NO). Connect the load to terminal 2 or 4. The Zero line (Neutral / N) connects to the load's neutral terminal.

3.2 2NO / 2NC Wiring (Two Normally Open / Two Normally Closed)

  • Upper Block (Terminals 3 & 4): First circuit
  • Lower Block (Terminals 3 & 4): Second circuit

Both circuits share the same switching action.

IMPORTANT: Always de-energize the circuit before wiring. Do not exceed the rated voltage and current. Overtightening terminals may damage the contact block.

Wiring diagram for single NO/NC and two NO/NC contacts.
Figure 3: Wiring Diagrams for Push Button Switches
Table showing contact types (1NO 1NC, 2NO, 2NC) with their default state/schematic and push status/schematic.
Figure 4: Contact Block Types and Schematics

4. Operating Instructions

The XB2-11BN series push button switches are momentary devices, meaning they return to their default state when the button is released. The operation depends on the contact block configuration:

4.1 1NO + 1NC (Single Normally Open + Single Normally Closed)

  • Default State: The green (NO) circuit is open; the red (NC) circuit is closed.
  • Pushed State: The green (NO) circuit closes; the red (NC) circuit opens.

4.2 2NO (Two Normally Open)

  • Default State: Both circuits (green) are open.
  • Pushed State: Both circuits close simultaneously.

4.3 2NC (Two Normally Closed)

  • Default State: Both circuits (red) are closed.
  • Pushed State: Both circuits open simultaneously.

5. Maintenance & Safety Precautions

  • Do not use in explosive atmospheres or corrosive environments.
  • Do not exceed the rated electrical parameters (voltage and current).
  • This product is not a safety-rated emergency stop device unless certified separately.
  • Maintenance and replacement must be performed by qualified personnel.
  • Disconnect power before cleaning; use a dry cloth only.
  • Regularly inspect for contact wear, loose terminals, or mechanical damage.

6. Specifications

6.1 Technical Specifications

ParameterValueNote
Rated VoltageAC 240V / DC 24V-
Rated Current3A (AC15)IEC 60947-5-1
Conventional Thermal Current (Ith)10A-
Insulation Voltage (Ui)415V-
Impulse Withstand Voltage (Uimp)6kV-
Mounting Hole22 mmScrew fixing
Contact Block StandardGB/T 14048.5ZB2-BE101C
Actuator ActionMomentary (spring return)-
Protection ClassIP40 (front panel)-
MaterialAlloy-
Contact Resistance≤50mΩ-
Electrical Insulation Resistance≥100mΩ-

6.2 Dimensions

DimensionValueNote
Button head diameter28 mmOverall width
Total height (with contact block)54 mm-
Mounting hole22 mmPanel cutout
Mounting methodScrew fixingPanel thickness 1-6 mm
Diagram showing dimensions of a rotary switch: 28.7mm head width, 68.5mm total height, 29mm base width, 30mm base depth, 22mm mounting hole.
Figure 5: Rotary Switch Dimensions (for reference)

7. User Tips

  • Users have found these switches to be exactly as advertised, offering excellent value for money.
  • The product generally meets expectations, indicating reliable performance.

8. Warranty & Support

This product is warranted against manufacturing defects for 12 months from the date of purchase under normal use conditions. The warranty does not cover damage caused by misuse, improper installation, or exceeding rated parameters.

9. Compliance & Standards

  • IEC 60947-5-1: Low-voltage switchgear and controlgear — Control circuit devices
  • GB/T 14048.5: Low-voltage switchgear and controlgear (Chinese national standard)
  • CCC: China Compulsory Certification mark on contact block

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.