1. Introduction
The SinoTrack J14 Car GPS Tracker is a compact and reliable device designed for real-time vehicle tracking. It supports 2G communication and utilizes GPS, Beidou, and LBS for accurate positioning. This manual provides detailed instructions for setting up, operating, and maintaining your J14 GPS tracker to ensure optimal performance and security for your vehicle.
Key Features:
- Real-time GPS Tracking
- Geo-fence Creation
- Driver Behavior Monitoring
- Live Alert Notifications
- Analysis Reports
- Daily Route Maps
- Remote Fuel/Electricity Cut-off (requires relay connection)
- Built-in 150mAh Battery
- GT06 Protocol Support
- Free Tracking Platform and Mobile App
2. Package Contents
Please check the package for the following items:
- SinoTrack J14 GPS Tracker Unit
- Power Wiring Harness with Inline Fuse
- User Manual (this document, also available as PDF: View PDF)
3. Setup and Installation
3.1. SIM Card Insertion
- Open the tracker's casing carefully to access the SIM card slot.
- Insert a 2G-compatible (medium-sized) SIM card into the slot. Ensure the SIM card has an active data plan and sufficient balance for SMS commands.
- Close the casing securely.
3.2. Wiring Diagram and Connection
The J14 tracker requires a 9-90V DC power supply. Connect the wiring harness as follows:
- Red Wire: Connect to the positive (+) terminal of the vehicle's power supply (e.g., car battery or ACC power).
- Black Wire: Connect to the negative (-) terminal of the vehicle's power supply (ground).
- Yellow Wire: (Optional) Connect to ACC (Accessory) power for ignition detection.
- Orange Wire: (Optional) For remote fuel/electricity cut-off. Connect to a relay (not included) as per the relay's instructions.
Important: Ensure correct polarity to prevent damage to the device and vehicle electronics. The inline fuse provides protection; do not bypass it.
3.3. Initial Power-Up
Once connected, the device will power on automatically. Observe the LED indicators:
- Blue LED (GPS): Solid blue indicates GPS signal acquired. Flashing blue indicates searching for GPS signal.
- Green LED (GSM): Solid green indicates GSM network connected. Flashing green indicates searching for GSM network.
Allow a few minutes for the device to acquire GPS signal and connect to the GSM network, especially during the first use or after a long period of inactivity.
4. Operation
4.1. Tracking Platform and Mobile App
The SinoTrack J14 tracker can be monitored via a free online tracking platform and a dedicated mobile application. These platforms allow you to view real-time location, historical routes, set geo-fences, and receive various alerts.
- Download the official SinoTrack mobile app from your device's app store or access the web platform.
- Register an account and add your device using its IMEI number (usually found on the device itself or its packaging).
- Follow the on-screen instructions within the app/platform for real-time tracking and feature configuration.
4.2. SMS Commands
The tracker can also be controlled and configured using SMS commands sent from a registered phone number to the SIM card number in the device. Below are some common commands. For a comprehensive list, please refer to the full PDF manual.
| Parameter Description | Set Command | Query Command | Illustration/Description |
|---|---|---|---|
| Version query | CXZT | CXCS#SOFTVERSION | Can only query, not set or send CXZT |
| Server address | SZCS#SERVIP=IP,PORT | CXCS#SERVIP#SERVPORT | Example: SZCS#SERVIP=122.9.115.220#SERVPORT=7711 |
| Activation location reporting interval | SZCS#FREQ=30 | CXCS#FREQ | Unit is seconds, limit value is greater than 5. Example: SZCS#FREQ=30 (report every 30 seconds) |
| Sleep time | SZCS#SLEEPT=3 | CXCS#SLEEPT | Unit is minutes, define the waiting time to enter sleep mode without vibration and ACC off. Default is 3 minutes. |
| Overspeed alarm | SZCS#SPEED=120 | CXCS#SPEED | Alarm when speed exceeds 120 km/h. |
| APN settings | SZCS#APN=APNNAME#USER#PW | CXCS#APN#USERPPP#PWPPP | Example: SZCS#APN=cmnet#666#123 (APN: cmnet, User: 666, Pass: 123). If no user/pass, use SZCS#APN=APNNAME. |
| Fuel cut-off method | SZCS#SOURCE_OFF_TYPE=0 | CXCS#SOURCE_OFF_TYPE | 0 = disconnection when speed is below 20 km/h. 1 = immediate disconnection. (Requires relay) |
| SOS number 1 setting | SZCS#SOS_CODE2=NUMBER | CXCS#SOS_CODE2 | Set mobile phone number for SOS alerts. Example: SZCS#SOS_CODE2=13580000001 |
Note: Replace placeholders like IP, PORT, APNNAME, USER, PW, NUMBER with your specific information. Ensure the sending phone number is registered as an administrator if required by the device's configuration.
5. Specifications
| Feature | Specification |
|---|---|
| Dimensions (L x W x H) | 70mm x 13mm x 10mm |
| Weight | 25.9g |
| Built-in Battery | 150mAh (3.7V) |
| GPS Sensitivity | -162dbm |
| GSM Band | 850/900/1800/1900MHZ (2G) |
| Working Temperature | -20°C to +60°C |
| Communication System | 2G |
| Positioning Accuracy | 3-30m |
| Positioning Mode | GPS+Beidou+LBS |
| Working Voltage | 9-90V |
| Locating Time | <30sec (outdoor) |
| Storage Temperature | -20°C to +70°C |
| Antennas | Built-in GPS and GSM antennas |
6. Maintenance
- Keep the device dry. Moisture can damage internal circuits.
- Avoid extreme temperatures.
- Do not drop or subject the device to strong impacts.
- Clean the device with a dry cloth. Do not use chemicals or detergents.
- Ensure the wiring connections are secure and free from corrosion.
7. Troubleshooting
7.1. Device Not Powering On
- Check the power connections (red wire to positive, black wire to negative).
- Verify the vehicle's battery voltage is within the 9-90V range.
- Inspect the inline fuse in the power harness. Replace if blown.
7.2. No GPS Signal (Blue LED Flashing)
- Ensure the device is installed in an open area with a clear view of the sky.
- Avoid installing the device under metal objects or inside enclosed spaces that can block GPS signals.
- Allow sufficient time (up to several minutes) for initial GPS acquisition.
7.3. No GSM Network (Green LED Flashing)
- Check if the SIM card is correctly inserted and activated.
- Ensure the SIM card has an active 2G data plan and sufficient balance.
- Verify network coverage in the device's location.
- Try restarting the device by disconnecting and reconnecting power.
7.4. Inaccurate Tracking or No Data on Platform
- Confirm APN settings are correct via SMS command (refer to Section 4.2).
- Ensure the device has both GPS and GSM signals (solid blue and green LEDs).
- Check the server address configuration if you are using a custom server.
8. User Tips
- Not Waterproof: The J14 tracker is not waterproof. Install it in a location protected from moisture and direct water exposure.
- SIM Card Size: This device requires a medium-sized SIM card. Ensure you have the correct size before insertion.
- Value for Money: Users often find this tracker to be a good value for its features and reliability for simple tracking needs.
- Integrated Fuse: The integrated fuse in the wiring harness is a safety feature. Do not remove or bypass it.
9. Frequently Asked Questions (FAQ)
Q: What app or platform does the SinoTrack J14 use for tracking?
A: The SinoTrack J14 uses the official SinoTrack tracking platform and a dedicated mobile application. You can usually find the app by searching for "SinoTrack Pro" or similar in your app store, or by visiting the official SinoTrack website for platform access details.
10. Warranty and Support
For warranty information, technical support, or further assistance, please contact your retailer or the official SinoTrack customer service. Keep your purchase receipt as proof of purchase.