FMS FCX24M

Contents

FMS FCX24M 1/24 RC Land Rover Series Off-Road Vehicle Instruction Manual

Models: Defender D90, Defender D110, Discovery, Range Rover

Model Number: FCX24M

1. Introduction

Thank you for choosing the FMS FCX24M 1/24 RC Land Rover Series Off-Road Vehicle. This product is a highly detailed, remote-controlled model designed for enthusiasts aged 14 and above. It offers a realistic and enjoyable off-road experience, whether indoors or outdoors. This manual provides essential information for the correct operation, maintenance, and repair of your vehicle.

The FMS FCX24M series faithfully reproduces the iconic Land Rover models, including the Range Rover, Defender 90, Defender 110, and Discovery, at a 1/24 scale. Each model features hard plastic car shells for accurate detail, detachable components for customization, and roof racks for optional scale accessories. The chassis is designed with a non-bearing trapezoidal metal beam and solid front and rear axles, providing excellent ground clearance and climbing capabilities. It also includes a two-speed transmission and a powerful 050 motor, powered by a 380mAh 2S LiPo battery for approximately 30 minutes of high-speed driving.

Video: FMS FCX24M Land Rover Series RC Car in action, showcasing off-road capabilities and different models.

2. Safety Precautions and Warnings

This product is not a toy! Recommended for ages 14 and up. Adult supervision is required for users under 14 years old. Contains small parts, keep out of reach of children 3 years of age and younger.

General Safety Guidelines

  • Always turn on the transmitter before connecting the battery to the model. When turning off the model, always disconnect the battery first, and then turn off the transmitter. Failure to follow this order may result in loss of control and serious damage.
  • Never allow transmitter batteries to run low, as this can cause loss of vehicle control.
  • Plastics on the vehicle are susceptible to damage or deformation due to extreme heat and cold. Store the model indoors, in a climate-controlled, room temperature environment, away from heat sources like ovens or heaters.
  • Replace damaged components with original factory parts. Pay special attention to the polarity of all vehicle wiring.
  • Use common sense when selecting the environment to operate your vehicle. Do not operate near power cables, cellular/radio towers, deep water, or unstable terrain. The operator is solely responsible for their actions.
  • The product is composed of precision electrical components. Keep it away from moisture and other contaminants.
  • Always check the radio range of the vehicle prior to operation to prevent radio loss or interference.
  • Operate this product within your ability. If retrieving the vehicle is dangerous, it is not worth the risk.
  • Do not use the product at night or in bad weather (rain, thunderstorm) as it can cause erratic operation or loss of control.
  • Do not use the product when visibility is limited.
  • Do not use the product on rainy or snowy days. Any exposure to moisture (water or snow) may cause erratic operation or loss of control.
  • Do not touch any part of the model that may generate heat during operation or immediately after use (engine, motor, speed control) as they may be very hot and cause serious burns.

Safety Symbols

Pay close attention to the following symbols and their meanings. Failure to follow these warnings could cause damage, injury, or death.

  • ⚠ Danger: Not following these instructions may lead to serious injuries or death.
  • ⚠ Warning: Not following these instructions may lead to major injuries.
  • ⚠ Caution: Not following these instructions may lead to minor injuries.
  • ⛔ Prohibited: Do not use the product at night or in bad weather like rain or thunderstorm. Do not use the product when visibility is limited. Do not use the product on rain or snow days. Any exposure to moisture (water or snow) may cause erratic operation or loss of control.

3. Product Overview and Features

The FMS FCX24M series brings the legacy of Land Rover's Camel Trophy vehicles to a 1/24 scale RC model. These models are designed for both aesthetic appeal and robust off-road performance.

Key Features:

  • Scale Realism: Hard plastic car shells faithfully reproduce details of Range Rover, Defender 90, Defender 110, and Discovery models.
  • Customization: Detachable components like bumpers, fender flares, rearview mirrors, and door handles allow for custom paint schemes.
  • Functional Accessories: Each model comes with its own roof rack, optionally equipped with scale parts like fuel drums, spare tires, equipment boxes, and recovery boards.
  • Lighting System: Front and rear lights, as well as roof-mounted searchlights, have designated lamp positions, with headlights pre-installed.
  • Robust Chassis: Features a non-bearing trapezoidal metal beam with solid front and rear axles.
  • Advanced Drivetrain: Utilizes a two-speed transmission and a powerful Brushed 050 motor (35T) for ample torque and speed.
  • Backpropagation Structure: The reverse transmission output structure of the gearbox effectively reduces shaft effects and provides a more simulated climbing posture.
  • Adjustable Suspension: Equipped with adjustable suspension points.
  • High-Performance Tires: Large-diameter tires provide sufficient ground clearance and climbing capabilities.
  • Power Source: Powered by a 380mAh 2S LiPo battery, offering approximately 30 minutes of high-speed driving.
Underside view of the FCX24M chassis, showing the backpropagation structure and drivetrain.

Image: Underside view of the FCX24M chassis, showing the backpropagation structure and drivetrain. The reverse transmission output structure of the gearbox effectively reduces shaft effects and provides a more simulated climbing posture.

4. Specifications

General Specifications:

  • Brand Name: FMS
  • Model Number: FCX24M
  • Scale: 1:24
  • Type: Car (Remote Control, Features)
  • Design: Cars
  • Material: Metal, Plastic, ABS
  • Power: Brushed 050 motor 35T
  • State of Assembly: Ready-to-Go
  • Flight Time (Operating Duration): 30min
  • Remote Distance: 30m
  • Control Channels: 3 channels
  • Controller Mode: MODE2
  • Charging Voltage: 7.4V
  • Remote Control: Yes
  • Is Batteries Included: Yes (for car)
  • Remote Battery: 4*AAA battery (not included)
  • Recommend Age: 14+y
  • Certification: CE
  • Origin: Mainland China
  • Package Includes: Original Box, Batteries, Operating Instructions, Remote Controller, USB Cable
  • High-concerned chemical: None
  • Is Electric: Lithium Battery

Model-Specific Dimensions and Clearances:

Table of FCX24M Series product specifications for Range Rover, Guard D110, Discover, and Guard D90 models.

Image: Table of FCX24M Series product specifications for Range Rover, Guard D110, Discover, and Guard D90 models, including color, shell material, motor type, tire size, wheelbase, highest ground clearance, and product size (LWH).

FCX24M Series Specifications
Product Name Color Shell Material Motor Type Tire Size (D x W) Wheelbase Highest Ground Clearance Product Size (L x W x H)
Range Rover first generation Yellow ABS Brushed 050 motor 35T D:48mm W:17mm 134mm 28mm 227*103*120mm
Guard D110 Yellow ABS Brushed 050 motor 35T D:50mm W:20mm 135mm 29mm 240*107*128mm
Discover the first generation Yellow ABS Brushed 050 motor 35T D:48mm W:17mm 134mm 28mm 232*105*133mm
Guard D90 Yellow ABS Brushed 050 motor 35T D:50mm W:20mm 111mm 24mm 214*107*128mm

Transmitter (FMS-G3) Specifications:

  • Product Model: FMS-G3
  • Compatible Receivers: FMS-R3A
  • Compatible Models: 1:18, 1:24 simulation cars or climbing cars
  • Number of Channels: 3
  • RF: 2.4GHz ISM
  • Maximum Power: <20dBm (e.i.r.p.) (EU)
  • 2.4G Protocol: AFHDS 2A-BS
  • Distance: >100m (Ground distance without interference)
  • Resolution: 1024
  • Input Power: 6V DC or 1.5AAA*4
  • Working Current: 10mA (Static); 120mA/6V (Dynamic)
  • Charging Port: No
  • Low Voltage Alarm: < 4.2V
  • Antenna: Built-in single antenna
  • Data Port: No
  • Temperature Range: -10°C ~ +60°C
  • Humidity Range: 20%~95%
  • Online Update: No
  • Color: Blue
  • Dimensions: 115.2*75.5*145mm
  • Weight: About 113g
  • Certification: CE, FCC ID: 2A2UNG300

Receiver (FMS-R3A) Specifications:

  • Product Model: FMS-R3A
  • Compatible Transmitters: FMS-G3
  • Compatible Models: 1:18/1:24 simulation cars or climbing cars
  • Applicable Motors: 050 motor set
  • PWM Channels: 2
  • Number of Lights: 1
  • RF: 2.4GHz ISM
  • 2.4GHz Protocol: AFHDS 2A-BS
  • Input Power: 2S LiPo battery
  • Continuous / Peak Current: 10A/40A
  • BEC Output: 5V/1A
  • Maximum Power: <20dBm (e.i.r.p.) (EU)
  • Distance: >100m (Ground distance without interference)
  • Antenna: External antenna
  • Data Output: PWM
  • Resolution: 1024
  • Temperature Range: -10°C ~ +60°C
  • Humidity Range: 20%~95%
  • Online Update: No
  • Dimensions: 32*24.4*12mm
  • Weight: 8g
  • WaterProof: PPX4
  • Certification: CE, FCC ID: 2A2UNR3A00

5. Setup

5.1. Transmitter Battery Installation

The transmitter has a built-in antenna and operates automatically once powered on.

  1. Open the battery compartment cover.
  2. Insert 4 AAA batteries with the correct polarity. Ensure the metal terminals connect properly.
  3. Replace the battery compartment cover.

Warning: Only use specified batteries (4x AAA batteries). Do not open, disassemble, or attempt to repair the battery. Do not crush/puncture the battery or short the external contacts. Do not expose to excessive heat or liquids. Do not drop the battery or expose it to strong shocks or vibrations. Always store the battery in a cool, dry place. Do not use the battery if damaged.

Low Battery Alarm: When the battery voltage is lower than 4.2V, the transmitter will emit an alarm and the LED will flash slowly.

5.2. Receiver and Servo Installation

Ensure the receiver is mounted in an appropriate location within the model for a stable signal.

  • Make sure the receiver is not installed near ESCs or other sources of electrical noise.
  • Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal to ensure normal function. Do not pull the antenna or tie it with servo cables.
  • All servo interfaces and the car light interface use 1.25 mm standard pins. The motor interface is a PH2.0 female interface.
Diagram of the receiver with numbered labels for interfaces like motor, battery, power switch, antenna, LED, and channels.

Image: Diagram of the receiver with numbered labels for interfaces like motor, battery, power switch, antenna, LED, and channels.

5.3. Connecting the Vehicle Battery

  1. Release the hook and loop fastener to separate the shell body from the chassis from the front end.
  2. Load the battery into the battery compartment.
  3. Connect the battery plug (51005 2P Male) to the female connector of the receiver/ESC combo unit.
  4. Close the engine hood.

Battery Compartment Size: 53*21*17mm

Diagram showing how to connect the battery to the FCX24M RC car, with the shell body separated from the chassis.

Image: Diagram showing how to connect the battery to the FCX24M RC car, with the shell body separated from the chassis.

5.4. Spare Tire Installation

Install the spare tire using the included hex screw and spacer as shown in the diagram.

Diagram showing the installation of the spare tire on the rear of the RC car.

Image: Diagram showing the installation of the spare tire on the rear of the RC car.

6. Operating Instructions

6.1. Transmitter Overview

The FMS-G3 transmitter uses a 2.4GHz AFHDS 2A-BS Automatic Frequency Hopping Digital System, supporting two-way transmission and 3 channels.

Diagram of the transmitter (remote control) with numbered labels for various buttons and controls.

Image: Diagram of the transmitter (remote control) with numbered labels for various buttons and controls.

  1. Steering Wheel CH1
  2. Throttle Trigger CH2
  3. Three-position Switch CH3
  4. Lanyard Eye
  5. Handle (4x AAA batteries can be installed inside)
  6. LED Indicator
  7. BIND Button (Binding, turn on or off the car light or reset data)
  8. ST- Button (Decrease CH1 trim and travel value)
  9. TH- Button (Decrease CH2 trim and travel value)
  10. Power Switch
  11. REV Button (Reverse CH1 or CH2)
  12. ST+ Button (Increase CH1 trim and travel value)
  13. TH+ Button (Increase CH2 trim and travel value)

6.2. Power-on Procedure

Caution: For safety, always power on the transmitter before the receiver.

  1. Check that the batteries are fully charged and installed correctly in the transmitter.
  2. Toggle the Power Switch to the [ON] position. The transmitter's LED will be solid on.
  3. Connect the receiver to power (vehicle battery).

Transmitter LED Status:

  • Off: Transmitter is not powered on.
  • Slow flashing: Low voltage alarm.
  • Fast flashing: Transmitter is in bind mode.
  • Gradual: Transmitter is in Sleep mode or Idle alarm state.
  • Three-flash-one-off: Transmitter is in standby state, while the bound receiver is powered off, unbound, or no signal.

6.3. Binding (Pairing)

The transmitter and receiver are pre-bound at the factory. If you need to replace the receiver or bind additional receivers, follow these steps:

  1. Turn on the transmitter while holding the BIND button. The transmitter will enter bind mode, and its LED will flash quickly. Release the BIND button.
  2. Power on the receiver. It will wait for 1 second and then automatically enter binding state if no connection is found.
  3. The receiver's LED will turn solid on, indicating successful binding.
  4. Check that the transmitter and receiver functions are working correctly. If problems arise, repeat steps 1-3.

Note: If binding is not completed within ten seconds, the receiver's LED will enter its slow flashing state.

6.4. Car Light Control

When the receiver and transmitter are normally connected, short press the BIND button on the transmitter to turn the car lights on or off. By default, the car lights are off.

6.5. Drag Brake Function

This function allows you to set the drag brake percentage (default: 0%).

  1. Under normal power-on, quickly press the REV button twice within 1 second to enter the drag brake setting mode. The green LED will flash.
  2. Select the desired drag brake setting value by pressing the corresponding button:
    • ST-: 0%
    • ST+: 50%
    • TH-: 75%
    • TH+: 100%
  3. Press the BIND button to cycle through with and without brake.
  4. Quickly press the REV button twice within 1 second to exit the setting mode.

6.6. Trims and Travel of Gear Shift Servo

This function adjusts the trim and travel for the gear shift servo (CH3).

  1. Under normal power-on, quickly press the BIND button twice within 1 second to enter the mode. The green LED will flash.
  2. Adjust to the appropriate state using the following buttons:
    • ST-/+: Increases/decreases adjustment step (trim)
    • TH-/+: Increases/decreases servo travel
  3. Quickly press the BIND button twice within 1 second to exit.

6.7. Channel Reverse

This function reverses the output direction of a channel.

  • CH1 (Steering): When the steering wheel is at maximum or minimum travel, press the REV button to reverse CH1. Each press switches the direction.
  • CH2 (Throttle): When the throttle trigger is at maximum or minimum travel, and the steering wheel is in the neutral position, press the REV button to reverse CH2. Each press switches the direction.

Warning: Pay special attention when reversing the throttle channel, as the model car will move at full speed if the trigger is at full throttle position.

6.8. Trim Setting

This function adjusts the neutral position (trim value) of the channels.

  • CH1 (Steering): When the steering wheel is in the neutral position, press the ST+/- button to adjust CH1 trim.
  • CH2 (Throttle): When the throttle trigger is in the neutral position, press the TH+/- button to adjust CH2 trim.

ST+/TH+: Increase trim value. ST-/TH-: Decrease trim value. Trim range: -150 us to +150 us (step: 5 us, default: 0). The buzzer will sound for prompts. Holding the button changes the value continuously. Two beeps indicate passing the neutral position, and a long beep indicates reaching the endpoint.

6.9. D/R Setting (Dual Rate)

This function adjusts the travel range value of the channels.

  • CH1 (Steering): When the steering wheel is at maximum or minimum travel, press the ST+/- button to adjust CH1 travel value.
  • CH2 (Throttle): When the throttle trigger is at maximum or minimum travel, press the TH+/- button to adjust CH2 travel value.

ST+/TH+: Increase travel value. ST-/TH-: Decrease travel value. Travel range: 0-120% (default: 100%, step: 5%). The buzzer will sound for prompts. Holding the button changes the value continuously. A long beep indicates reaching the endpoint.

7. Maintenance

7.1. Battery Precautions (Vehicle LiPo Battery)

  • Only use a charger designed for LiPo batteries. Never charge with chargers for Nicd, NIMH, or other battery types.
  • Do not leave the LiPo battery unattended during charging.
  • Do not overcharge the battery.
  • Always charge LiPo batteries on non-flammable, heat-resistant surfaces.
  • Always use a LiPo-safe bag or container while charging. Do not allow LiPo cells to overheat (above 60°C/140°F), as this can cause damage or fire.
  • Do not charge the LiPo pack while it is still in the model. Never charge or store battery packs in a vehicle.
  • Do not discharge LiPo excessively, as this will damage the battery.
  • Do not expose LiPo cells to water or moisture.
  • Do not store the battery near open flame or heaters.
  • Do not assemble LiPo cells or pre-assembled packs with other LiPo cells or packs.
  • Always store the LiPo battery in a secure location away from children.
  • Always remove the LiPo battery if the model is involved in any kind of crash.
  • Carefully inspect the battery and connectors for even the smallest damage.
  • Cells may become hot after usage. Allow the pack to cool to room temperature prior to recharging.
  • Do not allow electrolyte to get into eyes or on skin. Wash affected areas immediately if contact occurs.
  • Do not alter or modify connectors or wires of a LiPo battery pack.
  • Always inspect the condition of the battery before charging and operating.
  • Do not short circuit the LiPo battery.
  • Do not have direct contact with a leaky/damaged battery.
  • Do not charge the battery outside the recommended temperature range (0°C-45°C).

8. Troubleshooting

8.1. System Functions

  • Failsafe Setting: The failsafe function protects the model and personnel if the receiver loses signal. CH2 will enter brake mode. By default, the receiver outputs the last channel value. To set failsafe, press and hold the BIND button for 3 seconds while the transmitter is in normal working state. The current channel value is set as the failsafe value. The buzzer will sound long upon success. Note: Failsafe settings revert to default if the transmitter is re-bound.
  • Reset Data: To reset transmitter function data, press and hold the BIND button and REV button while powering on the transmitter. The buzzer will sound long. Note: Failsafe settings, binding information, and stick calibration are not reset.
  • Idle Alarm: If the transmitter has no operation for over 10 minutes, it enters idle alarm state. The LED will show a gradual light, and the buzzer will sound twice quickly in a cycle. Any control input will cancel the alarm.
  • Sleep Mode: If the transmitter remains in idle alarm state for over 2 minutes, it enters sleep mode. The LED will show a gradual light, the buzzer is off, and RF is off. The transmitter enters a low power consumption state and will not respond to controls. To exit, power off and restart the transmitter.
  • Low Voltage Alarm: If the transmitter voltage is below 4.2V, it enters low voltage alarm state. The LED will flash slowly, and the buzzer will sound. For safety, if battery voltage drops below 3.5V, the wireless system will stop working.
  • Offline Prompt: If the transmitter detects that the bound receiver has turned off or disconnected for over 2 seconds, the transmitter LED will show three-flash-one-off. This state exits when the transmitter re-establishes communication with the receiver.

8.2. Receiver Protection Functions

  • Low Voltage Protection: If the receiver battery voltage drops below 6.4V, all channels will have no output.
  • Overheating Protection: If the receiver temperature is too high, the CH2 motor channel will have no output, while the CH1 channel maintains normal output. Normal output for CH2 resumes once the temperature returns to normal.

8.3. Common Issues & Solutions (Based on User Feedback)

  • Wheels do not turn, motor works: This indicates a potential issue with the drivetrain connection between the motor and the wheels. Check the gears, axles, and universal drive shafts for any disconnections or damage. Ensure all components are properly seated and secured.
  • Car steers but does not move forward/backward: This suggests a problem with the throttle channel (CH2) or its connection to the motor. Verify the throttle trigger is functioning correctly. Check the binding process and ensure the throttle channel is not reversed. Inspect the motor and ESC connections.
  • Difficulty with battery connections for charging: Some users find the battery connections difficult for children. Consider leaving the charging cable connected under the chassis and securing the USB connection on the roof rack with an elastic band for easier access.

9. User Tips

  • Improve Crawler Performance: To enhance the crawling capabilities, consider adding weight to the wheels. This can improve traction and stability on challenging terrains.
  • Indoor Fun: The 1/24 scale makes these RC cars perfect for indoor entertainment. Create obstacle courses using household items like books, keyboards, and mobile phones.
  • Outdoor Adventures: While great indoors, these vehicles truly shine on natural outdoor terrains. Explore rocky paths, muddy trails, and small inclines.
  • Enjoy with Others: Many users find these cars so enjoyable that they consider buying multiple units to play with friends or family.

10. Parts List

For a detailed list of all spare parts, please refer to the original PDF manual pages 22-25. This includes components for the Range Rover, Defender 90, Defender 110, and Discovery models, covering wheel assemblies, oil shock absorbers, axles, gearboxes, motors, servos, and various body parts.

11. Certifications

DoC Declaration

Hereby, FMS declares that the Radio Equipment [FMS-G3 & FMS-R3A] is in compliance with RED 2014/53/EU.

CE Warning

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

FCC Statement (Appendix 1)

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Caution: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

Environmentally Friendly Disposal

Old electrical appliances must not be disposed of together with residual waste but must be disposed of separately. Disposal at communal collecting points is free. Owners are responsible for bringing appliances to these points to contribute to recycling valuable raw materials and proper treatment of toxic substances.

CE Mark: CE Mark

FCC ID: 2A2UNR3A00

12. Warranty and Support

For the most up-to-date product manual, supplementary instructions, and warnings, please visit the official FMS website: www.fmshobby.com.

This manual is intended to assist you in correctly operating, maintaining, and repairing the vehicle. Since most of the components involved in this product are unique parts, please keep this manual for future reference.

For further details, including the full user manual in PDF format, please refer to the official document: User manual (PDF).

13. Disclaimer

FMS and its distributors are not liable for any losses caused by users not following the product manual. In compliance with laws and regulations, FMS reserves the final interpretation of this manual and the right to update, revise, or terminate these terms without prior notice.

© 2024 FMS. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.