OPUYYM CX6 Series

Contents

OPUYYM CX6 Series 18650 Power Bank Case Instruction Manual

DIY Battery Storage Box with Fast Charging and Flashlight

Introduction

Thank you for choosing the OPUYYM CX6 Series 18650 Power Bank Case. This DIY power bank case allows you to assemble your own portable charging solution using 18650 lithium batteries (not included). It features multiple input and output ports, an LCD digital display for real-time battery capacity monitoring, and a built-in flashlight. Depending on the model, it may also include Power Delivery (PD) fast charging and Qi wireless charging capabilities.

This manual provides detailed instructions for the safe and efficient use of your power bank case. Please read it carefully before assembly and operation.

Product Overview

Video: Product overview and assembly demonstration.

Front and internal view of the power bank case

Image: Front view of the power bank case with digital display and internal view showing the circuit board and battery slots.

Power bank case with screws for repeatable opening

Image: Exploded view showing the power bank case and its screws, highlighting the repeatable opening design.

Setup and Battery Installation

This power bank case is designed to hold six 18650 flat head lithium batteries. Batteries are NOT included.

Important Battery Requirements:

  • Only use 18650 flat head batteries. Pointed batteries cannot be used as they may not fit or make proper contact.
  • Ensure the battery's outer skin is intact and not damaged. Damaged batteries can be a safety hazard.
  • The battery voltage should be between 3.2V-4.2V.
  • All battery cells must be the same type and capacity; do not mix different batteries.

Installation Steps:

  1. Test Batteries: Before installation, test each 18650 battery to ensure it is normal and usable.
  2. Identify Polarity: Distinguish between the positive (+) and negative (-) poles of your batteries. The positive pole is typically marked with a "+" and often has a slightly raised or flat surface. The negative pole is marked with a "-" and is usually flat.
  3. Diagram distinguishing positive and negative battery terminals

    Image: Diagram illustrating how to distinguish between the positive and negative terminals of 18650 batteries.

  4. Open the Case: Carefully remove the screws to open the power bank case.
  5. Insert Batteries Correctly: Insert each battery into its designated slot. Align the positive pole of the battery with the protruding point surface (spring contact) of the shrapnel inside the case. Install the negative pole of the battery to the coil surface of the shrapnel.
  6. Correct battery installation diagram

    Image: Visual guide for correct battery installation, showing the proper orientation of positive and negative terminals with the internal contacts.

    Important considerations for battery installation

    Image: Diagram highlighting critical points for battery installation: use flat head batteries, ensure no skin damage, and press firmly to the spring side.

  7. Avoid Reverse Installation: Reverse installation will burn the circuit board.
  8. Close the Lid: After installing all batteries in sequence, test the normal charge and discharge functions. Then, carefully close the lid and secure it with the screws.

Initial Activation (CX6-PD-QI Version Only):

For the CX6-PD-QI version, after installing the batteries, the display may show "o" or 0%. At this time, it will not output directly. You must first input power to the battery box (charge the power bank) to activate it. The display will then show normally.

Activation steps for CX6-PD-QI version

Image: Illustration of the activation process for the CX6-PD-QI model, showing initial 'o' display and subsequent normal display after charging.

Operating Instructions

Power Button and Display:

  • Power Button: Located on the side/top of the device.
  • ON/OFF: Long press the power button to turn the power bank ON or OFF.
  • LED Lights (Flashlight): Long press the power button to activate or deactivate the built-in LED flashlight.
  • Power Display: The LCD digital display shows the real-time battery capacity percentage.
Diagram of the power bank's ports and power button for CX6+Flashlight model

Image: Diagram showing the power button, power display, Micro Input, Lightning Input, Type C Input, and Output ports for the CX6+Flashlight model.

Diagram of the power bank's ports and power button for CX6-PD model

Image: Diagram showing the power button, power display, Micro Input, Lightning Input, Type C Input & Output (PD charge), and Fast Charge Output ports for the CX6-PD model.

Diagram of the power bank's ports and power button for CX6-PD-QI model

Image: Diagram showing the power button, power display, Micro Input, Lightning Input, Type C Input & Output (PD charge), Fast Charge Output ports, and Wireless Charging Area for the CX6-PD-QI model.

Charging External Devices:

  • Connect your device to one of the available USB output ports (USB-A, Type-C) using a compatible charging cable.
  • For models with wireless charging (CX6-PD-QI), place your Qi-compatible device on the wireless charging area. Ensure proper alignment for efficient charging.
  • The power bank supports fast charging for compatible devices, depending on the model.

Charging the Power Bank:

  • Connect the power bank to a power source using one of the input ports (Micro USB, Lightning, or Type-C).
  • The LCD display will show the charging status and battery percentage.
  • The power bank itself supports fast charging input for quicker recharging.

Maintenance

  • Keep the power bank case clean and dry. Avoid exposure to moisture or extreme temperatures.
  • Do not use or store the power bank in a high-temperature environment.
  • Regularly inspect your 18650 batteries for any signs of damage to their outer skin. Replace damaged batteries immediately.
  • When not in use for extended periods, store the power bank with a partial charge (around 50%) to prolong battery life.

Troubleshooting

Problem Possible Cause Solution
Power bank does not turn on/charge devices. Batteries incorrectly installed, damaged batteries, or PD-QI version not activated. Check battery polarity and ensure they are flat head and undamaged. For PD-QI models, connect the power bank to a charger to activate it.
Wireless charging is not working or phone falls off. Phone not Qi-compatible, improper alignment, or case interference. Ensure your device supports Qi wireless charging. Realign the phone on the charging pad. Remove thick phone cases if necessary.
Inaccurate charge percentage display. Using batteries with capacities significantly different from standard 2600mAh or 3000mAh. This is a known limitation with some high-capacity batteries. The power bank will still function, but the display may not be perfectly accurate.
Screws are difficult to tighten or protrude. Over-tightening or misalignment during assembly. Tighten screws carefully with a bit of force to ensure they are flush with the case. Avoid excessive force.
Device does not fast charge at 12V. Device incompatibility or specific fast charging protocol not supported for output. While the power bank may charge itself at 12V, some devices may only support fast charging at 9V. Check your device's charging specifications.

Specifications

This power bank case can accommodate 6 x 18650 flat head lithium batteries.

Feature CX6+Flashlight CX6-PD+Flashlight CX6-PD-QI+Flashlight
Output/Input Power 5V-2.1A Output: 5V-3A, 9V-2A, 12V-1.5A
Input: 5V-3A, 9V-2A, 12V-1.5A
Output: 5V-3A, 9V-2A, 12V-1.5A, 4.5V-5A, 5V-4.5A
Input: 5V-3A, 9V-2A, 12V-1.5A
Wireless Charging Output N/A N/A 5W/7.5W/10W/15W (Max)
Battery Type 6 x 18650 Flat Head Lithium Batteries (not included)
Protection Features Temperature protection, Short circuit protection, Reset protection, Over current protection, Over voltage protection, Battery overshoot protection.
Package Dimensions (approx.) Length: 9 cm, Width: 6 cm, Height: 9 cm
Weight (approx.) 0.125 kg (without batteries)

Note: Specifications are subject to change without prior notice.

User Tips

  • For maximum capacity and longer usage, consider using high-capacity 18650 batteries (e.g., 3000mAh or 3500mAh).
  • Be aware that the power bank does not feature individual battery balancing. This means some batteries might experience more load than others over time.
  • When assembling, ensure all screws are tightened carefully and firmly to prevent them from protruding or getting caught.
  • The built-in flashlight is quite bright and can be useful in emergency situations.
  • If you plan to use the power bank as an emergency power source for devices like a router, ensure it has a trigger function or appropriate voltage output.

Frequently Asked Questions (FAQ)

Q: Does this power bank case have a Battery Management System (BMS)?
A: While the product description lists several protection features (temperature, short circuit, over current, over voltage, battery overshoot protection), it does not explicitly state a full BMS for individual cell balancing. It is important to use matched batteries of the same type and capacity.
Q: Is the wireless charging magnetic?
A: The product features Qi wireless charging. While some Qi chargers have magnetic alignment, it is not explicitly stated for this model. Ensure your device is properly aligned on the wireless charging area for optimal performance.
Q: Is the wireless charging compatible with iPhone?
A: Yes, if your iPhone model supports Qi wireless charging, it should be compatible with the CX6-PD-QI version's wireless charging feature.

Warranty and Support

For any issues, questions, or support regarding your OPUYYM CX6 Series Power Bank Case, please contact the seller or retailer from whom you purchased the product. They will be able to provide assistance with troubleshooting or warranty claims as per their policies.

For additional information or to view the original user manual in PDF format, you may refer to the following link: User manual (PDF)

© 2023 OPUYYM. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.