1. Introduction
Thank you for choosing the AZDOME M200 Dash Cam. This manual provides essential information for the proper operation, installation, and maintenance of your device. Please read it thoroughly before use to ensure optimal performance and safety. For any further assistance, please contact our customer support.
Note: The contents of this manual are subject to change without prior notice to improve product performance.
2. Important Safety Information
To prevent damage to the product or injury to yourself and others, please observe the following safety precautions:
- Do not disassemble, repair, or modify the product yourself. This may cause fire, electric shock, or malfunction. Contact customer service for internal inspection or repair.
- If any foreign matter enters the product, immediately detach the power cord and contact customer service.
- Do not adjust the product while driving. Always stop or park your car in a safe place before making adjustments.
- Do not install the product in a location that obstructs the driver's field of vision.
- Do not use damaged or modified power cords. Only use cords provided by the manufacturer to prevent explosion, fire, or malfunction.
- Do not operate the product with wet hands to avoid electric shock.
- Avoid installing the product in environments with high humidity, combustible gases, or liquids, which could cause an explosion or fire.
- Keep the product away from infants, children, and pets to prevent them from swallowing small components or causing a short circuit from saliva.
- Do not spray water or wax directly onto the product during car cleaning.
- If smoke or an unusual smell is emitted from the power cord, detach it immediately and contact customer service or your distributor.
- Keep power cord terminals clean to prevent excessive heat and fire.
- Use the correct input voltage to avoid explosion, fire, or malfunction.
- Plug the power cord firmly to prevent accidental disconnection and potential fire.
- Do not cover the product with any material. Ensure the product and peripherals are in a well-ventilated location to prevent external deformation or fire.
3. Package Contents
Before installation, please verify that all items are present in the box:
- Dash camera ×1
- Electrostatic films ×2
- Type-C car charger with 3.5m/12ft cable ×1
- Cable clips ×5
- Pry tool ×1
- User manual ×1

4. Product Diagram
Familiarize yourself with the components of your AZDOME M200 Dash Cam:
| # | Description |
|---|---|
| 1 | Sticker mount |
| 2 | Lens |
| 3 | Micro-SD card slot |
| 4 | Mini USB charging port |
| 5 | Power button (Short press: Lock video; Long press (3s): Shut down; Long press (10s): Restore default settings and restart) |
| 6 | Speaker |
| 7 | Blue indicator light |
| 8 | Microphone |
| 9 | Reset button |
5. Setup
5.1 Initial Setup & Power Management
The camera is designed to power up and record automatically when it receives power, then save the video record and turn off automatically when the car shuts off.
Auto Power ON/OFF:
- Plug the car charger into the cigarette lighter socket.
- When the car engine is on, the dash cam will turn ON and start recording automatically.
- When the car key is turned to the LOCK position, the dash cam automatically saves the recording and turns OFF.
Manual Power ON/OFF:
- Manually Turn ON: Press the power button once.
- Manually Turn OFF: Press and hold the power button for at least 2 seconds.
Important Notes:
1. A U3 type microSD card (Not included) is required. Format your microSD card with the dash cam for the first time use.
2. ALWAYS connect with power when using. The built-in 1mAh Lithium Metal Battery is only used to memorize time.
3. The dash cam automatically updates its time when connected to the AZDOME APP via WiFi.
4. If your car's 12V cigarette outlet is always HOT (provides constant power even when the car is off), the auto ON/OFF feature will not work. To prevent battery drain, hardwire your dash cam to your car's fuse box with a 3-Lead Auto Trigger Hardwire Kit, or change the connection in the fuse box for your 12V outlet to a socket that only supplies power when the car key is in ACC or ON position.
5.2 Installation Guide
Install the front camera behind the rearview mirror. Ensure the windshield is clean and dry before installation.
- Turn off the engine. Gently push the microSD card into the slot until it locks into place. (Use a Class 10 or above high-speed U3 micro-SD card).
- Find a suitable place on the windshield that does not obstruct the driver's field of vision. Clean and dry the area. Tear off the protective layer of the electrostatic sticker and adhere it to the windshield to prevent marks/glue.
- Peel off the protective film from the double-sided tape and attach the front camera to the electrostatic sticker. Adjust the lens angle by rotating the camera body.
- Plug the cigarette lighter power cable into the cigarette lighter socket and the front camera. Use the pry tool to lift the edges of the windshield trim/molding and tuck in the power cord.
- Turn on the engine. The dashcam will power up and start recording. Video files are stored on the microSD card. When you turn off the engine, the dashcam will automatically stop recording and power down.

6. Operating Instructions
6.1 Smartphone App & Video Management
The AZDOME M200 features built-in WiFi for high-speed data transmission, allowing you to download and share footage easily via the smartphone app.

- Download the App: Search for the 'AZDOME' app in the Google Play Store or Apple App Store and install it on your smartphone.
- Connect to WiFi: Go to your phone's Settings > WiFi > Select the WiFi network of the dash cam (e.g., M200_XXXXXX). The default password is '12345678'. It may say 'No Internet Connection', which is normal as the dash cam WiFi is only for video/photo transfer.
- Check Real-time Video: Once connected, the app will show the dash cam model M200. Press 'Check Real-time Video' to view the live video preview.
- Download Video Files: To download files, first STOP recording in the app. Then, press the 'Device Album' button to access Photo, Video, and Emergency files. Select the desired video files and press the download icon.
Troubleshooting App Live Video:
- For Android phones: When connecting to the dash cam's WiFi, your phone might show a pop-up or notification about 'No Internet'. Tap on this notification and select 'YES' or 'Keep' to stay connected to the WiFi network.
- For iPhone: If the app doesn't show live video, disable the 'AZDOME' cellular data for the app in your phone's settings. Ensure 'Local Network' for 'AZDOME' is turned on. For latest iOS, go to Settings > AZDOME > 'Wireless Data' > Select 'WLAN'. For older iOS, go to Settings > AZDOME > Disable 'Cellular Data'.
6.2 Viewing Video Files on Computer
- Remove the microSD card from the dashcam.
- Insert the card into a microSD card reader and connect it to your computer.
- Locate the added flash drive (e.g., D:, E:). Double-click to access file folders: Normal (loop recording), Event (locked emergency files), and Photo (captured photos).
- To play videos, simply double-click them. We recommend using VLC Media Player (available at www.videolan.org).
6.3 General Settings
Access general settings through the AZDOME app. After connecting via WiFi and stopping recording, press the settings icon in the app to adjust various parameters:
- Video Resolution: 1920x1080P 30fps.
- Loop Recording: Select video clip length (1/3/5 minutes). When the memory card is full, the oldest files are automatically deleted.
- Audio Recording: Turn On (Default) / Off. The dashcam has a built-in microphone.
- G-Sensor: Off / Low / Medium (Default) / High. Detects impacts and locks the current video file as an emergency file, preventing it from being overwritten.
- Video Stamps: Turn On/Off AZDOME LOGO/Date/Time Stamp on recorded files.
- Frequency: 50HZ / 60HZ (Default). Choose based on your geographical location.
- Boot Ringtone: On (Default) / Off.
- Volume: Off / Low (Default) / MID / High. Sets the volume level for boot sound and prompts.
- Date/Time Format: Select the desired date format.
6.4 Parking Mode
This function requires a 3-Lead Mini USB Hardwire Kit (not included, search JYX02 Mini 3-Lead Hardwire Kit for M200 Dash Cam on Amazon) to be installed properly. It offers two modes:
- Time-Lapse Parking Mode: When the engine is off, the camera automatically enters 1fps time-lapse recording. If an impact is detected (G-Sensor triggered), it records a 1-minute continuous video, saves it to the Event folder, and then returns to time-lapse recording. It automatically stops when the car starts.
- Collision Detection Parking Mode: When the engine is off, the camera enters impact detection mode and turns off. If an impact is detected (G-Sensor triggered), the camera turns ON, records a 1-minute continuous video, saves it to the Event folder, and then turns OFF again. It automatically returns to normal video mode when the car starts.
6.5 System Settings
- Synchronization Time: Syncs the dash cam's time with your phone via the app.
- WiFi: Allows changing the WiFi Name and Password in the app.
- Default Settings: Resets the Dash Cam to default settings. Your recordings will not be affected.
7. Maintenance
7.1 SD Card Maintenance
The dash cam supports up to 128GB Micro SD Class 10, U3 Speed cards. For stable performance, it is recommended to format the memory card every 1-2 months.
Formatting the Micro-SD Card:
- Via Dash Cam: Press and hold the WiFi button for more than 8 seconds to restore factory settings and format the memory card. A success message will appear.
- Via App: Connect to the dash cam's WiFi via the AZDOME APP. Go to the settings button in the upper right corner of the real-time preview page to find the formatting menu.
7.2 Firmware Update
Keeping your dash cam's firmware updated ensures optimal performance and access to new features.
- Remove the microSD card from the dashcam and connect it to a computer using a card reader.
- Download the latest M200 Firmware from www.azdomes.com > Support > Downloads.
- Unzip the downloaded firmware (Zip file) and copy the firmware file (e.g., "******.bin") to the root directory of the microSD card.
- Connect the camera to the car charger to start the firmware update process. You will see an upgrade progress bar.
- The firmware update may take up to 1 minute. Do not disconnect power during the update. The camera will turn OFF automatically once updated.
- You can verify the latest firmware version in the APP's settings > Firmware Version.
8. Troubleshooting (FAQ)
- Q1: Camera turns ON / OFF automatically?
- Ensure the output current can reach 5V/1A and use the provided car charger. If your car's cigarette outlet is always hot, refer to the 'Initial Setup & Power Management' section for solutions.
- Q2: Video Image is blurred?
- Remove the protective lens film, clean the lens, and ensure the windshield is clean and clear of grease, dirt, and debris. The Dash Cam has a minimum focal range of around 2 meters; objects closer than this may appear blurred.
- Q3: Camera gets HOT?
- It is normal for the camera to run slightly hot due to high-speed video recording. The dash cam may be hot during use, but should not exceed 158°F/70°C.
- Q4: Video Files cannot be played on my computer?
- The video files are in MOV/MP4 format. Ensure you have suitable playback software installed on your PC (e.g., VLC Media Player).
- Q5: Video has no sound?
- Ensure that the 'Audio Recording' setting is turned ON in the dash cam's settings.
- Q6: Why isn't there a picture of the back of the camera?
- The AZDOME M200 is a single-channel dash cam designed for front-facing recording only. It does not include a rear camera or internal recording capabilities.
- Q7: Can I remove the camera from the bracket?
- Yes, the camera can be detached from its sticker mount for storage or transfer.
9. User Tips
- SD Card Choice: Always use a U3 type microSD card for reliable recording performance.
- Regular Formatting: To maintain optimal performance and prevent recording issues, format your microSD card every 1-2 months.
- Consistent Power: Ensure the dash cam is always connected to a stable power source while in use, as its internal battery is primarily for time memory.
- App Connectivity: If experiencing issues with the smartphone app, ensure you've followed the specific steps for Android or iOS to maintain WiFi connection, especially regarding 'No Internet' prompts or cellular data settings.
- Lens Clarity: Regularly check and clean the dash cam's lens and your windshield to ensure clear video quality.
10. Technical Specifications
| Feature | Specification |
|---|---|
| Model | M200 |
| Aperture | F=2.0 |
| Color | Black |
| OSD Language | English, French, German, Italian, Japanese, Russian, Spanish |
| Memory Card Required Reading Speed | Class 10, U3 Speed |
| Max External Memory | 128GB (Not included) |
| Video Code | H.264 |
| Video Format | MOV |
| Photo Format | JPG |
| Video Resolution | 1920x1080P 30fps |
| WiFi | Built-in |
| Built-in Screen | No |
| Battery | Built-in 1mAh Lithium Metal Battery (for time memory) |
| Power Interface | 5V/1A |
| Operation Temperature | -20°C to 70°C (-4°F to 158°F) |
| View Angle | 170° |
| Camera Resolution | 1920x1080 |
| Pixels | 200Mega |
| Special Features | G-Sensor, SD/MMC Card, Built-in GPS, Anti Vibration, WiFi Function, Parking Monitor, NightShot Function, Loop-Cycle Recording |
| Number Of Lenses | 1 |
| Imaging Sensor | GC2053 |
| Assembly Mode | Hidden Type |
| Chipset Manufacturer | MSTAR |
| Frames Per Second | 30 |
| Item Type | Car DVR |
| Certification | CE, FCC, RoHS, WEEE |
| Interface | SD/MMC, USB 2.0 |



11. Warranty & Support
11.1 Customer Service
For any inquiries, issues, or support needs, please contact our customer service team:
- Email: service@azdome.hk (Response in just 12 hours)
- WhatsApp: Scan the QR code on the manual cover using the WhatsApp camera to add us.
Contact us before returning any item. We are committed to helping you resolve any issue as soon as possible.
11.2 Product Warranty
The AZDOME M200 Dash Cam comes with a One-Year Limited Warranty.
11.3 User Manual (PDF)
A detailed user manual (PDF) is available for download from the manufacturer's website. You can find it at https://manuals.plus/m/aac7cfa3cb037d750a92a28daaa9fed15df87c9c69249e5c3b4c422d6f3f2f0e.
12. Regulatory Notices
12.1 CE Compliance
This product complies with the radio interface requirements of the European Community.
12.2 RoHS Compliance
This symbol indicates that the product must not be discarded as household waste. It should be delivered to an appropriate collection point for recycling to protect natural resources, human health, and the environment. For more information on disposal and recycling, contact your local municipality, disposal service, or the shop where you purchased the product.
12.3 FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC ID: 2A297-LS01D