JGINYUE X99-8D4/2.5G

Contents

JGINYUE X99-8D4/2.5G Dual CPU Motherboard User Manual

Model: X99-8D4/2.5G

1. Introduction

The JGINYUE X99-8D4/2.5G is a high-performance dual CPU motherboard designed for demanding computing tasks, including gaming, office applications, workstations, and servers. It supports Intel LGA 2011-3 Xeon E5 V3 and V4 series processors, offering robust memory support with eight DDR4 slots and advanced connectivity options including dual 2.5G network cards and multiple M.2 NVMe interfaces. This manual provides essential information for the proper installation, operation, and maintenance of your motherboard.

2. Safety Information

Please read and follow these safety guidelines carefully to prevent damage to the motherboard and ensure personal safety:

  • Always disconnect the power supply from the wall outlet before installing or removing any components.
  • Wear an anti-static wrist strap or frequently touch a grounded object (e.g., the metal chassis) to discharge static electricity before handling the motherboard or other components.
  • Handle the motherboard by its edges to avoid touching sensitive components.
  • Ensure proper ventilation within your computer case to prevent overheating.
  • Keep the motherboard away from moisture, dust, and extreme temperatures.
  • Do not attempt to repair the motherboard yourself. Contact qualified service personnel for assistance.

3. Package Contents

Upon opening your JGINYUE X99-8D4/2.5G motherboard package, please verify that all items are present and in good condition. The standard package typically includes:

  • JGINYUE X99-8D4/2.5G Motherboard
  • SATA Cables
  • I/O Shield
  • User Manual (this document)
JGINYUE X99-8D4/2.5G Motherboard in retail packaging
Figure 3.1: JGINYUE X99-8D4/2.5G Motherboard in its retail box.

4. Product Overview

The JGINYUE X99-8D4/2.5G motherboard is an E-ATX form factor board designed for dual Intel LGA 2011-3 processors. It features a robust power delivery system and extensive connectivity for high-performance computing.

JGINYUE X99-8D4/2.5G Dual Circuit Board Overview
Figure 4.1: JGINYUE X99-8D4/2.5G Dual Circuit Board Overview with key features.
JGINYUE X99-8D4/2.5G Motherboard Interface Diagram
Figure 4.2: JGINYUE X99-8D4/2.5G Motherboard Interface Diagram.

Key features and interfaces include:

  • CPU Sockets: Dual LGA 2011-3 sockets supporting Intel Xeon E5 V3 and V4 series processors.
  • Memory: 8 DDR4 memory slots, supporting up to 256GB in a two-set, four-channel configuration (2133/2400/2666MHz).
  • Storage: 10 SATA 3.0 ports and 2 M.2 NVMe interfaces for high-speed storage.
  • Network: Dual Intel 2.5G network card interfaces for high-bandwidth connectivity.
  • Expansion Slots: 3 PCI Express x16 slots and 2 PCI Express x1 slots.
  • USB Ports: A combination of USB 3.0 and USB 2.0 ports on the rear I/O and internal headers.
  • Power Delivery: 8+8 phase power supply (24+24 MOS) for stable power to CPUs.
  • Diagnostics: Onboard digital display for diagnostic codes, buzzer, power button, and restart button.
  • Cooling: Multiple fan headers (2x 4-pin, 2x 3-pin).

5. Specifications

Detailed technical specifications for the JGINYUE X99-8D4/2.5G Motherboard:

JGINYUE X99-8D4/2.5G Motherboard Detailed Parameters
Figure 5.1: JGINYUE X99-8D4/2.5G Motherboard Detailed Parameters.
JGINYUE X99-8D4/2.5G Motherboard Specifications
Feature Specification
ModelX99-8D4/2.5G
CPU SocketLGA 2011-3 (Supports Intel Xeon E5 V3/V4 Series)
ChipsetIntel X99 (Original Chipset)
Memory Slots8 x DDR4 (Quad Channel per CPU)
Memory Frequency2133/2400/2666MHz
Maximum RAM Capacity256GB
Power Supply Interface24-Pin + 8-Pin + 8-Pin
Power Delivery8+8 Phase (16-phase total)
Network Card (NIC)Dual Intel 2.5G Network Card
SATA Interface10 x SATA 3.0
M.2 Interface2 x M.2 NVMe Protocol
PCIe Slots3 x PCI Express x16, 2 x PCI Express x1
USB Interface (Rear)4 x USB 3.0, 4 x USB 2.0
USB Interface (Front Headers)1 x USB 3.0, 2 x USB 2.0
Fan Interface2 x 4-Pin, 2 x 3-Pin
PS/2 Interface1 x PS/2 Keyboard, 1 x PS/2 Mouse
Other InterfacesOnboard buzzer, power button, restart button, digital display diagnosis
Form FactorE-ATX (330mm x 300mm)
PCB Thickness10-layer PCB
JGINYUE X99-8D4/2.5G Motherboard Ten Upgraded Designs
Figure 5.2: Highlights of the motherboard's design features.

6. Setup Instructions

Follow these steps to properly install your JGINYUE X99-8D4/2.5G motherboard and its components:

6.1. Motherboard Installation

  1. Ensure your computer case supports the E-ATX form factor (330mm x 300mm).
  2. Install the I/O shield into the rear opening of your computer case.
  3. Carefully align the motherboard with the standoffs in your case and gently place it down.
  4. Secure the motherboard with screws, ensuring not to overtighten.

6.2. CPU Installation (Dual Sockets)

This motherboard supports two LGA 2011-3 CPUs. The process is identical for both sockets.

  1. Locate the two CPU sockets (LGA 2011-3) on the motherboard.
  2. Open the CPU socket retention levers.
  3. Carefully place the Intel Xeon E5 V3 or V4 processor into the socket, aligning the golden triangle on the CPU with the indicator on the socket. Ensure the CPU is seated correctly without force.
  4. Close the retention levers to secure the CPU.
  5. Apply thermal paste to the CPU(s) and install compatible CPU cooler(s).

6.3. Memory (RAM) Installation

The motherboard has 8 DDR4 memory slots, supporting quad-channel memory per CPU. For optimal performance, populate memory in matched pairs or quads, following the motherboard's manual for specific slot population order.

  1. Open the clips at both ends of the DDR4 memory slot.
  2. Align the notch on the memory module with the key in the slot.
  3. Press down firmly on both ends of the memory module until the clips snap into place.

6.4. Storage Device Installation

M.2 NVMe SSDs:

  1. Locate the two M.2 NVMe slots.
  2. Insert the M.2 SSD into the slot at an angle.
  3. Gently push down the SSD and secure it with the provided screw.

SATA Drives:

  1. Connect one end of a SATA data cable to a SATA 3.0 port on the motherboard.
  2. Connect the other end of the SATA data cable to your HDD/SSD.
  3. Connect a SATA power cable from your power supply to the HDD/SSD.

6.5. Expansion Card Installation (PCIe)

  1. Remove the corresponding slot cover from your computer case.
  2. Align your PCI Express x16 (e.g., graphics card) or x1 card with the slot.
  3. Press down firmly until the card is fully seated.
  4. Secure the card to the case with a screw.

6.6. Power Supply Connections

  1. Connect the 24-pin ATX power connector from your power supply to the main power header on the motherboard.
  2. Connect the two 8-pin CPU power connectors (EPS12V) from your power supply to the corresponding headers near the CPU sockets.

6.7. Front Panel and Fan Connections

  1. Connect the front panel headers (Power SW, Reset SW, HDD LED, Power LED) to the designated pins on the motherboard (refer to Figure 4.2 for locations).
  2. Connect your case fans and CPU cooler fans to the available 4-pin or 3-pin fan headers.
  3. Connect front panel USB and audio cables to their respective headers.

7. Operating Instructions

7.1. Initial Boot-Up

  1. After all components are installed and connected, ensure all power cables are securely plugged in.
  2. Turn on your power supply.
  3. Press the power button on your computer case or the onboard power button on the motherboard.
  4. The system should power on, and you should see a display on your monitor.

7.2. BIOS/UEFI Access

To enter the BIOS/UEFI setup utility, press the DEL key or F2 key repeatedly during the initial boot-up sequence. The BIOS allows you to configure system settings, boot order, fan speeds, and other advanced options.

7.3. Operating System Installation

Once in the BIOS, configure the boot order to prioritize your USB drive or optical drive containing the operating system installation media. Save changes and exit the BIOS to begin the OS installation process.

8. Maintenance

  • Dust Removal: Regularly clean dust from inside your computer case, especially from CPU coolers, fan blades, and heatsinks, using compressed air. Dust accumulation can lead to overheating.
  • Cable Management: Ensure cables are neatly routed to allow for optimal airflow within the case.
  • BIOS Updates: Periodically check the manufacturer's website for BIOS updates. BIOS updates can improve system stability, add support for new hardware, or fix bugs. Exercise caution when updating the BIOS; follow instructions precisely to avoid system damage.
  • Component Checks: Occasionally check all connections (power, data, expansion cards) to ensure they are secure.

9. Troubleshooting

This section addresses common issues you might encounter with your motherboard.

9.1. Digital Diagnostic Display

The motherboard features an onboard digital display that shows POST (Power-On Self-Test) codes. These codes can help identify the source of a problem if the system fails to boot or display video. Refer to the motherboard's specific POST code list (often found in a more detailed technical manual or online) to interpret these codes.

9.2. Common Issues and Solutions

  • No Power/No POST:
    • Check all power connections (24-pin, 8-pin CPU, GPU).
    • Ensure the power supply is switched on.
    • Reseat CPU(s) and RAM modules.
    • Try booting with only one CPU and one RAM stick to isolate the issue.
    • Check the digital diagnostic display for error codes.
  • No Display:
    • Ensure your monitor is connected to the graphics card (if installed) and not the motherboard's non-existent integrated graphics output.
    • Reseat the graphics card.
    • Test with a different graphics card if possible.
    • Check monitor input selection.
  • System Instability/Crashes:
    • Check CPU and GPU temperatures.
    • Ensure RAM is properly seated and compatible.
    • Run memory diagnostic tools.
    • Update BIOS to the latest version.
    • Check for driver updates for all components.
  • CPU Compatibility (V3/V4 Xeon):
    • The motherboard is designed to support both Intel Xeon E5 V3 and V4 processors. If you encounter issues with a V4 CPU, ensure your BIOS is updated to the latest version, as early BIOS revisions might have limited V4 support.
    • Verify that your specific CPU model is listed as compatible by the manufacturer.

10. User Tips

  • BIOS Updates for V4 CPUs: If you plan to use an Intel Xeon E5 V4 processor, it is highly recommended to update the motherboard's BIOS to the latest available version. Some users have reported that V4 CPU support might require a BIOS update, even if the product description states V3/V4 compatibility.
  • Memory Configuration: For optimal performance, especially with dual CPUs, ensure your DDR4 memory modules are installed in a balanced quad-channel configuration for each CPU. Refer to the motherboard's silkscreen or a more detailed manual for the recommended slot population order.
  • Power Supply: Given the dual CPU configuration and potential for multiple GPUs, ensure your power supply unit (PSU) has sufficient wattage and the necessary 24-pin and dual 8-pin CPU power connectors.

11. Frequently Asked Questions (FAQ)

Q: Does this motherboard support Intel Xeon E5 V4 processors?
A: Yes, the JGINYUE X99-8D4/2.5G motherboard is designed to support both Intel Xeon E5 V3 and V4 series processors. However, for optimal compatibility and stability with V4 CPUs, it is strongly recommended to update the BIOS to the latest version available from the manufacturer.
Q: What does it mean if the BIOS description mentions limited V3/V4 support?
A: If you encounter conflicting information regarding V3/V4 support, it typically means that while the hardware is capable, certain CPU models, especially V4, might require a specific BIOS version to function correctly or optimally. Always ensure your BIOS is up-to-date.
Q: Can I install an E5-2699 V4 or E5-2667 V4 CPU?
A: The motherboard supports Xeon E5 V4 series CPUs. For specific models like the E5-2699 V4 or E5-2667 V4, ensure your BIOS is updated to the latest version to guarantee full compatibility and performance.

12. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your proof of purchase for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.