LYUNN WD16-22D1

Contents

LYUNN WD16/19/22D1 Series Metal Button Switch User Manual

Model: WD16-22D1

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your LYUNN WD16/19/22D1 Series Metal Button Switch. Please read this manual thoroughly before use to ensure safe and efficient operation.

Two waterproof metal button switches with water droplets, a yellow 'STOP' ring in the background.
Figure 1: WD16/19/22D1 Series Metal Button Switches, highlighting their waterproof design.

2. Safety Information

Always observe the following safety precautions to prevent injury or damage to the product:

  • Ensure power is disconnected before installation or maintenance.
  • Verify that the voltage and current ratings of the switch match your application requirements.
  • Improper wiring can lead to malfunction or electrical hazards. Consult a qualified electrician if unsure.
  • Do not exceed the rated current of 20A/250VAC.

3. Product Features

  • Durable Construction: Shell made of aluminum oxide black anodized material, offering resistance to corrosion and high mechanical life.
  • High Protection Rating: IP-rated protection against water, dust, and corrosion.
  • Integrated LED: Built-in micro-chip LED with a step-down resistor for stable illumination, eliminating the need for external current-limiting resistors.
  • Wide Voltage Compatibility: Supports a broad voltage range including 3-6V, 12-24V, 36-48V, and 110-220V.
  • Multiple Luminous Colors: Available in red, green, blue, yellow, and white LED colors.
  • Versatile Operation: Selectable self-momentary (resetting) or self-locking operation modes.
  • High Current Capacity: Designed to withstand up to 20A high current.
Close-up of silver contacts inside a button switch with electrical arcs, indicating high current capacity.
Figure 2: Increased and thickened silver contacts allow the switch to handle up to 20A high current.

4. Technical Specifications

ParameterValue
Model SeriesWD16D1 / WD19D1 / WD22D1
Diameter (Mounting Hole)16mm / 19mm / 22mm
Shell MaterialAluminum oxide, black anodized
Rated Current20A / 250VAC
LED TypeMicro-chip LED with built-in step-down resistor
LED VoltageWide: 3-6V / 12-24V / 36-48V / 110-220V
LED ColorsRed / Green / Blue / Yellow / White
Contact Type1NO (normally open)
Protection RatingWater / Dust / Corrosion / Temperature resistant (IP67)
WarrantyOne year
Technical drawing showing detailed dimensions for 16mm, 19mm, and 22mm button switches, including pin and screw foot versions.
Figure 3: Detailed dimensions for 16mm, 19mm, and 22mm switch variants.
Side view of a button switch being measured with calipers, showing a torsion length of 2.4CM.
Figure 4: The compact design features a torsion length of only 2.4CM.

5. Installation

5.1. Mounting

  1. Prepare Mounting Hole: Cut a mounting hole with a diameter matching your switch size: Ø16 mm, Ø19 mm, or Ø22mm. Refer to the product model for the correct size.
  2. Panel Thickness: Ensure the panel thickness is within the specified range for secure installation.
  3. Secure Switch: Insert the switch into the mounting hole and firmly tighten the lock nut to ensure IP-rated sealing.

5.2. Wiring

Connect the wiring correctly by referring to the terminal markings on the switch. Ensure the selected LED voltage version matches your power supply.

Close-up of a switch's silver-plated pin, showing 'WANDW 20A/250VAC' and 'NO' markings, indicating better conductivity and longer lifespan.
Figure 5: 4.8MM Silver plated pin for better conductivity and longer lifespan. Corresponding foot letters are easier to read.

Wiring Mode 1: Keep Button Light On

This mode keeps the button light continuously illuminated.

Wiring diagram for a button switch where the light remains on. It shows a power source connected to the switch and a device, with the light connected in parallel to the power source.
Figure 6: Wiring diagram for constant button light. Press to power on, press again to power off.

Wiring Mode 2: Synchronous Button Light

This mode illuminates the button light synchronously with the device operation.

Wiring diagram for a button switch where the light operates synchronously with the device. It shows the power source, switch, and device, with the light connected to illuminate when the device is active.
Figure 7: Wiring diagram for synchronous button light. Press to power on, press again to power off.

6. Operating Modes

6.1. Self-Momentary (Self-Resetting) Operation

In this mode, the switch acts as a momentary contact. The circuit is connected only while the button is pressed. Upon releasing the button, it returns to its original position, and the circuit is disconnected.

  • Action: Press down to connect.
  • Result: Release button to reset (spring-return), disconnecting the circuit.

6.2. Self-Locking Operation

In this mode, the switch maintains its state after being pressed. The circuit remains connected until the button is pressed again.

  • Action: Press once to connect.
  • Result: Press again to disconnect (maintains locked state until next press).

7. Maintenance

The LYUNN Metal Button Switch is designed for high mechanical life and durability. Regular maintenance is generally not required under normal operating conditions. For cleaning, use a soft, dry cloth. Avoid using harsh chemicals or abrasive materials that could damage the switch's finish or internal components.

8. Troubleshooting

If you encounter issues with your button switch, consider the following:

  • Switch Not Functioning:
    • Check all wiring connections to ensure they are secure and correctly matched to the terminal markings.
    • Verify that the power supply voltage matches the LED voltage version of your switch.
    • Ensure the rated current of your application does not exceed the switch's 20A/250VAC capacity.
    • If the switch stops working shortly after installation, inspect for any signs of damage or incorrect wiring during installation.
  • Incorrect Product Received:
    • If the item received does not match your order (e.g., wrong size, color, or type), please contact customer service for assistance.

9. User Tips

  • Verify Amperage: If the amperage rating is critical for your application, it is advisable to verify it, as some units may not have it explicitly marked on the button itself.
  • Check Dimensions: Before cutting mounting holes, double-check the exact diameter (16mm, 19mm, or 22mm) of your specific switch model to ensure a proper fit.
  • LED Brightness: The LED light colors are generally bright, which is useful for clear indication.

10. Warranty & Support

This product comes with a one-year warranty. For any questions, custom configurations, or issues not covered in this manual, please contact the seller's customer service. You can also refer to the official user manual PDF for additional details:

View User Manual (PDF)

Video: Demonstration of various colors and sizes of the metal button switches.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.