yuyi 1318612-1

Contents

Automotive ECU Connector and PCB Mount Header Instruction Manual

Model: 1318612-1, 353027, 353028, 353029, 1318682

Brand: Yuyi

1. Introduction

This manual provides essential information for the safe and effective use of the Yuyi 17P/22P/24P/31P/125 Pin PCB Mount Header Connector and ECU Plug Sockets. These connectors are designed for various automotive applications, including specific models from Honda (K20, K24), Toyota, and Nissan. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.

2. Safety & Warnings

Important Safety Information:

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Non-professionals should not use this product.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.

3. Product Overview

The product includes a range of PCB mount header connectors and ECU plug sockets with varying pin configurations to suit different automotive wiring needs. The available pin counts are 17P, 22P, 24P, 31P, and a larger 125P header connector.

Front view of various pin connectors (31P, 24P, 22P, 17P, 31P) and a 125P header, with a single pin.
Figure 1: Assortment of ECU plug sockets (31P, 24P, 22P, 17P) and the 125P PCB mount header connector, along with a single pin.
Image of the '5 in 1 with Pin' variant, showing the various pin count connectors and a single pin.
Figure 2: The '5 in 1 with Pin' variant, illustrating the different connector sizes and a loose pin.

The connectors are designed for secure and reliable electrical connections within vehicle systems.

4. Setup and Installation

Proper installation is crucial for the performance and longevity of these connectors. It is recommended that installation be performed by qualified personnel.

4.1 Required Tools

  • Professional crimping pliers (essential for secure pin attachment).
  • Wire strippers.
  • Multimeter (for continuity testing).
  • Heat shrink tubing or electrical tape (for insulation, if needed).

4.2 Installation Steps

  1. Wire Preparation: Carefully strip the insulation from the ends of the wires to be connected, ensuring the correct length for crimping. Avoid damaging the wire strands.
  2. Pin Crimping: Insert the stripped wire into the appropriate terminal pin. Use professional crimping pliers to securely crimp the pin onto the wire. Ensure a strong mechanical and electrical connection.
  3. Terminal Insertion: Insert the crimped terminal pin into the correct cavity of the connector housing. Listen for a click, indicating the terminal is locked in place. Gently pull on the wire to confirm it is secure.
  4. Connector Assembly: Once all terminals are inserted, ensure the connector halves (if applicable) are fully seated and locked.
  5. Verification: Before connecting to the ECU or PCB, use a multimeter to check for continuity and ensure there are no short circuits between pins.
Top-down view of the 125P PCB mount header connector and smaller ECU plugs, showing pin receptacles.
Figure 3: Top-down view of connector receptacles, illustrating the precise fit for pins.

5. Operating Instructions

These connectors are passive components designed to facilitate electrical connections. Proper operation primarily involves ensuring secure mating and unmating procedures.

  • Connecting: Align the male and female parts of the connector carefully. Push them together firmly until they click into place, indicating a secure connection. Do not force the connection if resistance is met; re-check alignment.
  • Disconnecting: If the connector has a locking tab, press or pull the tab as required by the design, then gently pull the connectors apart. Never pull directly on the wires to disconnect, as this can damage the terminals or wires.

6. Maintenance

These connectors are generally low-maintenance. However, periodic inspection can help ensure reliable performance.

  • Cleaning: If connectors become dirty, disconnect them and use a non-conductive electrical contact cleaner. Ensure connectors are completely dry before re-connecting.
  • Inspection: Periodically check for signs of wear, corrosion, or damage to the housing and terminals. Replace any damaged connectors immediately.
  • Environmental Protection: While designed for automotive use, avoid prolonged exposure to extreme moisture, dust, or corrosive chemicals unless the specific connector variant is rated for such conditions.

7. Troubleshooting

If you experience issues with your electrical connections, consider the following common troubleshooting steps:

  • No Connection/Intermittent Connection:
    • Check if the connector is fully seated and locked.
    • Inspect individual crimped pins for looseness or poor contact.
    • Verify wire continuity using a multimeter.
    • Look for signs of corrosion on terminals; clean if necessary.
  • Short Circuit:
    • Ensure no bare wires are touching within the connector housing.
    • Check for damaged insulation on wires leading to the connector.
    • Verify correct pin insertion to prevent misaligned contacts.
  • Difficulty Connecting/Disconnecting:
    • Ensure correct alignment of male and female parts.
    • Check for bent or damaged pins.
    • Verify that locking tabs are functioning correctly.

8. Specifications

Attribute Value
Brand Name yuyi
Model Number 1318612-1, 353027, 353028, 353029, 1318682
Origin Mainland China
Application Automotive (Honda K20 K24, Toyota, Nissan)
Position 17P/22P/24P/31P/125 Pin car connector
Type 1.0 mm series plug
Unit piece/pcs/set/kit
Package Length 10 cm
Package Width 10 cm
Package Height 3 cm
Package Weight 0.13 kg

Compliance: CE Certified

9. User Tips

  • Always double-check the pinout diagram for your specific vehicle and ECU before inserting terminals to avoid damage.
  • When working with multiple connectors, label wires or use color-coding to prevent confusion during assembly.
  • Store unused connectors and pins in a dry, clean environment to prevent corrosion and damage.

10. Manufacturer & Support Information

Manufacturer:

Yueqing ChenYi Electric Co., Ltd
Address: 2nd Floor, Building 3, No. 12 Yongxing 1st Road, Chengdong Industrial Functional Zone, Chengdong Street, Yueqing City, Zhejiang Province, China
Phone: +86-15869652718

EU Authorized Representative:

EUREPSTAR GmbH
Address: Schlüterstr. 3, 85057 Ingolstadt, Germany
Phone: +49-84188697744
Email: eurep@eurep-gmbh.de

For further assistance or inquiries, please contact the manufacturer or their authorized representative.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.