1. Introduction
This manual provides detailed instructions for the installation, configuration, and operation of the HORACO AFGW-SWTG218ANS 2.5G Web Managed PoE Switch. This high-performance switch features 8x2.5G PoE ports and 1x10G SFP+ slot, designed to meet the demands of modern network environments, including homelabs, supporting devices such as 2.5G NAS, WiFi 6 APs, firewalls, and WiFi 6 routers. It offers advanced management functions including VLAN, QoS, LACP, and robust security features.
Figure 1: Front view of the HORACO 8 Port 2.5GbE Managed POE Switch, highlighting its web management support, 8x2.5G POE ports, and 1x10G SFP+ slot.
2. Safety Information
Please read and understand all safety instructions before installing or operating this device. Failure to do so may result in injury or damage to the equipment.
- Ensure the power supply voltage matches the device's requirements (AC 100-240V, 50/60Hz).
- Do not open the device casing. There are no user-serviceable parts inside.
- Keep the device away from water, fire, and high humidity environments.
- Ensure proper ventilation to prevent overheating.
- Use only the provided power adapter or a compatible replacement.
- The device features 6KV Lightning Protection. However, it is recommended to disconnect power during electrical storms.
Figure 2: Image depicting the switch with a lightning bolt icon, highlighting its 6KV Lightning Protection Design.
3. Package Contents
Please check the product packaging for the following items:
- HORACO 2.5G Web Managed PoE Switch (AFGW-SWTG218ANS)
- Power Adapter (DC 52V 2.88A)
- User Manual (this document, also available as PDF)
- Mounting accessories (if applicable)
4. Setup
4.1 Physical Installation
- Placement: Place the switch on a stable, flat surface or mount it in a rack (if rackmount accessories are used). Ensure adequate space around the device for proper airflow.
- Power Connection: Connect the provided power adapter to the switch's power input and then to a suitable electrical outlet.
Figure 3: Side view of the HORACO 2.5G PoE Switch connected to a server rack, showing network cables plugged into its ports and the power LED illuminated.
4.2 Network Connection
- Ethernet Ports: Connect your network devices (PCs, NAS, APs, etc.) to the 8x2.5G PoE Ethernet ports using standard Ethernet cables. The switch supports Plug and Play functionality.
- SFP+ Port: For high-speed uplink or connection to a 10G network, insert a compatible 10G SFP+ module (not included) into the SFP+ slot and connect it to your 10G device.
- PoE Devices: Power over Ethernet (PoE) devices (e.g., IP cameras, VoIP phones, WiFi 6 APs) can be connected directly to the PoE ports. The switch will automatically detect and power these devices if they are IEEE802.3af/at compliant.
Figure 4: Image showing the switch with cables connected, emphasizing its 'Plug and Play' feature with no configuration required, and noting support for 1G/2.5G/10G modules and 10G DAC (not included).
4.3 Initial Configuration (Web Management)
The switch can be managed via a web-based interface. Follow these steps for initial access:
- Connect PC: Connect your PC directly to any Ethernet port on the switch.
- Configure PC IP: Set your PC's IP address to be in the same network segment as the switch but with a different IP. For example, set your PC's IP to
192.168.2.x(where x is between 2 and 254) and the subnet mask to255.255.255.0. - Access Web UI: Open a web browser (Chrome 23.0+, Firefox 20.0+, or IE 9.0+) and type the default switch IP address:
http://192.168.2.1in the address bar, then press Enter. - Login: A login window will appear. Enter the default username
adminand default passwordadmin. Click "Log in".
Figure 5: Screenshot of the web management interface login screen, with a laptop displaying the login prompt.
5. Operating Instructions
The web management interface provides comprehensive control over the switch's functions. The main menu items are System, Configuration, Security, Monitoring, and Tools, each containing various submenus.
5.1 Web Management Interface Overview
Upon successful login, you will see the main operation interface. The navigation bar on the left provides access to different settings categories:
- System: View device information, configure IP settings, manage user accounts, and set port parameters.
- POE: Configure and monitor Power over Ethernet ports.
- Configuration: Advanced network settings including VLAN, QoS, Loop prevention, IGMP Snooping, Trunk Group, Port Mirroring, Port Isolation, Bandwidth Control, and Jumbo Frame.
- Security: MAC address management and Storm Control settings.
- Monitoring: View port statistics.
- Tools: Firmware upgrade, configuration backup/restore, reset, save, reboot, and logout options.
Figure 6: A monitor displaying the web management interface of the switch, showing port status, device information, and various configuration menus.
5.2 System Information
To view basic device information:
- Navigate to System > Information.
- This page displays details such as Device Model (ZX-AFGW-SWTG218ANS), MAC Address, IP Address, Netmask, Gateway, Firmware Version (V1.9), Firmware Date (Mar 04 2024), and Hardware Version (V1.1).
5.3 IP Setting
To change the management IP address of the switch:
- Navigate to System > IP Setting.
- You can enable/disable DHCP client, and manually configure IP Address, Netmask, and Gateway. Click "Apply" to save changes.
5.4 User Account
To modify the switch's login credentials:
- Navigate to System > User Account.
- Enter a New Username, New Password, and Confirm Password. Click "Apply".
5.5 Port Setting
To query and configure Ethernet ports:
- Navigate to System > Port Setting.
- Configure parameters such as Port State (Enable/Disable), Speed/Duplex (Auto, 10M/Half, 10M/Full, 100M/Half, 100M/Full, 1000M/Full, 2500M/Full), and Flow Control (On/Off). Click "Apply".
5.6 PoE Configuration
Power over Ethernet (PoE) allows data signal and electrical power transmission over the same Ethernet cables. This switch supports active PoE (IEEE 802.3af/at).
- PoE Port Configuration: Navigate to POE > POE Port configuration to check the PoE power supply settings.
- PoE Port Status: Navigate to POE > POE Port status to view the status of each PoE port, including Power On/Off, Type, Power(W), Voltage(V), and Current(mA).
5.7 VLAN Configuration
VLANs (Virtual Local Area Networks) allow logical segmentation of a physical LAN, enhancing security and bandwidth efficiency. The switch supports 802.1Q VLAN mode.
- 802.1Q VLAN: Navigate to Configuration > VLAN > 802.1Q VLAN. Here you can add/modify VLANs, assign ports as Untagged, Tagged, or Not Member. VLAN 1 is the system default and cannot be deleted.
- 802.1Q VID: Navigate to Configuration > VLAN > 802.1Q VID to set the Port VLAN ID (PVID) for each port.
5.8 QoS Configuration
Quality of Service (QoS) ensures optimal performance for critical network traffic by prioritizing data frames.
- Port to Queue: Navigate to Configuration > QOS > Port to Queue to set processing priorities for different data frame tags.
- Queue Weight: Navigate to Configuration > QOS > Queue Weight to configure the weight for each queue, ranging from 1 to 15 (Weighted Round Robin) or Strict Priority.
5.9 Loop Detection/Prevention
The switch can detect and prevent network loops, which can cause network instability.
- Loop Protocol: Navigate to Configuration > Loop > Loop Protocol to enable/disable loop detection, loop prevention, or Spanning Tree Protocol (STP).
- STP Global: Navigate to Configuration > Loop > STP global to configure global STP settings, including Force Version (RSTP), Priority, Maximum Age, Hello Time, and Forward Delay.
- STP Port: Navigate to Configuration > Loop > STP port to configure STP settings for individual ports, such as Path Cost, Priority, P2P, and Edge.
5.10 IGMP Snooping
IGMP Snooping manages and controls multicast groups, optimizing multicast traffic flow.
- Navigate to Configuration > IGMP.
- Enable or disable IGMP Snooping and view multicast group entries.
5.11 Trunk Group Setting (Link Aggregation)
Link Aggregation (LAG) bundles multiple physical interfaces into a single logical interface to increase bandwidth and reliability.
- Static Mode: Navigate to Configuration > Trunk Group Setting. Select "static" as the Type to manually configure Eth-Trunks and add member ports.
- LACP Mode: Select "LACP" as the Type for dynamic aggregation based on IEEE 802.3ad Standard. LACP dynamically aggregates and disaggregates links, providing redundant backup.
Figure 7: Diagram illustrating multiple management functions of the switch, including Link Aggregation, Loop Settings, and Port Isolation Settings.
5.12 Port-based Mirroring
Port Mirroring copies traffic from a source port to a destination port for network monitoring and troubleshooting.
- Navigate to Configuration > Port-based Mirroring.
- Configure the Mirror Direction (Rx, Tx, Both), Mirroring Port (source), and Mirrored Port List (destination).
5.13 Port Isolation
Port Isolation prevents direct communication between specified ports, enhancing security by isolating traffic.
- Navigate to Configuration > Port Isolation.
- Establish the member list of the interworking group for isolated ports.
5.14 Bandwidth Control
Bandwidth Control allows you to restrict the data transmission and reception rates on physical interfaces.
- Navigate to Configuration > Bandwidth Control.
- Configure Ingress (inbound) and Egress (outgoing) rate limits for each port.
5.15 Jumbo Frame
Jumbo Frames are Ethernet frames larger than the standard 1500-byte MTU (Maximum Transmission Unit), which can improve network efficiency for large data transfers.
- Navigate to Configuration > Jumbo Frame.
- Set the MTU of the port (e.g., 16353 bytes).
5.16 MAC Address Management
The switch maintains a MAC address forwarding table for efficient Layer 2 communication.
- MAC Search: Navigate to Security > MAC Address > MAC Search to display the MAC address table.
- Static MAC: Navigate to Security > MAC Address > Static MAC to manually configure static MAC entries, which do not age out.
5.17 Storm Control
Storm Control prevents network performance degradation caused by excessive broadcast, unknown multicast, or unicast messages.
- Navigate to Security > Storm Control.
- Configure rate limits for Broadcast, Multicast, and Unicast storm types for each port.
5.18 Monitoring (Port Statistics)
To view real-time traffic statistics for each port:
- Navigate to Monitoring > Port Statistics.
- This page displays information such as Link Status, TxGoodPkt, TxBadPkt, RxGoodPkt, and RxBadPkt.
5.19 Tools
The Tools section provides essential maintenance and management functions:
- Firmware Upgrade: Navigate to Tools > Firmware Upgrade to update the switch's firmware. Do not power off during the upgrade process.
- Configuration Backup: Navigate to Tools > Configuration Backup to save the current configuration to your computer.
- Reset: Navigate to Tools > Reset to restore the switch to factory default settings. This will also reboot the system.
- Save: Navigate to Tools > Save to save the current running configuration. This is crucial to prevent losing settings after a reboot.
- Reboot: Navigate to Tools > Reboot to restart the switch.
- Logout: Navigate to Tools > Logout to exit the web management interface.
6. Troubleshooting
- Cannot access Web UI:
- Ensure your PC's IP address is in the same subnet as the switch (e.g., 192.168.2.x, subnet 255.255.255.0).
- Verify the switch is powered on and connected to your PC.
- Try a different web browser.
- Reboot the switch and try again.
- Configuration changes are lost after reboot:
- Always navigate to Tools > Save after making any configuration changes to permanently store them.
- PoE devices not powering on:
- Ensure the connected device is PoE compatible (IEEE 802.3af/at).
- Check the PoE Port status in the web UI to confirm power delivery.
- Verify the total PoE power budget (85W) is not exceeded by all connected devices.
7. Specifications
| Attribute | Value |
|---|---|
| Brand Name | HORACO |
| Model Number | AFGW-SWTG218ANS |
| Switch Type | Ethernet, Web Managed POE |
| Number of Interfaces | 9 |
| Ethernet Ports | 8*100/1000/2500M POE port + 1*10G SFP+ port |
| Transmission Rate | 10/100/1000Mbps/2.5G/10Gbps |
| Switch Capacity | 60Gbps |
| Packet Forward Rate | 44.64Mpps |
| Communication Mode | Full-Duplex & Half-Duplex |
| Function | POE, Lightning Protection, Plug and Play |
| VLAN Support | YES |
| MAC Address Table Size | 4K |
| Chipset | RTL8373+RTL8224 RTL8238B |
| Forwarding Mode | Storage & forward |
| Power | AC 100-240V, 50/60Hz, DC 52V 2.88A |
| Mainboard Power Consumption | 11.29W |
| PoE Power Budget | 85W |
| Certification | CE, FCC, RoHS |
| Origin | Mainland China |
| Package Weight | 1.3 kg |
| Package Dimensions | 32cm (L) x 22cm (W) x 9cm (H) |
8. User Tips
- Always Save Configuration: Remember to navigate to Tools > Save in the web interface after making any changes to prevent losing your settings upon reboot.
- Active PoE Support: This switch supports active PoE (IEEE 802.3af/at), ensuring compatibility with a wide range of standard PoE devices.
- Robust VLAN Functionality: Users have reported excellent and robust operation of VLANs, confirming the switch's capability for network segmentation.
- Plug and Play Convenience: While offering advanced web management, the switch also provides reliable plug-and-play functionality for basic network connections.
9. Warranty and Support
For technical support, troubleshooting assistance, or warranty inquiries, please contact HORACO Official Store directly. Refer to the official product page or your purchase documentation for contact details.
A detailed Web Manual (Ver. 1.0) in PDF format is available for download, providing further in-depth information on configuration and management. You can find it at: HORACO AFGW-SWTG218ANS Web Manual (PDF)