1. Introduction
Thank you for choosing our LED Street Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting product. Please read this manual thoroughly before installation and keep it for future reference.

Figure 1: LED Street Light in an outdoor setting
2. Safety Instructions
- Warning: Installation must be performed by a professional electrician to ensure correct and firm wiring, preventing electrical hazards.
- Always disconnect power before installation, maintenance, or cleaning.
- Do not connect the lamp to DC power or voltage exceeding 265V; this will damage the lamp and pose safety risks.
- Ensure the product is securely mounted to prevent it from falling.
- Do not look directly into the LED light source when it is on, as it may cause eye strain or damage.
3. Package Contents
Please check the package for the following items:
- 1 x LED Street Light Head
- Mounting Brackets (U-shaped)
- Screws and Washers

Figure 2: Product and included mounting hardware
4. Setup and Installation
4.1. Installation Environment
- Do not install the lamp in flammable, explosive, corrosive, or other harsh environments.
- Avoid installing it in places with strong vibration, which may cause loose parts and affect use.
- Ensure the mounting surface or pole is sturdy enough to support the weight of the fixture.
4.2. Mounting Instructions
- Position the LED street light head at the desired location on a pole or suitable mounting arm.
- Attach the U-shaped mounting brackets to the fixture and secure it to the pole using the provided screws and washers. Ensure all fasteners are tightened firmly.
- Adjust the angle of the light fixture to achieve optimal illumination coverage.
4.3. Electrical Wiring
- Ensure the main power supply is turned OFF at the circuit breaker before beginning any wiring.
- The lamp is designed for AC85-265V wide voltage. Connect the live, neutral, and ground wires from your power source to the corresponding wires of the street light fixture.
- Use appropriate waterproof connectors and ensure all connections are secure and insulated to prevent short circuits and water ingress.
- After wiring, ensure the wire connection cover is properly sealed to maintain the IP66 waterproof performance.
- Once wiring is complete and secure, restore power to test the light.
5. Operating Instructions
This LED Street Light is designed for straightforward operation. Once properly installed and wired to a power source, the light will illuminate when power is supplied. There are no external controls or settings on the fixture itself.
6. Maintenance
6.1. Cleaning
- Periodically clean the surface of the lamp and the lens with a soft, damp cloth to remove dust, dirt, and debris. This ensures optimal light output.
- Do not use abrasive cleaners or solvents, as they may damage the fixture's finish or lens.
6.2. Heat Dissipation
- The aluminum lamp shell is designed for efficient heat dissipation.
- Do not cover the lamp shell with cloth, plastic bags, or any other objects that could obstruct airflow and affect heat dissipation during use. This can lead to overheating and shorten the service life of the lamp.
6.3. Waterproof & Dustproof
- The product has an IP66 protection grade, making it resistant to heavy rain, dust, and other outdoor environmental factors.
- Do not immerse the lamp in water for extended periods.
- Ensure the lamp shell and wire connection cover remain undamaged to maintain waterproof performance.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on | No power supply Loose or incorrect wiring Faulty fixture | Check power source and circuit breaker. Have a professional electrician inspect wiring connections. Contact customer support if the fixture is faulty. |
| Light is dim or flickers | Dirty lens Unstable power supply Loose wiring | Clean the lens surface. Ensure stable voltage supply. Have a professional electrician check wiring. |
| Light turns off unexpectedly | Overheating Intermittent power supply | Ensure proper ventilation and no obstructions around the fixture. Check power supply stability. |
8. Specifications

Figure 3: Product Specifications and Dimensions
| Feature | Specification |
|---|---|
| Model | LED Street Light |
| Input Voltage | AC85-265V |
| Power | 200W |
| Color Temperature | Cool White: 6000-6500K |
| Luminous Flux | 100-110lm/W |
| Lamp Shell Material | Aluminum |
| Light Source | LED Chip |
| Protection Grade | IP66 |
| LED Quantity | 216 |
| Dimensions (L x W x D) | 54cm (21.25in) x 18cm (7.08in) x 2.2cm (0.86in) |
| Warranty | 3 Years |
| Certifications | CE, RoHS |
9. User Tips
- Optimal Placement: Consider the area you need to illuminate and position the light at a height and angle that provides the best coverage without creating excessive glare.
- Regular Inspection: Periodically check the mounting hardware for tightness, especially after severe weather conditions, to ensure the fixture remains securely in place.
10. Warranty and Support
10.1. Warranty Information
This LED Street Light comes with a 3-year warranty from the date of purchase, covering manufacturing defects. The warranty does not cover damage caused by improper installation, misuse, accidents, unauthorized repairs, or normal wear and tear.
10.2. Customer Support
If you encounter any issues with your product or have questions not covered in this manual, please contact the seller or your point of purchase for assistance. Please have your purchase details ready when contacting support.
For a more detailed user manual, you may refer to the PDF document available at: Detailed User Manual (PDF)