Introduction
This manual provides essential information for the safe and effective use of your SHIMANO ULTEGRA Di2 ST-R8170 Dual Control Levers and BR-R8170 Hydraulic Disc Brake Calipers. This system is designed for road bikes, offering 2x12 speed electronic shifting and powerful hydraulic disc braking. Please read this manual thoroughly before installation and use, and keep it for future reference.
Safety Information
Δ WARNING
- This product is not a toy and is not suitable for children under 16 years old without adult supervision.
- Keep all small parts (e.g., screws, pulleys) away from infants and toddlers to avoid choking hazards.
- Always wear appropriate protective gear (helmet, gloves, knee pads) when operating the bicycle with this derailleur.
- Do not use the product in traffic without proper training.
- Ensure the derailleur is correctly installed and adjusted before use. Improper installation may cause chain slippage, leading to falls or serious injury.
- Do not modify the derailleur's structure or components. Unauthorized modifications void compliance and safety guarantees.
- This product is not intended for use with children's bicycles (refer to EN 14765 for children-specific requirements).
- Keep the derailleur away from corrosive substances (acids, solvents) and extreme temperatures to prevent mechanical failure.
Additional Safety Notes:
- Regularly inspect the derailleur for wear, damage, or loose connections. Replace worn parts immediately using genuine Shimano accessories.
Setup and Installation
Proper installation is crucial for the performance and safety of your SHIMANO ULTEGRA Di2 system. It is highly recommended that installation be performed by a qualified bicycle mechanic.
Component Overview:
Brake Caliper Mounting:
The BR-R8170 brake calipers are designed for specific rotor sizes. Refer to the markings on the caliper for compatibility:
Ensure you use the correct rotor size (Ø160mm or Ø180mm) and corresponding mounting adapter if necessary, as indicated on the caliper: "For Ø160 or Ø180 for 160/180 mount".
Included Small Parts:
The system includes various small parts essential for installation and maintenance, such as brake pad spacers, bolts, and pins.
For detailed installation instructions, including hydraulic hose routing, bleeding procedures, and electronic cable connections, please refer to the official Shimano technical documentation or consult a professional bicycle mechanic.
Operating Instructions
Dual Control Levers (ST-R8170):
The ST-R8170 levers combine electronic shifting and hydraulic braking into a single unit. The levers are designed for intuitive operation:
- Shifting: Use the buttons on the levers to actuate the Di2 electronic derailleur system for smooth and precise gear changes. Consult the specific Di2 system manual for customization of button functions.
- Braking: Squeeze the levers to engage the hydraulic disc brakes. Apply even pressure for controlled deceleration.
Hydraulic Disc Brakes (BR-R8170):
The BR-R8170 calipers provide consistent and powerful braking performance in various conditions. Familiarize yourself with the brake feel and modulation before riding in challenging environments.
- Always test your brakes before each ride.
- Avoid sudden, hard braking, especially on wet or loose surfaces, to prevent loss of control.
- Brake pads will wear over time and require replacement.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your SHIMANO ULTEGRA Di2 system.
- Inspection: Inspect the derailleur, brake levers, and calipers for wear, damage, or loose connections every 500km or every 3 months, whichever comes first.
- Lubrication: Lubricate the derailleur and other moving parts as recommended by Shimano.
- Brake Fluid: Check hydraulic brake fluid levels and bleed the system as needed. Use only genuine Shimano mineral oil.
- Brake Pads: Replace worn brake pads promptly.
- Cleaning: Keep components clean, especially after riding in dirty or wet conditions. Avoid using high-pressure washers directly on bearings or electronic components.
- Environmental Restrictions: Do not use in saltwater environments (e.g., coastal areas) without proper corrosion protection.
Troubleshooting
This section addresses common issues you might encounter. For complex problems, consult a professional bicycle mechanic.
Common Issues:
- Poor Shifting Performance:
- Check battery level of the Di2 system.
- Ensure electronic cables are securely connected.
- Verify derailleur adjustment and alignment.
- Weak or Spongy Brakes:
- Check brake pad wear and replace if necessary.
- Inspect for air in the hydraulic system; bleeding may be required.
- Check for hydraulic fluid leaks.
- Brake Rubbing:
- Ensure brake calipers are properly aligned with the rotor.
- Check for bent rotors.
- Verify wheel is correctly seated in the dropouts.
Specifications
| Feature | Specification |
|---|---|
| Brand Name | SHIMANO |
| Model Number | R8170 (ST-R8170 + BR-R8170) |
| Derailleur Groupset Type | Electronic Derailleur system (Di2) |
| Gears | 12 Speed (2x12) |
| Type | Shifter / Hydraulic Disc Brake |
| Components | Derailleurs, Brake Calipers, Dual Control Levers |
| Origin | Japan |
| Brake Caliper Pistons | 2-Piston |
| Rotor Compatibility | Ø160mm or Ø180mm (for 160/180 mount) |
| High-concerned chemical | None |
User Tips
- Compatibility Check: Before purchasing or installing, always verify that the 2x12 speed system is compatible with your bicycle frame and other components (e.g., crankset, cassette).
- Lever Configuration: The system typically includes both left and right dual control levers. If you require a single lever for a specific setup, ensure you purchase the correct configuration.
- Di2 Customization: Utilize the Shimano E-Tube Project software to customize Di2 shifting functions, button assignments, and update firmware for optimal performance.
Compliance Information
Applicable Regulations & Harmonized Standards:
This product complies with the following EU regulations and standards:
- General Product Safety Directive (GPSD): 2001/95/EC
- Mechanical Directive (MD): 2006/42/EC
Harmonized Standards:
- EN ISO 4210-2:2015 (Bicycle safety requirements for city, trekking, mountain bikes)
- EN 14781:2015 (Racing bicycle specific safety standards)
- REACH Regulation (EC) No 1907/2006 (Restriction of hazardous substances)
Usage Restrictions:
Not Suitable For:
- Children under 16 years old (without adult supervision)
- Bicycles with wheel sizes below 26" or above 29"
- Electric bicycles with motor power exceeding 250W
- Off-road use in extreme conditions (e.g., rock climbing, steep descents >30°)
EU Declaration of Conformity (DoC):
This product (Shimano Bicycle Derailleur, Model: Universal Fit for Road/Gravel/MTB/E-Bike) meets the essential requirements of EU Directive 2006/42/EC (Mechanical Directive) and related harmonized standards. The EU Authorized Representative is responsible for ensuring compliance with EU market surveillance requirements. A complete copy of the DoC is available upon request from the EU Responsible Person.
Manufacturer Information and Support
Manufacturer: Shimano Inc.
Address: 3-1-1 Sakai-cho, Sakai-ku, Osaka, Japan
Contact: support@shimano.com
EU Responsible Person (Authorized Representative):
Name: MJCM SARL
Country: France
Address: 78 avenue des Champs Elysees, Bureau 326, 75008 Paris, France
Phone: +33-752907452
Email: mjcm190928@gmail.com
A detailed user manual in PDF format is also available for download. You can find it at the following reference: Official User Manual (PDF).