Introduction
Thank you for purchasing the Riderace RN2254 Bicycle Rear View Mirror. This manual provides essential information for the safe and effective installation, operation, and maintenance of your new mirror. Please read all instructions carefully before use and retain this manual for future reference.
Safety & Warnings
Important Safety Information:
- Read all instructions before use. Failure to follow these instructions may result in damage to the device, product, or personal injury.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Handle with care to avoid cuts or injuries.
- Stop using immediately if the product is cracked, damaged, or loose.
Setup and Installation
Ensure the specifications and size of the mirror mount match your bicycle's handlebar diameter. This mirror is designed for handlebars with a diameter between 22-25mm.
Installation Steps:
- Prepare the Handlebar: Ensure the area on your handlebar where you intend to mount the mirror is clean and free of obstructions.
- Place the Base: Position the mirror mount base onto the desired location on your handlebar. If your handlebar is on the smaller side of the 22-25mm range, use the approximately 2mm thick shim provided for a secure fit.
- Secure the Base: Use a hex wrench to tighten the screws on the mirror mount base firmly. Do not over-tighten.
- Attach the Mirror Arm: Insert the connecting rod of the mirror into the base.
- Tighten Connecting Rod Screws: Use a hex wrench to tighten the screws that secure the mirror's connecting rod to the base.
- Adjust Mirror Angle: The mirror features a multi-angle rotatable universal ball joint and can rotate 360 degrees. Adjust the mirror to your preferred viewing angle.
- Final Fixation: Once the desired angle is achieved, use a wrench to ensure all connections are secure.
Operating Instructions
The Riderace RN2254 mirror is designed for optimal rear visibility during cycling. After installation, ensure the mirror is adjusted to provide a clear and wide field of view of the area behind you.
- 360° Free Adjustment: The rearview mirror is installed on the handlebar and can be adjusted from multiple angles and directions. Utilize the 360° rotation and the multi-angle rotatable universal ball to find the most suitable angle for your riding posture and visibility needs.
- High Definition View: The mirror features a high-definition stainless steel mirror surface designed to reduce dizziness and improve cycling safety by providing a clear, wide field of view.
Care & Maintenance
- Cleaning: Clean dust and mud from the mirror and bracket regularly. Keep the mirror dry.
- Environmental Exposure: Avoid long-term exposure to direct sunlight, heavy rain, or extremely high temperatures, as this can affect the material's longevity.
- Part Replacement: Replace any parts immediately if they show signs of wear beyond their limit.
- Regular Checks: Periodically check the mirror's mounting and adjustment points to ensure they remain secure.
- Storage: For long-term storage, clean the mirror, lubricate any moving parts if necessary, and store it in a dry, well-ventilated place.
Troubleshooting
- Mirror is Loose or Vibrates: Check all screws on the mirror mount and connecting rod. Tighten them to standard torque. Ensure the handlebar diameter is within the 22-25mm range and the shim is used if necessary for a snug fit.
- Unclear View: Clean the mirror surface with a soft cloth and mild cleaner. Ensure no dirt or debris is obstructing the view.
- Mirror Does Not Hold Position: Ensure the universal ball joint and connecting rod screws are sufficiently tightened. If the joint feels worn, consider replacement.
- Visible Damage (Cracks, Deformation): Stop using the product immediately if any part is cracked, deformed, or otherwise damaged. Replace the unit to ensure safety.
Specifications
| Feature | Detail |
|---|---|
| Brand Name | riderace |
| Model Number | RN2254 |
| Origin | Mainland China |
| Product Name | High definition rearview mirror for bicycles |
| Material | Nylon + Stainless Steel (Bracket: PA+PP) |
| Mirror Type | Convex glass, High-definition stainless steel mirror surface |
| Weight | Approximately 432.5g (one pair) |
| Handlebar Diameter | 22-25mm |
| Function | 360° rotation, adjustable angles |
| Mirror Dimensions | 110.5mm (length) x 40mm (height) |
| Arm Length | 135mm (from mirror pivot to mount pivot) |
User Tips
No specific user tips from reviews or Q&A are available at this time. For optimal safety, always ensure your mirror is clean and properly adjusted before each ride.
Warranty & Support
For warranty information and support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty claims.
Manufacturer & EU Representative Information:
- Manufacturer: Ningbo Luoting Trade Co., Ltd., 302, 3rd Floor, Building 2, No.688 Jinda Road, Ningbo, Zhejiang, China.
- EU Authorized Representative: ORIENT CONSULTING SL, Avd.of the industry, 2, nv16, Fuenlabrada, Spain.
- Importer: Ningbo Luoting Trade Co.Ltd., 302, 3rd Floor, Building 2, No.688 Jinda Road, Ningbo, Zhejiang, China.