Instruction Manual: Yamaha MT-09 / MT09 SP Non-slip Side Fuel Tank Stickers

Introduction

This manual provides comprehensive instructions for the installation, use, and maintenance of your Yamaha MT-09 / MT09 SP non-slip side fuel tank stickers. These high-density rubber pads are designed to enhance rider grip and control, while also protecting the fuel tank from scratches and wear marks. Please read this manual thoroughly before installation to ensure proper application and longevity of the product.

Safety Information

EU Regulations Compliance:

• This product complies with EU Regulation (EC) No 1272/2008 (CLP) on classification, labelling and packaging of substances and mixtures.
• In accordance with EU REACH Regulation (EC) No 1907/2006, this product does not contain substances of very high concern above threshold concentrations.
• Product meets requirements of Directive 2008/68/EC on the inland transport of dangerous goods.
• Manufactured in compliance with ISO 9001:2015 quality management standards.
• Disposal must comply with EU Directive 2002/96/EC (WEEE) on waste electrical and electronic equipment.

CE Marking Declaration: This product bears the CE marking indicating conformity with European health, safety, and environmental protection standards.

Hazard Statements (EU CLP):

• H225: Highly flammable liquid and vapor
• H315: Causes skin irritation
• H319: Causes serious eye irritation
• H336: May cause drowsiness or dizziness

Precautionary Statements (EU CLP):

• P101: If medical advice is needed, have product container or label at hand.
• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P233: Keep container tightly closed.
• P240: Ground and bond container and receiving equipment.
• P241: Use explosion-proof electrical/ventilating/lighting/.../equipment.
• P242: Use only non-sparking tools.
• P243: Take precautionary measures against static discharge.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P370+P378: In case of fire: Use powder, CO₂, water spray, foam for extinction.

For a complete list of safety information, please refer to the official user manual PDF: User Manual (PDF)

Setup and Installation

The tank pad set includes a top water tank pad and two side grip pads for the left and right sides of the fuel tank. Proper installation is crucial for optimal adhesion and performance.

Step 1: Cleaning & Drying

1. Rinse with water: Thoroughly wipe the fuel cap and surrounding area with a wet cloth, focusing on removing oil and dust.
2. Stubborn stains: Apply a drop of dish soap to your finger, scrub gently, then immediately rinse with clean water to prevent residue.
3. Full drying: Air-dry naturally or wipe with a dry cloth. Ensure zero moisture by touch. Wait 10 minutes for safety.

Step 2: Applying Adhesion Promoter (Critical Step)

• Direct application: Tear open the adhesion promoter packet. Squeeze onto your finger or a clean cloth corner.
• Even thin coat: Apply in circular motions across the installation area, ensuring the promoter covers an area slightly larger than the sticker size.
• Drying standard: Wait 5 minutes until the promoter is transparent and non-sticky to light finger touch.

Pro Tip: Less is more! Excess promoter reduces adhesion.

Step 3: Mounting & Sealing

1. Peel backing: Remove only 1/3 of the backing paper. Align and fix the top edge first.
2. Peel-and-press technique:
   • Use your left hand to slowly peel the remaining backing.
   • Use your right hand to press firmly with your palm heel, working from the center towards the edges.
3. Edge reinforcement: Roll-press the edges 3 times with your thumb to ensure a secure seal.

Operating Instructions

Once properly installed, the non-slip fuel tank stickers provide enhanced grip and control for the rider, especially during aggressive riding or cornering. The textured surface allows for better knee and leg contact with the tank, reducing fatigue and improving stability. Additionally, the pads act as a protective barrier against scratches and wear marks caused by riding gear.

Maintenance

Step 4: Inspection & Curing

• Adhesion test: Press the sticker center firmly. Zero lift indicates successful adhesion.
• 72-hour critical care:
  • NO sun exposure: Park in shade (UV + heat = cracking).
  • NO washing/rain: Avoid for at least 24 hours after installation. The adhesive on the side fuel tank pads must be hardened for 24 hours before the first ride.

After the initial 72-hour curing period, the tank pads are designed for durability. Clean the pads with mild soap and water as needed, avoiding harsh chemicals or abrasive scrubbers that could damage the rubber or adhesive.

Troubleshooting

Adhesion Issues:

• Pads not sticking well: Ensure the tank surface was thoroughly cleaned and dried before application. Any oil, dust, or moisture will compromise adhesion.
• Pads lifting at edges: Re-apply pressure to the edges, especially during the initial installation. Ensure the adhesion promoter was applied evenly and allowed to dry for 5 minutes. Remember, excess promoter can reduce adhesion.
• Pads coming off: This often indicates insufficient curing time or improper surface preparation. Ensure the 72-hour critical care period (no sun, no washing/rain for 24 hours) is strictly followed. If issues persist, consider re-cleaning the surface and applying new pads, ensuring all steps are followed precisely.

Specifications

User Tips

• Many users report excellent grip and control after proper installation.
• Ensure the tank surface is meticulously clean and dry before applying the pads to maximize adhesion.
• Pay close attention to the curing time (72 hours) and avoid exposing the pads to sun or rain during the initial 24 hours to prevent issues with adhesion.
• The pads are designed to be identical to original Yamaha parts in appearance, offering a seamless look.

Warranty and Support

For detailed warranty information and further support, please refer to the official user manual PDF available at: User Manual (PDF). This document contains comprehensive safety data and compliance details.

For any product-related inquiries or assistance, please contact your retailer or the manufacturer directly.