ZOOM HB-775E

Contents

ZOOM HB-775E E-Bike Hydraulic Disc Brake Set User Manual

Model: HB-775E

1. Introduction and Safety Warnings

This manual provides detailed instructions for the installation, adjustment, maintenance, and troubleshooting of your ZOOM HB-775E E-Bike Hydraulic Disc Brake Set. Please read this manual thoroughly before use to ensure safe and optimal performance.

Important Safety Warnings:

  • High Temperature Warning: The caliper body and disc can become very hot during braking. Do not touch these parts immediately after riding to avoid injury. Allow them to cool sufficiently before performing any maintenance.
  • Wet Conditions: Braking distance increases significantly in wet conditions. Reduce speed and brake cautiously when riding in rain or on wet surfaces.
  • Tire Skid Risk: Wet roads can cause tires to skid, leading to falls. Exercise extreme caution and reduce speed.
  • Pre-Ride Check: Always ensure the brake system is operating correctly before each ride.
  • Oil Contamination: Prevent oil from contaminating the disc and brake pads. Oil contamination can lead to brake failure. If brake pads are stained with oil, replace them. If the disc is stained, clean it thoroughly.
  • Brake Pad Wear: If you hear noise during braking, it may indicate worn brake pads. Check brake pad thickness; replace if less than 0.8mm or if the replacement mark is visible.
  • Brake Fluid: Use only ZOOM mineral oil (compatible with Shimano and Yannao mineral oil). Using other brake fluids can cause brake failure, air lock, or damage to the system.
  • Air Lock Phenomenon: Water or air bubbles in the brake system can expand when heated, causing the piston to protrude abnormally, leading to sudden brake action or failure.
    • Use only freshly opened or completely sealed brake oil.
    • Do not re-inject oil that has been discharged from the oil inlet nozzle.
    • Avoid frequent braking to prevent air lock.
  • Inverted Vehicle: The ZOOM system is not designed for inverted vehicle states. If the bicycle is inverted or placed horizontally for an extended period, air bubbles may move into the main body of the caliper, causing brake failure. Always check brake function after the bicycle has been inverted.
  • Oil Leakage: If oil leakage occurs, stop using the bicycle immediately and repair it. Continuing to ride with oil leakage is dangerous.
  • Quick Release Handle: Ensure the quick release handle is on the right side (opposite the disc) to avoid collision with the disc.
  • Component Compatibility: Use only original ZOOM components (disc handle, caliper body, 140mm, 160mm, 180mm, 203mm discs, and brake block assemblies) for optimal performance.
  • Fasteners: Regularly check screws and nuts for looseness or damage. Tighten to specified torque values.

Mineral Oil Usage Precautions:

  • Eye Contact: Wear safety glasses. If oil enters eyes, wash immediately with clean water and seek medical attention.
  • Skin Contact: Wear protective gloves. If oil touches skin, wash thoroughly with soapy water.
  • Inhalation: Ensure good air circulation. If you feel unwell after inhaling oil fumes, seek fresh air.
  • Ingestion: Do not drink mineral oil. If ingested, seek medical attention immediately.
  • Storage: Keep out of reach of children.

Waste Oil Disposal:

Dispose of waste oil according to local regulations.

Storage Method:

Store in a sealed container, away from direct sunlight, in a cool, dark place, free from foreign matter and moisture.

2. Product Overview and Specifications

The ZOOM HB-775E is a hydraulic disc brake set designed for E-bikes, electric scooters, and folding MTB bikes, featuring a power-off ebrake function for enhanced safety.

ZOOM HB-775E E-Bike Hydraulic Disc Brake Set components

Figure 2.1: Overview of the ZOOM HB-775E E-Bike Hydraulic Disc Brake Set, highlighting the power-off feature.

ZOOM HB-775E E-Bike Hydraulic Disc Brake Set complete kit

Figure 2.2: Complete kit contents including brake levers, calipers, hoses, and mounting hardware.

Key Features:

  • Hydraulic Disc Brake System
  • Power-off Ebrake Function
  • Integrated Cast Caliper for stability and durability
  • Steel Piston for enhanced durability and stability
  • Brake Stroke Adjustment

Specifications:

AttributeValue
Model NumberHB775E
TypeHydraulic Disc Brake
Braking SystemHydraulic Disc Brake (Hydraulic Brake Pad)
Hose Length (Size)1100mm / 1850mm (Front/Rear)
Brake Lever Length90mm
Clamp Diameter22.2mm
Power-off Cable Length45mm
Brake Pad Dimensions32.5mm x 27mm
OriginMainland China
Power-off cable length and connector detail

Figure 2.3: Detail of the power-off cable, showing its 45mm length and connector type.

Brake lever dimensions and stroke adjustment

Figure 2.4: Brake lever dimensions (90mm) and the location of the brake stroke adjustment screw. Clamp diameter is 22.2mm.

Brake pad dimensions and compatibility

Figure 2.5: Brake pad dimensions (32.5mm x 27mm) and a list of compatible brake models (SHIMANO XT/R, DEORE, HONE, LX, BR-series, ZOOM HBIOO, HB870, HB875, HB775).

Caliper features: steel piston and integrated cast design

Figure 2.6: Caliper details, showing the durable steel piston and integrated cast design for stability.

3. Installation

Follow these steps carefully for proper installation of your disc brake system.

3.1 Disc Installation

  1. Install the disc onto the flower drum. Ensure the "ZOOM" logo on the disc faces outward, and the arrow indicates the correct rotation direction of the wheel.
  2. Loosely tighten the disc fixing screws to a half-tight state.
  3. To ensure the flatness of the disc, wear protective gloves and apply force to the disc clockwise while tightening the disc fixing screws in a diagonal order.
  4. Torque: Disc fixing screw locking element torque: 40-60 kgf-cm (35-52 lb-in).

3.2 Caliper Body Assembly

  1. Install the front disc brake and rear disc brake conversion seat onto the screw hole of the support.
  2. Loosen the caliper body fixing screws to allow the caliper body to be in a fine-tuning state.
  3. Install the conversion seat onto the frame.

3.3 Disc Handle Assembly

  1. First, fix the disc handle. Tighten one screw to a half-tight state, then tighten the other screw, and finally return to tighten the original screw.
  2. Torque: Disc brake handle locking torque: 60-80 kgf-cm (52-69 lb-in).
  3. Hold the disc handle under pressure and lock the caliper body fixing screws while the disc is pressed by the disc block.
  4. Pump the disc brake several times to confirm normal brake action and check for oil leakage.
  5. Torque: Transfer seat fixing screw torque: 70-90 kgf-cm.

3.4 Brake Block Assembly and Replacement

Replace brake blocks if they are stained with oil or worn to 0.8mm thickness.

  1. Remove the wheel and take out the brake block from the main part of the brake.
  2. Clean the piston and its surroundings.
  3. Set the bicycle so that the oil groove of the disc brake is level with the ground.
  4. Screw out the sealing screw of the oil groove.
  5. Press the piston to its lowest position, ensuring it does not deflect or protrude. Be aware that oil in the oil groove may overflow.
  6. Install the new brake block and reinstall the wheel.
  7. Hold the brake handle several times to confirm that the handle is in a compacted state.
  8. After confirming no interference between the brake block and the disc, fix the wheel.
  9. After locking the sealing screw of the oil groove, return the disc handle to its original riding angle.

4. Adjustments

4.1 Brake Block and Disc Brake Caliper Body Adjustment

The ZOOM disc brake system automatically adjusts the clearance between the disc and brake block as the brake block wears. When replacing the brake block, press the piston vertically to the bottom with a slotted screwdriver.

Adjusting for Poor Piston Action:

If the piston on the caliper body moves unevenly, or if the brake block interferes with the disc, refer to the brake block replacement steps (Section 3.4).

4.2 Hand Grip Distance Adjustment

If the hand grip distance is too large or too small, or if the braking force needs temporary adjustment, use the micro-adjustment function via the connecting adjustment screw on the disc brake handle.

  • Use a 2mm hex wrench.
  • Turn clockwise to increase grip distance (maximum ~100mm).
  • Turn counter-clockwise to decrease grip distance (minimum ~80mm).
  • Note: If you turn clockwise to the maximum grip distance, the aluminum piston of the handle will move forward, making the handle easier to press and increasing braking force, but may invalidate the automatic oil replenishment function.
Hand grip adjustment screw diagram

Figure 4.1: Diagram showing the hand grip adjustment screw location.

4.3 Tubing Cutting

If the oil pipe length is too long for your assembled bicycle, it must be cut and adjusted.

Necessary Tools and Parts:

  • 8mm open-ended wrench
  • Oil pipe joint screw
  • Tubing cutting tool
  • Oil tube
  • Oil pipe hold down nut
  • Tubing copper sleeve
  • Oil needle

Operation Steps:

  1. Push the oil pipe fixing screw sheath towards the oil pipe.
  2. Use an 8mm open-ended wrench to unscrew the oil pipe fixing screw. Be careful of brake oil leakage.
  3. Determine the required oil pipe length and cut off the excess (at least 15mm) with the tubing cutting tool. Ensure the cut is vertical to the oil pipe axis.
  4. Insert the oil pipe, copper sleeve, and oil pipe bushing (with type ring) into the oil pipe in sequence. Ensure the smaller end of the copper sleeve is fixed to the oil pipe.
  5. Press the oil pipe bushing into the oil pipe.
  6. Press the front end of the oil pipe into the front end of the disc handle until it reaches the bottom.
  7. While pressing the oil pipe, lock the oil pipe fixing screw on the disc handle with an 8mm open-ended wrench.
  8. Torque: Oil pipe fixing screw locking torque: 80-100 kgf-cm (6-10 NM).

4.4 Oil Replenishment Operation

Replenish oil when the oil level in the oil groove is insufficient or when the brake block is worn, making it impossible to firmly hold the disc brake handle.

Necessary Tools and Parts:

  • T15 M-shaped wrench
  • Transparent hose
  • Oil needle cylinder
  • Oil storage bottle

Operation Steps:

  1. Make the oil groove parallel to the ground.
  2. Remove the sealing screw of the oil groove with a T15 M-shaped wrench and the M6 oil inlet nozzle.
  3. Insert the transparent hose into the upper end of the M6 oil nozzle and connect the other end to the plastic hose.
  4. Draw an appropriate amount of vehicle oil from the oil storage tank with the transparent hose connected to the oil needle cylinder. Ensure no bubbles in the hose.
  5. Insert the oil needle cylinder into the upper body oil inlet nozzle.
  6. Use an 8mm open-ended wrench to tighten the loading body oil inlet nozzle (clockwise for about 1.5 turns).
  7. Formal Oil Replenishment: Press the brake handle by hand until no bubbles are discharged from the needle cylinder hose. If the effect is not obvious, press the needle cylinder by hand to make the brake oil enter the disc brake, then pull the needle cylinder to discharge the bubble. Repeat this action 3-5 times.
  8. Press and release the brake handle until no bubbles are discharged from the needle cylinder hose.
  9. Take out the needle cylinder, put the oil nozzle at the main end, and lock the oil injection screw.
  10. Hold the disc brake handle several times to ensure the grip feels solid.
  11. Remove the hose at the end of the caliper body. Be careful not to stain the brake block or disc with brake oil.
  12. Remove the hose at the handle end and replace the M6 oil nozzle with the oil groove sealing screw.
  13. Torque: Oil groove sealing screw locking torque: 30-40 kgf-cm.
  14. Clean any oil-stained parts of the disc brake handle and caliper body with alcohol or a clean cloth.
  15. Return the disc brake handle to its original position.
  16. If the oil in the oil tank changes color significantly, it is recommended to replace all the oil.

5. Maintenance

To maintain optimal performance of your ZOOM hydraulic disc brake system, perform the following inspections regularly.

5.1 Before Riding

  • Brake Block: Confirm that the brake block thickness is above the lower limit (0.2mm). Check for the replacement mark. Replace if necessary.
  • Oil Pipe: Check the oil pipe for cracks, wear, or other damage. Replace if necessary.

5.2 After Riding

  • Disc Cleaning: If dirt or impurities are present between the disc brake caliper body and the disc, clean it after riding. Ensure the disc or brake block is not stained with oil.

5.3 Periodic Inspection

  • Disc Brake Handle Lubrication: Lubricate the connecting rod with lubricating oil regularly.
  • Locking Screws: Check that all screws are tight and maintain the originally set locking torque.

Note: The effective shelf-life period of this product is one year.

6. Troubleshooting

This section provides solutions to common problems you might encounter with your disc brake system.

ProblemPossible CausesSolution
Friction between brake block and discIncorrect adjustment of brake block or caliper body; Disc deformation or bendingReadjust the brake block or caliper body (refer to Chapter 3); Replace the disc (refer to Chapter 2)
Poor gripAir exists in the system; Insufficient brake oilLoosen oil groove sealing screw and press handle to exhaust air; Replenish brake oil (refer to Chapter 5)
Transfer seat is looseLoose fixing screws of the adapterLock the fixing screws of the adapter (refer to Chapter 2)
Disc brake handle can be pressed to the driver's handleInsufficient brake oilReplenish brake oil (refer to Chapter 5)
Oil leakageDamaged components or improper sealingCheck the oil leakage part and repair or replace as needed
Insufficient or no braking forceBrake block is polluted or contaminated; Contaminated or oily discsThoroughly clean and dry the discs with a clean cloth dipped in alcohol, and replace the brake block.

7. User Tips

  • Regularly check brake fluid levels and top up as needed to maintain consistent braking performance.
  • Ensure all connections are tight but do not overtighten, as this can damage components.
  • For optimal performance, use only genuine ZOOM replacement parts and mineral oil.
  • If you experience any unusual noises or reduced braking power, stop riding and inspect the brake system immediately.

8. Warranty and Support

The effective shelf-life period of this product is one year from the date of purchase. This warranty covers manufacturing defects under normal use conditions.

For technical support, warranty claims, or service inquiries, please contact your retailer or the official ZOOM service center. Keep your proof of purchase for warranty validation.

Please refer to the official user manual PDF for additional details: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.