GTMEDIA V8 Finder Pro 2

Contents

GTMEDIA V8 Finder Pro 2 Satellite Signal Finder User Manual

Model: V8 Finder Pro 2

Important Safety Instructions

Thank you for choosing our product. Before installation, we would like to remind you of some notes, which are very important for operating safely and properly, as follows:

  • Be sure to read this user manual before starting your operation.
  • You must install the dish with correct direction and angle. If the dish is not working properly, contact your local dealer.
  • When the unit is suddenly moved to a hot area from a cold area, it may cause some problems. In that case, turn off the power, and turn on again after 1-2 hours.
  • Keep meter placed in clean space with sufficient ventilation.
  • Do not cover the meter with or place it on a unit that emits heat.
  • Clean the case by a soft cloth with a little washing liquid.
  • Do not remove the cover.
  • Do not let the unit exposed to extreme heat, cold or humid conditions.
  • No liquids or any other materials to come inside of the unit.

Product Overview & Illustration

The GTMEDIA V8 Finder Pro 2 is a versatile digital signal finder designed for DVB-S2X/S2/S/T2/T/C/ATSC-C signals. It features a 4.3-inch HD LCD, a 4000mAh battery, and supports H.265 video decoding.

GTMEDIA V8 Finder Pro 2 with key features highlighted
Figure 1: GTMEDIA V8 Finder Pro 2 highlighting DVB-S2X/S2/S/T2/T/C compatibility, H.264/H.265 (8 bit), MPEG-2/MPEG-4 support, and 2-year warranty.
Front view of the GTMEDIA V8 Finder Pro 2
Figure 2: Front view of the GTMEDIA V8 Finder Pro 2, showing the display and control buttons.

Product Components

Package contents of GTMEDIA V8 Finder Pro 2
Figure 3: Package contents including the V8 Finder Pro 2 device, user manual, product warranty card, power adapter, and AV cable.

Device Layout and Functions

Diagram showing signal strength measurement with a satellite dish and the V8 Finder Pro 2
Figure 4: Diagram illustrating signal strength measurement using the V8 Finder Pro 2, showing a satellite dish receiving signals and the device displaying signal quality and strength.

The following table details the various parts and their functions:

No. Description Function
1LCD ScreenVideo display
2Battery level displayIndicates remaining battery power in 5 levels.
3PowerPower indicator light
422KHz22kHz indicator light
513V/18VVertical/Horizontal polarization voltage output light
6LockSignal Lock indicator light
7Charger (Note1)Charger indicator light (red for charging, blue for full)
8DVBDVB mode switch for LCD
9AHDAHD IN mode switch for LCD
10AV INAV IN mode switch for LCD
11LCDTurn on and off the screen backlight
12Red & RECRed Key & Enter record function
13Green & SUBTGreen key & subtitle interface
14Yellow & TEXTYellow key & Teletext interface
15Blue & EPGBlue key & EPG interface
16MENUShow the main menu on the screen or jump back to previous menu in sub-menu setting conditions
17EXITEscape from present menu and save the settings
18LOOPLOOP Search interface
19SPECSpectrum interface
20Navigation KeyVolume Control or move cursor, channel or change, confirm etc.
210-9Number key to select channels or enter programming
22TV/RTV and radio switch
23AUDIOAudio interface
24SATDisplay the satellite list
25INFOInfo interface
26MUTEEnable or disable the audio output
27LNB INConnect to satellite antenna cable
28ANT INConnect to antenna of DVB-T/T2/C signal
29AHDConnect the analog AHD cable to the LCD screen
30USBConnect to USB memory or USB WIFI
31DC InputConnect to adaptor input (9V/2A)
32Power SwitchTurn on/off meter
33HDMIUse HDMI cable to connect for TV
34DC12V OUTConnect to AHD power supply (1Ah MAX)
35AV INConnect to AV port for meter
36SpeakerSpeaker integrated

Note on Battery Indicator: Battery indicator lights up when using the unit on batteries. The remaining battery power is displayed in 5 levels. When the battery is low and the warning message is flashing, please connect the USB charger to charge the lithium battery.

Setup

Initial Connections

Before powering on the device, ensure all necessary cables are connected securely. Refer to the diagram below for typical connections.

Wiring diagram for GTMEDIA V8 Finder Pro 2 connecting to TV, AC/DC adapter, antenna, and AHD camera
Figure 5: Connection diagram showing the V8 Finder Pro 2 connected to a television via HDMI, an AC/DC adapter for power, an antenna for signal input, and an AHD camera for monitoring.
  1. Connect the AC/DC Adapter to the device's DC Input (31) and a power outlet to charge the device.
  2. For satellite signal reception, connect the satellite antenna cable to the LNB IN port (27).
  3. For terrestrial or cable signals, connect the antenna cable to the ANT IN port (28).
  4. If using an AHD camera, connect the AHD cable to the AHD port (29).
  5. To view the signal on a larger screen, connect an HDMI cable from the device's HDMI port (33) to your TV.
  6. To connect to USB memory or USB WIFI, use the USB port (30).

Power On and Basic Settings

  1. Ensure the device is charged or connected to power.
  2. Turn on the device using the Power Switch (32).
  3. Once powered on, the main menu will appear.
  4. Navigate to "System Setting" using the Navigation Key (20) and press OK.
  5. In System Settings, you can adjust:
    • Language: Change the system default language.
    • TV System: Switch TV system (Auto/PAL/NTSC).
    • Beeper: Enable or disable the beep tone for lock alarm.
    • WiFi Manager: Set WiFi connection settings (for 2.4G WiFi).
    • Local Longitude/Latitude: Set your geographical coordinates for accurate satellite angle calculations.

For a visual guide on basic operations and menu navigation, please watch the product video:

Video 1: GTMEDIA V8 Finder Pro 2 product demonstration, showcasing device features and menu navigation.

Operating Instructions

After connecting the necessary cables and powering on the device, press the MENU button (16) to display the Main Menu.

Main Menu Navigation

The main menu provides access to various functions:

  • Satellite: For DVB-S/S2/S2X signal search and setup.
  • Terrestrial: For DVB-T/T2 signal search and setup.
  • Cable: For DVB-C signal search and setup.
  • Spectrum: To view signal spectrum.
  • Loop Search: For specific channel loop searches.
  • Calculate: To calculate satellite dish angles.
  • Other: Access to Media Player, USB Upgrade, Factory Setting, and Information.
  • System Setting: For device configuration (language, TV system, WiFi, etc.).

1. Terrestrial (DVB-T2) Scan

  1. From the Main Menu, select "Terrestrial" and press OK.
  2. In the DVB-T2 scan setup, adjust the following parameters:
    • Country: Change the default country.
    • Frequency Channel: Change the channel number.
    • Frequency (KHz): Input the frequency of the current channel using the number keys.
    • Bandwidth: Change the bandwidth (6, 7, or 8M).
    • Antenna Power: Turn the antenna power on or off.
    • LCN: Turn the Logical Channel Number (LCN) on or off.
  3. Press the Blue key to "Scan" the current channel.
  4. Press the Yellow key to "Auto Search" for channels.

2. Satellite (DVB-S2X) Find

  1. From the Main Menu, select "Satellite" and press OK to enter the Satellite Find menu.
  2. Select the desired satellite from the list.
  3. Adjust parameters as needed:
    • LNB Freq: Select the appropriate LNB frequency.
    • Frequency Channel: Select the Transponder (TP) you want.
    • Frequency / Symbol Rate: Input the values for the current transponder using the number keys.
    • Polarity: Change between vertical or horizontal polarization.
    • DiSEqC1.0 / DiSEqC1.1: Set the port number for DiSEqC switches.
    • 22K: Turn on or off the 22 kHz switch.
    • Motor Setup: If using DiSEqC1.2 or USALS, select IF Channel and input Center Frequency.
  4. Press the Yellow key for "TP Search" to find the current TP.
  5. Press the Blue key for "Blind Scan" to search the entire satellite.

3. Cable (DVB-C) Scan

  1. From the Main Menu, select "Cable" and press OK to enter the DVB-C scan setup.
  2. Adjust parameters such as Frequency, Symbol Rate, and Modulation.
  3. Press the Blue key to "Scan" for the current channel.
  4. Press the Yellow key to enter the "Range Search" setting interface for a broader scan.

4. Calculate Satellite Pot Angle

  1. From the Main Menu, select "Calculate" and press OK.
  2. If you have set the Longitude and Latitude under "System Setting", the angle of LNB, the orientation, and elevation of the antenna will be displayed on the screen. This helps in precise dish alignment.

5. View Spectrum

  1. From the Main Menu, select "Spectrum" and press OK.
  2. This feature allows you to visualize the signal strength across different frequencies, aiding in fine-tuning your antenna or dish.

Maintenance

  • Cleaning: Clean the device case with a soft cloth and a small amount of washing liquid. Do not use harsh chemicals or abrasive materials.
  • Ventilation: Ensure the meter is placed in a clean space with sufficient ventilation to prevent overheating. Do not cover the meter or place it near heat-emitting units.
  • Environmental Conditions: Avoid exposing the unit to extreme heat, cold, or humid conditions.
  • Liquid and Foreign Objects: Prevent any liquids or other materials from entering the unit.
  • Internal Access: Do not attempt to remove the cover or access internal components, as this may void the warranty and cause damage.

Troubleshooting

  • Device Malfunction After Temperature Change: If the unit malfunctions after being moved from a cold to a hot area, turn off the power and wait 1-2 hours before turning it on again. This allows the device to acclimatize.
  • No Signal/Weak Signal:
    • Check all cable connections (LNB IN, ANT IN) to ensure they are secure.
    • Verify that the LNB frequency, transponder frequency, symbol rate, and polarity settings are correct for your satellite.
    • Ensure the antenna or dish is correctly aligned and free from obstructions.
    • Check if the LNB power is enabled in the settings if required.
  • Software Issues/Device Not Booting:
    • If performing a USB upgrade, ensure the power is not turned off and the USB is not pulled out during the process. Interrupting an upgrade can damage the software and prevent booting.
    • If issues persist, consider performing a "Factory Setting" reset (see "Other Functions" in Operating Instructions). Note that this will erase all user settings and the database.
  • Compass Inaccuracy: If the built-in compass appears inaccurate, ensure there are no magnetic interferences nearby. Some protective cases might also interfere with its operation.

Specifications

Feature Detail
Brand NameGTMEDIA
Model NumberV8 Finder Pro 2
TypeDIGITAL, Sat Finder
High DefinitionYes
FTA(Free To Air)Yes
CertificationCE
OriginMainland China
Display4.3 inch HD LCD
Battery4000mAh Large capacity
DC Input9V/2.5A
Power Consumption10W Max
Charging9V fast charging
WIFI2.4G
Weight0.6KG
Size123x204x45mm
Supported StandardsDVB-S2X/S2/S/T2/T/C/ATSC-C
Video DecodingH.264/H.265 (8 bit), MPEG-2/MPEG-4
Language SupportPolski, Indonesia, Portugues, Russian, French, Spanish, English, Italian, Turkish, Arabic, Farsi etc

Warranty & Support

The GTMEDIA V8 Finder Pro 2 comes with a 2-year warranty from the date of purchase, covering manufacturing defects.

For more product feature introduction, user guides, software updates, or technical support, please visit the official forum and YouTube channel:

A detailed user manual in PDF format is also available for download. Please refer to the official website for the latest version.

Manufacturer Information:
Shenzhen GTMEDIA Technology Co., Ltd
Address: 601A, comprehensive building, Nankeng second industrial zone, Nankeng community, Bantian street, Longgang District Shenzhen, 518000, Guangdong, CN

European Company: GTMAX TECHNOLOGY, S.L.
Address: C. DEL PUERTO DE POZAZAL, 4, NAVE 32,28031 MADRID, ESPAÑA

User Tips

  • Initial Setup: The device is generally straightforward to use for initial signal finding tasks.
  • Frequency Setup: For specific regions, such as Korea, you may need to manually set up frequencies if they are not pre-programmed.
  • Compass Usage: Be aware that some protective cases might obstruct or interfere with the built-in compass. For accurate readings, ensure the compass is unobstructed and away from magnetic interference.

Frequently Asked Questions (FAQ)

Q: What is the primary use of the GTMEDIA V8 Finder Pro 2?
A: It is primarily used as a digital signal finder for various broadcast standards including DVB-S2X/S2/S (satellite), DVB-T2/T (terrestrial), and DVB-C (cable), helping users to accurately align antennas and satellite dishes.
Q: Does the device support HD channels?
A: Yes, the GTMEDIA V8 Finder Pro 2 supports High Definition (HD) signals and features a 4.3-inch HD LCD for clear viewing.
Q: Can I update the software on this device?
A: Yes, the device supports USB upgrades. You can download the latest software from the official website (www.freesat.cn) and update it via the USB port.
Q: What should I do if the device malfunctions after being moved from a cold to a hot environment?
A: Turn off the power and allow the unit to sit for 1-2 hours to acclimatize to the new temperature before turning it back on.
Q: How do I reset the device to factory settings?
A: Navigate to the "Other" menu, then select "Factory Setting" and confirm. Be aware that this action will erase all your personalized settings and stored data.
Q: How do I know if the device is fully charged?
A: When the AC/DC adapter is connected, the charging indicator light will be red during charging and turn blue when the battery is full.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.