1. Introduction
Thank you for purchasing the Baofeng UV-25M Ham Radio. This dual-band, dual-display, dual-watch radio is designed to provide secure, instant, and reliable communications. Please read this manual carefully to ensure maximum performance and safe operation of your device.
1.1 Main Features
- Frequency Range: FM radio 65-108 MHz; 136-174MHz (RX); 220-260MHz (RX); 400-520MHz (RX); 144-148MHz (TX); 220-260MHZ (TX); 420-450MHz (TX)
- Output Power: 10W-25W
- Channels: Up to 999 memory channels
- Display: 1.77" TFT large color screen, full keyboard, fully open menu operation
- Charging: Type-C USB Charger for portable charging (car charger, power bank, direct charge)
- Scanning: Channel scan, frequency scan, CTCSS scanning, DCS scanning, NOAA weather scan
- Functions: One touch search frequency, easy pairing and grouping, frequency step selection (2.5K, 5.0K, 6.25K, 10.0K, 12.5K, 20.0K, 25.0K, 50.0K), frequency hopping, power-on password management, DTMF encoder and manual dial, VOX (voice activated transmit), alarm function, high/low power selectable, programmable repeater offset, transmission time-out timer, 10 levels of Squelch adjustment, End of transmission tone ("Roger Beep"), Dual watch / Dual reception, Stopwatch function, Display illumination programmable, Function beep, Battery save function, Busy channel lock out.
- Accessory Port: Two (2) pins for Kenwood accessory port
- Battery: High Capacity Lithium-Ion battery (2800mAh)

1.2 Package Contents
The standard package includes:
- 1 x Radio Unit
- 1 x Li-ion Battery Pack
- 1 x Fast Charger
- 1 x Antenna
- 1 x Belt Clip (not explicitly listed in OCR, but common accessory)
- 1 x Hand Strap (not explicitly listed in OCR, but common accessory)
- 1 x User Manual (PDF reference)
Please check all items upon unpacking. If any item is missing or damaged, contact your dealer.
2. Safety Warnings and Regulations
2.1 General Safety Instructions
- Do not operate the product in locations containing fuels, chemicals, explosive atmospheres, or other flammable/explosive materials.
- Do not operate near blasting areas or medical/electronic equipment vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate where wireless communication equipment is prohibited.
- Do not use any unauthorized or damaged accessory.
- Keep the product at least 2.5 cm away from your body during transmission.
- Avoid prolonged high-volume reception.
- Do not place the product in the air bag deployment area in vehicles.
- Keep the product and accessories out of reach of children and pets.
- Operate within the specified temperature range.
- Continuous transmission may lead to heat accumulation; allow for cooling.
- Handle with care; do not disassemble, modify, or repair without authorization.
2.2 RF Energy Exposure and Compliance
WARNING! Operation of this unit in Transmit mode requires a valid Amateur Radio License in Europe (refer to EU specification guide 2014/53/EU) and compliance with FCC/IC regulations in North America. Failure to comply may be unlawful.
This device complies with FCC Part 15 and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Precautions:
- Do not use the radio with a damaged antenna.
- For hand-held operation, hold the radio 1 inch (2.5 cm) from the front of your face.
- For body-worn operation, use only supplied belt-clip accessories to ensure compliance with RF exposure guidelines. Avoid third-party accessories unless approved by the manufacturer.
PMR446, FRS, GMRS, MURS: This transceiver may be illegal for use on PMR446 (Europe) or FRS, GMRS, MURS (USA) frequencies due to specific restrictions on these bands.
3. Setup and Installation
3.1 Charging the Battery
The Li-ion battery pack is not charged at the factory and must be charged before first use. For best performance, fully charge and discharge the battery two or three times.

Charging Procedure:
- Plug the AC adaptor into an AC outlet, then connect its cable to the DC jack on the back of the charger. The indicator light blinks orange.
- Plug the battery (or the radio with battery installed) into the charger. Ensure good contact with charging terminals. The indicator light turns red.
- Charging takes approximately 2-5 hours. The lamp turns green when charging is complete.
- If charging the radio with the battery installed, ensure the radio is OFF for the charger to correctly indicate full charge.
LED Indicator Status:
| Status | LED Indication |
|---|---|
| No Battery | Green and red alternately flashing |
| Charge Normally | Red |
| Fully Charged | Green |
| Trouble (e.g., battery too warm, short-circuited) | Red blinks fast for a long time |
Battery Precautions:
- Do not charge or replace the battery in locations with fuels, chemicals, or explosive materials.
- Do not charge a wet battery; dry it first.
- Do not charge deformed, leaking, or overheated batteries.
- Use only authorized chargers.
- Avoid charging in areas with strong radiation.
- Do not expose to direct sunlight or other heating sources.
- Do not squeeze, penetrate, or remove the battery housing.
- For storage, keep the battery 80% discharged in a cool, dry environment.
3.2 Installing/Removing the Antenna
- Installing: Screw the antenna into the connector on top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
- Removing: Turn the antenna counter-clockwise.

3.3 Installing the Belt Clip and Battery Pack
Align the belt clip with the designated slots on the back of the radio and secure it with screws. To install the battery pack, align it with the battery compartment and slide it into place until it clicks securely. To remove, press the release latch and slide the battery out.
3.4 Accessory Jack
The accessory jack on the Baofeng UV-25M is a Kenwood-compatible two (2)-pin design. It is used for connecting accessories such as headsets, speaker-mics, or programming cables.
Accessory Jack Diagram:
Speaker
|
|----(o)----
| |
| |----(o)---- 02.5mm
| |
| |----(o)---- 12mm
| |
| |----(o)---- 03.5mm
|
|----(o)---- Mic
|
|----(o)---- PTT
|
|----(o)---- +5V
|
|----(o)---- 10µF
- Align connectors and push in fully. Some cables may require force.
- Ensure the radio is OFF before attaching any accessories.
4. Radio Overview and Controls
4.1 Buttons and Controls

Key Components:
- Antenna
- Status LED
- SK1- Weather and search frequency key
- PTT key (Push-to-Talk)
- SK2- Broadcast FM/Monitor key
- SK3- Flashlight and Alarm key
- Up/Down navigation keys
- MENU key (Menu and VFO/MR mode key)
- Numeric keypad
- Power/Volume knob
- Speaker
- Microphone (MIC Input)
- Color LCD
- EXIT/A/B select key
- LED Flashlight
- Accessory jack
- Type-C charging port
- Type-C charging indicator
4.2 LCD Display Icons
| Icon | Description |
|---|---|
| RSSI | Squelch Open/Close Indicator |
| H/L | Transmit power level indicator (High/Low) |
| ♪ | DTMF side tone enabled |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Repeater access: TX shifted higher than RX |
| - | Repeater access: TX shifted lower than RX |
| D | Dual watch enabled |
| 🔒 | Keypad lock enabled |
| VOX | VOX enabled |
| Confidential calling | Confidential calling feature activated |
| N | Narrowband enabled |
| 🔋 | Battery level indicator |
| R | Reverse function enabled |
| ► | Indicates active band or channel |
When the battery level indicator (🔋) shows low, the radio will beep periodically and flash the backlight. A "Low Voltage" announcement will be heard if voice prompts are enabled, indicating it's time to charge.
4.3 Status LED Indications
| LED Indicator | Radio Status |
|---|---|
| Constant Red | Transmitting |
| Constant Green | Receiving |
4.4 Main Keypad Controls
- Side Key 1 (SK1): Momentary press for NOAA scan. Press and hold for frequency search.
- Side Key 2 (SK2): Momentary press to turn Broadcast FM receiver ON/OFF. Press and hold to monitor (open squelch).
- Side Key 3 (SK3): Momentary press to turn LED flashlight ON/OFF (flashing with second press). Press and hold for alarm function.
- MENU Key: Activates the MENU, selects menu items, confirms parameters. Press and hold to switch between Frequency (VFO) and Channel (MR) mode.
- Up (▲) / Down (▼) Keys: Navigate channels/frequencies. Press and hold for rapid movement. In SCAN mode, moves scanning direction.
- EXIT/A/B Key: Exits Menu and functions. Selects desired frequency (VHF or UHF) in main or secondary display. Press and hold to activate one-touch search.
- Star (*) Key: Short press enables reverse function. Press and hold for 2 seconds to lock/unlock keypad.
- Pound (#) Key: Press to activate DTMF dial function. Press and hold to activate channel scan or frequency scan. In FM radio mode, press to automatically search for broadcast programs.
5. Basic Operations
5.1 Power On/Off
- To Turn On: Rotate the Volume/Power knob clockwise until you hear a "click". The radio will emit a double beep, display a message or flash the LCD, then show a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".
- To Turn Off: Rotate the Volume/Power knob counter-clockwise until you hear a "click".
5.2 Adjusting the Volume
Rotate the Volume/Power knob clockwise to increase volume, counter-clockwise to decrease. Use the monitor function (SK2 press and hold) to adjust volume against un-squelched static for easier setting.
5.3 Main Band/Sub Band Select
In standby mode, press the EXIT/A/B key to switch between the A (upper) and B (lower) displays. The selected display becomes the active listening and transmit frequency or channel. Frequencies must be saved to channel memory from the A display.
5.4 VFO/Channel Switch
Press and hold the MENU key to switch between VFO (Frequency) and Channel (MR) mode. In Channel mode, the channel number is displayed. In Frequency mode, 'VFO' is displayed.
5.5 Frequency (VFO) Mode
In VFO mode, use the Up/Down keys to navigate frequencies according to the set frequency step. You can also directly input frequencies using the numeric keypad with kilohertz accuracy.
Example: Entering 436.61250 MHz on display A
- In standby mode, press and hold the MENU key to switch to VFO mode.
- Enter [4][3][6][6][1][2][5][0] on the numeric keypad.
WARNING: Transmitting on unauthorized frequencies is illegal and can result in serious penalties.
5.6 Channel (MR) Mode and Channel Selection
Channel (MR) mode is practical for everyday use with preprogrammed channels. VFO mode is used for experimentation and programming channels.
To switch to Channel mode, press and hold the MENU key. Navigate channels using the Up/Down keys or by directly inputting channel numbers (e.g., [0][1][2] for channel 12).
5.7 Making a Call
- Channel Mode Call: Select a channel, then hold down the PTT key to transmit. Speak into the microphone with a normal tone. The red LED will illuminate.
- Frequency Mode Call: Switch to VFO mode, input the desired frequency, then hold down the PTT key to transmit. The red LED will illuminate.
- Receiving a Call: Release the PTT key. The green LED will illuminate when receiving.
For best reception, maintain a distance of 2.5 cm to 5 cm between the microphone and your mouth during transmission.
5.8 Emergency Alert
To activate, press and hold the SK3 key for 3 seconds. The radio will emit a siren sound and the flashlight will flash. Press SK3 again to exit. Use only in actual emergencies.
5.9 FM Radio (FM)
The radio can receive FM broadcasts from 65-108 MHz.
- In frequency or channel mode, press SK2 to turn on the FM radio.
- Select the desired frequency using Up/Down keys or numeric keypad. Press the # key to automatically search for stations.
- Press SK2 to exit FM radio.
If a signal is received on the active A/B receiving signal, the radio will temporarily switch to that frequency/channel for transmission/reception, then return to FM radio mode when the signal disappears.
5.10 Monitor
In standby, press and hold SK2 to enter Monitor mode. This allows you to hear weak signals or signals with matched carriers but no signaling. Release SK2 to exit.
5.11 Keypad Lock
To enable/disable, press and hold the Star (*) key for about two seconds. The radio can also be set to automatically lock the keypad after 10 seconds of inactivity via the menu.
5.12 Frequency Reversal
A short momentary press of the Star (*) key enables the reverse function, swapping transmit and receive frequencies. An 'R' will appear on the screen. This is useful for listening to a repeater's input frequency.
5.13 TX Repeaters Tone
Press PTT + SK3 to send a 1750Hz repeater tone. This is used to open up certain amateur radio repeaters. This function works even if the keypad is locked.
5.14 One Touch Frequency Search
The radio acts as a receiver to search for active frequencies.
- Press and hold SK1. The screen will display "SEARCH SEARCH...".
- When a stable signal is received, the frequency will be displayed. If CTCSS or DCS is present, it will also be shown.
- Press MENU to save the found frequency and CTCSS/DCS to a channel.
During search, press # to switch between UHF or VHF bands.
5.15 Weather Radio/Scan Weather Channel
The radio supports NOAA Weather Radio for receiving weather reports and NOAA Weather Scan for scanning all 10 NOAA channels.
- To turn on NOAA Weather Scan, press SK1. A weather icon will appear, and the radio enters Weather band mode.
- Press and hold the # key for 3 seconds to start automatic scanning of all 10 channels, stopping on active ones. Press and hold # again to stop the scan.
- To manually select a weather channel, use the Up/Down keys.
- To exit Weather Radio broadcast mode, press MENU or PTT.
NOAA Weather Channel Frequencies:
| Channel Number | RX Frequency MHz | Channel Number | RX Frequency MHz |
|---|---|---|---|
| Wx-01 | 162.550 | Wx-06 | 162.500 |
| Wx-02 | 162.400 | Wx-07 | 162.525 |
| Wx-03 | 162.475 | Wx-08 | 161.650 |
| Wx-04 | 162.425 | Wx-09 | 161.775 |
| Wx-05 | 162.450 | Wx-10 | 163.275 |
These are Receive-only channels for NOAA and Canadian weather broadcasts; transmission is not possible.
6. Advanced Features and Menu System
The radio's menu system allows access to various advanced features and customization options. If the radio is in Memory (MR) mode, certain menu items (STEP, TXP, W/N, CTCSS, DCS, S-CODE, PTT-ID, BCL, SFT-D, OFFSET, MEM-CH) will not take effect.
6.1 Working the Menu System
Basic Use:
- Press MENU to enter the menu.
- Use Up/Down keys to navigate menu items.
- Press MENU to select a menu item.
- Use Up/Down keys to select the desired parameter.
- Press MENU to confirm and save, returning to the main menu.
- To cancel changes and exit, press EXIT/A/B.
Using Shortcuts: Each menu item has a numerical value for direct access.
- Press MENU.
- Enter the numerical menu item using the keypad.
- Press MENU to enter the item.
- Enter the numerical shortcut code for the parameter or use Up/Down keys.
- Press MENU to confirm and save.
- Press EXIT/A/B to exit the menu.
6.2 Scanning
The radio features a built-in scanner for VHF and UHF bands. In VFO mode, it scans according to the set frequency step. In Channel (MR) mode, it scans your programmed channels. To enable the scanner, press and hold the # key for about two seconds. Press and hold # again to exit scanning mode. Dual Watch is inhibited during scanning.
Scanning Modes (Menu 21):
- Time Operation (TO): Scanner stops on a signal, then resumes after a preset time.
- Carrier Operation (CO): Scanner stops on a signal, then resumes after a preset time with no signal.
- Search Operation (SE): Scanner stops on a signal and waits for manual resume (press #).
Frequency Scanning: In VFO mode, press and hold # for 2 seconds. Change direction with Up/Down keys. Press # to stop.
Channel Scanning: In Channel mode, press and hold # for 2 seconds. Change direction with Up/Down keys. Press # to stop.
CTCSS Scanning (Menu 14): In standby, press MENU, then [1][4]. Press MENU to start scanning for CTCSS tones. (Not available in Channel mode).
DCS Scanning (Menu 15): In standby, press MENU, then [1][5]. Press MENU to start scanning for DCS codes. (Not available in Channel mode).
6.3 Manual Programming (Channels Memory)
The radio has 999 memory channels. Each channel can store receive/transmit frequencies, transmit power, signaling info, bandwidth, ANI/PTT-ID settings, and a 6-character alphanumeric identifier.
Programming a Channel Repeater Offset with CTCSS Tone (Example):
- Press MENU to switch between menus.
- Press and hold MENU to set the radio to VFO mode.
- Navigate to the desired channel (e.g., Menu 3, 1, 1 for channel 10).
- Select TX encode tone (e.g., Menu 1, 2 for 123.0 CTCSS).
- Enter RX frequency (e.g., 432.55000 MHz).
- Enter TX frequency (e.g., 437.55000 MHz).
- Press and hold MENU to return to MR mode.
Programming a Simplex Channel with CTCSS Tone (Example):
- Press MENU to switch between menus.
- Press and hold MENU to set the radio to VFO mode.
- Select TX encode tone (e.g., Menu 1, 2 for 123.0 CTCSS).
- Enter RX frequency (e.g., 432.6625 MHz).
- Press and hold MENU to return to MR mode.
6.4 Repeaters Programming
This assumes you know the repeater's transmit/receive frequencies and are authorized to use it.
- Press and hold MENU to set the radio to VFO mode.
- Enter the repeater's output (your receiving) frequency using the numeric keypad.
- Press MENU to enter the menu.
- Enter [2][9] for frequency offset. Press MENU to select.
- Enter the specified frequency offset using the keypad. Press MENU to confirm.
- Enter [2][8] for offset direction. Press MENU to select.
- Use Up/Down keys to select + (positive) or - (negative) offset. Press MENU to confirm.
- (Optional) Save to memory (see Manual Programming) and/or set up CTCSS.
- Press EXIT/A/B to exit the menu.
6.5 VOX (Voice Activated Transmit)
Enables hands-free conversations. Speak into the microphone to activate transmission. In standby mode, press MENU + 7. Press MENU to enter. Use Up/Down keys to turn VOX ON/OFF or select level (1-10). Press MENU to confirm. Level 1 is least sensitive, 10 is most. VOX is not enabled in Scan or FM Radio mode.
6.6 Dual Watch
Allows monitoring two channels simultaneously. The display will show activity from either channel. To enable/disable, press MENU + 44. Press MENU to enter. Use Up/Down keys to turn ON/OFF. Press MENU to confirm.
6.7 Stopwatch Timer
In standby mode, press MENU + 44. The screen displays "STOP WATCH". Press MENU to enter. Use Up/Down keys to enable (ON). Press MENU to confirm. When ON, press MENU to start/restart counting. To exit, stop counting then press EXIT/A/B.
6.8 DTMF (Dual-Tone Multi-Frequency)
Used for automation systems and remote control, commonly in amateur radio repeaters. The radio fully implements DTMF A, B, C, D codes. Numeric keys correspond to DTMF codes. A, B, C, D codes are located on the Up, Down, Star (*), and Pound (#) keys respectively. To send DTMF codes, press the desired key(s) while holding down the PTT key. This works even with keypad lock enabled.
DTMF Frequencies and Codes:
| 1209Hz | 1336Hz | 1477Hz | 1633Hz | |
|---|---|---|---|---|
| 697Hz | 1 | 2 | 3 | A |
| 770Hz | 4 | 5 | 6 | B |
| 852Hz | 7 | 8 | 9 | C |
| 941Hz | * | 0 | # | D |
6.9 Customization Options
- Display Backlight (ABR) - Menu 7: Set backlight duration (ON/5/10/15/20 seconds).
- Beep Prompt (BEEP) - Menu 8: Enable/disable key press beep tone.
- Voice Function (VOICE) - Menu 17: Enable/disable voice prompts.
- Language of the MENU (LANGUAGE) - Menu 18: Select English or Chinese.
- Working Mode (MDF-A) - Menu 24: Choose display mode (Frequency, Channel, or Channel Name).
- Roger Beep (ROGER) - Menu 36: Enable/disable end-of-transmission tone.
- Power On Message (POWER ON MSG) - Menu 40: Customize welcome message (VOLTAGE, MESSAGE, LOGO, MODEL NAME).
- Power On Password (POWER ON PWD) - Menu 43: Enable/disable password requirement at startup.
6.10 Reset - Menu 42
Two reset modes are available:
- Reset VFO: Resets all settings except channels to default.
- Reset ALL: Resets all settings to default.
To perform a reset, press MENU + 42. Use Up/Down keys to select VFO or ALL, then press MENU to confirm. Confirm again when prompted "Sure to reset?". The transceiver will turn off and reboot.
7. Troubleshooting Guide
| Phenomenon | Analysis | Solution |
|---|---|---|
| Cannot turn on the radio | Battery improperly installed, power run out, poor battery contact | Remove/reattach battery, recharge/replace battery, clean battery contacts |
| Weak or intermittent voice during reception | Low volume, loose/incorrect antenna, blocked speaker | Increase volume, reattach antenna, clean speaker surface |
| Cannot communicate with other group members | Inconsistent frequency/signaling type, too far from members | Verify TX/RX frequency and signaling, move closer |
| Hear unknown voices or noise | Interrupted by other radios, analog mode with no signaling, too far from members | Change frequency/squelch level, request dealer to set signaling, move closer |
| Unable to hear due to too much noise/hiss | Unfavorable position (blocked by buildings), external disturbance | Move to open/flat area, restart radio, avoid interference sources |
| Radio keeps transmitting | VOX turned on, headset not installed correctly | Turn off VOX, check headset connection |
If these solutions do not resolve your issues, please contact your dealer for technical support.
8. Technical Specifications
| Feature | Specification |
|---|---|
| Frequency Range | 136-174MHz (Rx), 220-260MHz (Rx), 400-520 MHz (Rx), FM65-108MHz (Rx) |
| Channel Spacing | 25.0KHz (Wide) / 12.5KHz (Narrow) |
| Memory Channels | 999 Groups |
| Operation Voltage | DC 7.4 V ±10% |
| Transmission Current | ≤2800mA |
| Receive Sensitivity | 0.25µV (12dB SINAD) |
| Rated Audio Power Output | 1W @16 ohms |
| Receive Current | ≤380mA |
| Connection for Accessories | 2 pin Kenwood jack |
| Antenna Impedance | 50 Ohm |
| Output Power (w) | 10w-25w |
| Battery Capacity (mAh) | 2800 |
| Waterproof / Water-Resistant | No |
| Battery Included | Yes |
| Material | Plastic |
| Dimensions | 180mm*65mm*40mm (Antenna Not included) |
| Walkie Talkie Type | Portable |
| Is_Display | No (This contradicts the 1.77" TFT display feature, likely refers to a specific display type or external display capability. The radio does have an internal display.) |
| Maximum Range | 10km-50km |
| Origin | Mainland China |
| Certification | CE, FCC |
Note: All specifications are subject to modification without prior notice or liability.
9. User Tips
- Initial Charge: Always perform a full charge-discharge cycle two to three times for new batteries to optimize battery life and performance.
- Programming Software: For advanced customization and channel management, consider using the official programming software with a compatible cable. This allows for easier setup of complex repeater settings and channel names.
- Antenna Choice: Experiment with different antennas, such as the included goose tube antenna or other compatible options, to find the best performance for your specific operating environment and frequency bands.
- Power Management: Utilize the 'Battery Save' function (Menu 3) to extend battery life, especially during long periods of monitoring.
- Keypad Lock: Enable the automatic keypad lock (Menu 27) to prevent accidental button presses during transport or when carrying the radio.
- Voice Prompts: If you find the voice prompts distracting, they can be disabled via Menu 17 (VOICE).
10. Warranty and Support
10.1 Disclaimer
The manufacturer endeavors to ensure the accuracy and completeness of this manual. However, no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed without prior written consent from the manufacturer.
The manufacturer does not guarantee the accuracy, validity, timeliness, legitimacy, or completeness of third-party products and content referenced in this manual.
10.2 Product Support
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact your authorized dealer or the point of purchase. Unauthorized opening or modification of the transceiver will void the warranty.
User Manual (PDF) Reference: A detailed user manual in PDF format is available for further reference. View User Manual (PDF)