MOES SGW08

Contents

MOES Smart 2-Outlet Water Timer User Manual

Model: SGW08

1. Introduction

Thank you for choosing the MOES Smart 2-Outlet Water Timer. This device allows you to automate your garden irrigation with smart scheduling, rain delay functions, and remote control via the MOES app. This manual provides detailed instructions for setup, operation, and maintenance to ensure optimal performance.

2. Product Description

The MOES Smart 2-Outlet Water Timer is designed for outdoor use, featuring two independently controllable outlets. It connects directly to a standard hose faucet and can be managed through the MOES smartphone application via Bluetooth.

2.1. Components

  • Hose Faucet Connection: Top inlet for connecting to your outdoor faucet.
  • LED Light: Indicates device status and pairing mode.
  • ON/OFF Button: Manual control and used for pairing.
  • Outlet Fitting 3/4": Two threaded outlets for connecting garden hoses or irrigation lines.
MOES Smart 2-Outlet Water Timer connected to a faucet with app interface showing dual zone control.
Figure 1: MOES Smart 2-Outlet Water Timer with its main components and a view of the app interface.

2.2. Dimensions

Diagram showing the dimensions of the MOES Smart 2-Outlet Water Timer.
Figure 2: Dimensions of the water timer. Width: 116.2mm (4.5in), Depth: 38.6mm (1.5in), Height: 117mm (4.6in), Top Width: 55mm (2.1in), Side Depth: 26.2mm (1.0in).

3. Specifications

FeatureSpecification
ModelSGW08
Communications ProtocolBluetooth
Working Pressure0.05-0.8MPa (7.25-116 psi)
Working Temperature4.5°C-45°C (40.1°F-113°F)
Rain Delay Time1 day and up to 7 days
Waterproof RatingIP55
Power Supply2 x AA alkaline batteries
Frequency Band2.4GHz ISM band
TX Transmit Power<+10dBm
Control Type2-way separate control
Standby Time≥6 months
Transmission Distance15M (49.2ft) in open environment

4. Setup

4.1. Initial Water Timer Setup

  1. Insert Batteries:
    • Remove the battery tray on the back of the timer by sliding or pulling it out.
    • Insert two AA (1.5V) alkaline batteries.
    • Replace the tray securely.

    Note: Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.

  2. Install the Timer:
    • Connect the timer to an outdoor hose faucet. Ensure it is tightly attached to prevent leakage. Adding a rubber washer and thread seal tape may be necessary.

    Note: Do not place the timer in an underground valve box or anywhere your Bluetooth signal will be obstructed.

  3. Turn on Your Water:
    • The water must remain on for the timer to work properly.

4.2. App Preparation and Device Pairing

  1. Download MOES App:
    • Download the MOES App from your device's App Store. The MOES App is recommended for enhanced compatibility and features. (Tuya Smart/Smart Life App also works).
  2. Register or Log In:
    • Open the MOES App. Register for a new account or log in if you already have one.
  3. Add Device:
    • Ensure your Bluetooth gateway (if used for stable wireless control) is connected to the MOES App.
    • In the app, navigate to your gateway and click "Add new devices".
    • Enter Pairing Mode: Press and hold one of the ON/OFF buttons on the water timer for more than 6 seconds until both green LED lights flash quickly at the same time.
    • The app will discover the device. Wait for 10-120 seconds for the device to be added successfully.
    • Once added, you can edit the device name for easy identification, especially if you have multiple timers.
    MOES Smart 2-Outlet Water Timer being added to a Bluetooth Gateway in the app.
    Figure 3: Connecting the water timer to a Bluetooth Gateway for stable wireless control.

5. Operating Instructions

5.1. App Interface Overview

After successful pairing, you can control and monitor your water timer through the MOES App. The app interface provides access to:

  • Battery Life indicator
  • Settings and Weather information
  • Independent control for Zone 1 and Zone 2
  • Custom image for each zone
  • Manual watering function
  • Countdown and Work Time display
  • Scheduling options for each zone

5.2. Scheduling Watering

The app allows you to set up timed or cyclical watering schedules for each zone independently.

App interface showing options for Timed Watering Schedule and Cyclical Watering Schedule.
Figure 4: App options for setting Timed or Cyclical Watering Schedules.

5.3. Manual Watering

You can manually activate watering for testing equipment, running an extra cycle, or using the hose faucet without removing the timer.

  • In the app, click the manual watering icon to activate.
  • Set the desired "Work Time" for the manual watering duration. The remaining time will be displayed.

5.4. Stop Watering

To stop watering at any time (during manual or programmed watering), click the manual watering icon again. The icon will change to indicate no water droplets.

5.5. Rain Delay Function

The rain delay function allows you to postpone scheduled watering for 1 to 7 days, useful during rainy weather or when the ground is already wet.

  • In the app, access the Rain Delay feature.
  • Select the desired delay duration (1 to 7 days).

Note: The delay feature must be manually operated in the App to start.

App interface showing Rain Delay options from 1 to 7 days.
Figure 5: Setting a Rain Delay for up to 7 days.

6. Maintenance

6.1. Battery Replacement

Replace batteries when the low battery indicator appears in the app. Ensure the water timer is dry before replacing the power unit.

6.2. Filter Cleaning

The timer includes a filter to trap dirt particles. Clean the filter regularly and replace it if worn to ensure proper water flow and prevent blockages.

Diagram showing IP55 waterproof features, including reinforced nylon fiber and a rubber ring for battery protection.
Figure 6: IP55 Waterproof design, highlighting the reinforced material and rubber ring for battery protection.

7. Troubleshooting

  • No Water Flow: Ensure the main water supply is turned on. Check if the filter is clogged and clean it if necessary. Verify that the timer has sufficient battery power.
  • Weak Water Flow: If both zones are turned on simultaneously, the water flow to each zone will be reduced by half. Water flow may also differ between zones if one is turned on before the other.
  • Bluetooth Connection Issues: Ensure your device is within the effective transmission distance (up to 15M/49.2ft in open environments). Avoid placing the timer where the Bluetooth signal might be obstructed.
  • Timer Not Responding: Check battery levels and replace if low. Ensure the timer is within the operating temperature range.
  • Leakage: Ensure the timer is tightly attached to the faucet and hoses. Use a rubber washer and thread seal tape if needed.

8. User Tips

  • Scheduling Limitation: You can set only one program for a specific day; different programs for the same day are not supported.
  • Multiple Timers: When using multiple timers, ensure you give each a distinct name in the MOES App for easy identification and control.
  • Gateway for Stability: For more stable wireless control and remote access beyond Bluetooth range, consider adding a Bluetooth gateway.
  • Winterization: Do not use the timer when the air temperature is below 4.5°C (40°F). Remove the timer from the hose faucet and store it indoors to prevent potential frozen damage during cold weather.
  • Voice Control: This Bluetooth water timer does not support direct Alexa or Google voice control.

9. Warranty and Support

9.1. Warranty Instructions

Products are covered by a 24-month warranty, effective from the date of purchase by a retail customer. To exercise warranty rights, the purchaser must present a warranty card and proof of purchase (VAT invoice, financial receipt, or other document confirming the actual date of purchase).

If product quality problems occur within 24 months from the date of receipt, prepare the product and packaging and return it to the place of purchase for after-sales maintenance. If the product is damaged due to personal reasons, a maintenance fee may be charged.

The warranty does not cover:

  • Mechanical damage caused by user fault.
  • Damage caused by improper use of the product.
  • Products with removed warranty seals or serial numbers.
  • Repairs performed outside of authorized service.
  • Use of non-original parts and consumables.

9.2. Contact Information

Manufacturer: WENZHOU NOVA NEW ENERGY CO.,LTD
Address: Power Science and Technology Innovation Center, NO.238, Wei 11 Road, Yueqing Economic Development Zone, Yueqing, Zhejiang, China
Tel: +86-577-57186815
After-sale Service: service@moeshouse.com

10. Declaration of Conformity

Hereby, WENZHOU NOVA NEW ENERGY CO.LTD declares that the radio equipment type SGW08 is in compliance with Directive 2014/53/EU, 2014/30/EU, 2011/65/EU.

The full text of the EU declaration of conformity is available at: https://www.moestech.com/blogs/news/bwy-yc02

11. Recycling Information

All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19/EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, contact the installer or your local authority.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.