SUITU Motorcycle TPMS

Contents

Motorcycle TPMS Tire Pressure Monitoring System User Manual

Model: Motorcycle TPMS

1. Introduction

Thank you for choosing the SUITU Motorcycle Tire Pressure Monitoring System (TPMS). This device is designed to enhance your riding safety by providing real-time monitoring of your motorcycle's tire pressure and temperature. This manual will guide you through the installation, operation, and maintenance of your new TPMS.

Motorcycle TPMS display, handlebar mount, two external sensors labeled 'REAR' and 'FRONT', and a USB charging cable.

Figure 1: SUITU Motorcycle TPMS Components

2. Package Contents

Please check the package contents upon unboxing. If any items are missing or damaged, please contact customer support.

  • 1x TPMS Monitor Display
  • 2x External Sensors (Front & Rear)
  • 1x Handlebar Mounting Bracket
  • 1x USB Charging Cable
  • 2x Anti-theft Nuts
  • 1x Small Wrench (for anti-theft nuts)
Detailed view of all package contents: Receiver, 2 External Sensors, USB Power Cable, Holder, 2 Anti-proof Nuts, and Spanner.

Figure 2: Complete Package Contents

3. Specifications

FeatureSpecification
BrandSUITU
MaterialABS
Monitor Voltage2.1 - 3.5V
Monitor Dimensions (L x W x H)48mm x 48mm x 27mm
Monitor Weight0.2 kg
External Sensor Working Temperature-40°C to 100°C (-40°F to 212°F)
External Sensor Pressure Range0 - 6.5 BAR (0 - 94 PSI)
External Sensor Battery Capacity120mA
External Sensor Working Current16mA
CertificationCE
Waterproof RatingYes

4. Setup

4.1 Monitor Installation

The monitor can be easily installed on your motorcycle's handlebars using the provided bracket.

  1. Attach the mounting bracket to your motorcycle's handlebar. Ensure it is securely fastened and positioned for optimal viewing.
  2. Slide the TPMS monitor onto the bracket until it clicks into place.
  3. Adjust the viewing angle as needed.
Images showing the TPMS monitor mounted on various motorcycle handlebars, demonstrating easy installation.

Figure 3: Monitor Installation Examples

4.2 Sensor Installation

The external sensors are labeled "FRONT" and "REAR" for correct placement. Install them on the corresponding tire valve stems.

  1. Unscrew the original valve cap from your tire.
  2. Screw an anti-theft nut onto the valve stem (clockwise).
  3. Screw the corresponding sensor (FRONT or REAR) onto the valve stem (counter-clockwise) until it is hand-tight.
  4. Using the provided small wrench, tighten the anti-theft nut against the sensor to secure it and prevent tampering.
  5. Repeat for the other tire.

Important: Ensure sensors are tightly secured to prevent air leakage.

5. Operating Instructions

5.1 Display Overview

The monitor display provides comprehensive real-time information about your tires and system status.

Diagram of the TPMS display with labels pointing to: Alarm indicator, Time display, Power display, Pressure unit, Front tyre pressure, Front tyre temperature, Rear tyre pressure, Rear tyre temperature.

Figure 4: TPMS Display Layout

  • Time Display: Shows current time (e.g., PM 12:36).
  • Alarm Indicator: An exclamation mark (!) appears when an alarm condition is met.
  • Power Display: Battery icon indicates the monitor's charge level.
  • Pressure Unit: Displays the current pressure unit (BAR or PSI).
  • Front Tyre Pressure: Real-time pressure for the front tire.
  • Rear Tyre Pressure: Real-time pressure for the rear tire.
  • Front Tyre Temperature: Real-time temperature for the front tire.
  • Rear Tyre Temperature: Real-time temperature for the rear tire.
  • Low Pressure Alarm (LO): Indicates pressure below the set threshold.
  • High Pressure Alarm (HI): Indicates pressure above the set threshold.
  • Sensor Battery Low: An empty battery icon next to the pressure/temperature reading indicates a low sensor battery.
  • Host Battery Low: An empty battery icon in the power display indicates a low monitor battery.

5.2 Power On/Off

To power on or power off the monitor, press and hold either button for 3-6 seconds.

5.3 Automatic On/Off Function

The display will automatically start working when it detects motorcycle movement (vibration) and will power off after a few minutes of no operation or movement. This feature helps conserve battery life.

Diagram showing the TPMS monitor automatically turning on with motorcycle movement and off when stationary, with sound waves indicating an alert.

Figure 5: Automatic Start/Stop Feature

5.4 Setting Parameters

To enter the settings menu, press and hold both buttons simultaneously for a few seconds until the display changes. Use the left button to cycle through settings options and the right button to adjust values. Press and hold both buttons again to save and exit, or wait for the system to time out.

  1. Time Setting: Adjust hours and minutes. You can also select AM/PM or 24-hour format.
  2. Temperature Unit Setting: Switch between Celsius (°C) and Fahrenheit (°F).
  3. Pressure Unit Setting: Switch between BAR and PSI.
  4. Front Wheel Pressure Alarm Value Setting: Set your desired high and low pressure thresholds for the front tire. The default is 2.40 BAR.
  5. Rear Wheel Pressure Alarm Value Setting: Set your desired high and low pressure thresholds for the rear tire. The default is 2.40 BAR.
  6. High Temperature Alarm Value Setting: Set the maximum temperature threshold. The default is 65°C (149°F).

Note: Refer to your motorcycle's manual for recommended tire pressure values.

5.5 Alarm Conditions

The system will alert you with an audible beep and a visual indicator on the display for the following conditions:

  • High Pressure Alarm: Tire pressure exceeds the set high threshold.
  • Low Pressure Alarm: Tire pressure falls below the set low threshold.
  • High Temperature Alarm: Tire temperature exceeds the set high threshold.
  • No Signal Alarm: Display shows "---" for pressure/temperature if a sensor signal is lost.
  • Sensor Failure Alarm: Display shows "LO" for pressure/temperature if a sensor is malfunctioning.
  • Low Sensor Battery: An empty battery icon next to the tire reading.

6. Maintenance

6.1 Charging the Monitor

The TPMS monitor has a built-in rechargeable lithium battery. When the power display shows low battery, connect the monitor to a USB power source using the provided USB charging cable. A full charge typically takes about one hour and can last for several months of normal use.

Image showing the USB charging cable and the magnetic charging port on the back of the TPMS monitor.

Figure 6: USB Charging Port

6.2 Sensor Battery Replacement

The external sensors use CR1632 button cell batteries. When a sensor battery is low, replace it as follows:

  1. Unscrew the sensor from the tire valve stem.
  2. Carefully remove the rubber gasket from the sensor.
  3. Hold the outer casing of the sensor firmly.
  4. Unscrew the core component of the sensor to access the battery compartment.
  5. Remove the old CR1632 battery and insert a new one, ensuring correct polarity.
  6. Reassemble the sensor by screwing the core component back into the casing and replacing the gasket.
  7. Reinstall the sensor on the tire valve stem as described in Section 4.2.

Note: Sensor batteries are pre-installed. Only replace when necessary.

6.3 Cleaning

Wipe the monitor and sensors with a soft, damp cloth. Do not use abrasive cleaners or solvents.

Image showing the TPMS monitor submerged in water, demonstrating its waterproof design.

Figure 7: Waterproof Design

7. Troubleshooting

ProblemPossible CauseSolution
Monitor not turning onLow battery; Not powered onCharge the monitor; Press and hold a button for 3-6 seconds to power on.
Display shows "---" (No Signal)Sensor battery low; Sensor not installed correctly; InterferenceReplace sensor battery; Reinstall sensor securely; Check for strong electromagnetic interference.
Display shows "LO" (Sensor Failure)Sensor malfunctionTry replacing the sensor battery. If issue persists, contact customer support.
Inaccurate readingsSensor not fully tightened; Incorrect sensor placement (Front/Rear)Ensure sensors are tightly secured; Verify correct sensor placement.
Monitor not turning off automaticallyConstant vibration detectedEnsure motorcycle is completely stationary. If issue persists, power off manually.

8. User Tips

  • Initial Setup: While installation is generally easy, take your time with the button presses for settings. The instructions are clear, but practice makes perfect.
  • Battery Life: The monitor's built-in battery offers excellent longevity, often lasting months on a single charge thanks to its auto on/off feature.
  • Versatility: This TPMS is not limited to motorcycles; it has been successfully used on electric scooters as well.
  • Durability: The system is designed to withstand long rides, including off-road conditions, providing reliable performance.
  • Accuracy: The system accurately detects changes in tire pressure and temperature, offering peace of mind during your rides.

9. Frequently Asked Questions (FAQ)

  • Q: Does this device measure outside air temperature?
    A: No, this device measures the temperature of your motorcycle tires, not the ambient outside temperature.
  • Q: Is the tire monitoring system waterproof?
    A: Yes, the monitor and sensors are designed to be waterproof and can withstand various weather conditions.
  • Q: Will the display turn off automatically when the motorcycle is stationary and turn on when moving again?
    A: Yes, the display features an automatic on/off function based on vibration detection to conserve battery life.

10. Warranty and Support

Your SUITU Motorcycle TPMS comes with a standard manufacturer's warranty. For warranty claims, technical support, or any questions not covered in this manual, please contact your retailer or the manufacturer's customer service. Please retain your proof of purchase for warranty purposes.


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.