Haozee MiNi PIR Sensor (ZG-204ZL/ZG-204Z)

Contents

Haozee 2-in-1 Zigbee Mini PIR Motion Detector + Bright Lux Light Sensor

User Manual

Model: MiNi PIR Sensor (ZG-204ZL/ZG-204Z, HZ-PS02)

1. Introduction

Thank you for purchasing the Haozee 2-in-1 Zigbee Mini PIR Motion Detector + Bright Lux Light Sensor. This device combines passive infrared (PIR) motion detection with ambient light sensing (Lux) into a compact, wireless unit. Designed for smart home integration, it operates on the Zigbee 3.0 protocol, offering enhanced security and automation capabilities. Please read this manual carefully before installation and operation to ensure proper use and to avoid any potential damage.

Haozee Mini Zigbee PIR Motion Sensor with Zigbee2mqtt and Home Assistant logos

Figure 1: Haozee Mini Zigbee PIR Motion Sensor

2. Safety Information

WARNING: This product contains a button cell battery.

  • INGESTION HAZARD: This product contains a button cell battery. If swallowed, it can cause severe internal injury or death in just 2 hours. Seek immediate medical attention.
  • Keep the device out of reach of children.
  • Keep the device away from water, damp, or hot environments.
  • Install the device away from strong signal sources such as microwave ovens that may cause abnormal operation.
  • Obstruction by concrete walls or metallic materials may reduce the effective operation range of the device and should be avoided.
  • Do NOT attempt to disassemble, repair, or modify the device.

3. Product Overview

The Haozee Mini PIR Motion Detector is designed for discreet and effective monitoring. Its compact size allows for versatile placement, while its Zigbee connectivity ensures seamless integration into compatible smart home systems.

3.1. Components

Close-up of sensor manual showing Fresnel lens, status indicator, and reset button

Figure 2: Sensor Components

  • Fresnel Lens: Detects infrared radiation changes caused by motion.
  • Status Indicator: LED light indicating device status (e.g., pairing, motion detection).
  • Reset Button: Used for pairing and resetting the device.

3.2. Key Features

  • 2-in-1 Functionality: Combines PIR motion detection and ambient light (Lux) sensing.
  • Zigbee 3.0 Protocol: Ensures broad compatibility with Zigbee hubs and smart home platforms like Home Assistant and Zigbee2MQTT.
  • Super Wide Detection Angle: Hemispherical design provides a detection angle of ≥135°.
  • Effective Detection Distance: Detects motion up to 10 meters in diameter (approx. <5 meters radius).
  • Compact Design: With a maximum diameter of 33mm, it's easy to install discreetly on various surfaces.
  • Low Power Consumption: Powered by a CR2450 button battery, offering approximately one year of standby time.
Diagram showing 135 degree detection angle of the sensor

Figure 3: Super Wide Detection Angle

Images showing the compact sensor on a desk and mounted on a wall

Figure 4: Compact and Easy Installation

Graphic illustrating low power consumption and long battery life

Figure 5: Low Power Consumption

4. Specifications

Attribute Value
Product NamePIR Sensor
Brand NameIHOMECAM (Haozee)
Model NumberMiNi PIR Sensor (ZG-204ZL/ZG-204Z, HZ-PS02)
OriginMainland China
CertificationCE, RoHS
Wireless ProtocolZigbee 3.0
Detection Angle≥135°
Detection DistanceUp to 10 meters in diameter (approx. <5M radius)
Working Voltage3V
Battery TypeCR2450
Standby Current≤12uA
Luminance Meter0~3000lux (for versions with additional luminance sensor)
Operating Temperature-10°C to +40°C
Operating Humidity10%~95%RH
Product SizeØ33mm × 26mm
Product parameter diagram showing dimensions and specifications table

Figure 6: Product Dimensions and Parameters

5. Setup and Installation

5.1. System Requirements

  • WiFi Router
  • Zigbee Gateway/Hub (required for operation)
  • Smartphone (iPhone, iPad iOS 7.0 or higher; Android 4.0 or higher)
  • Compatible Smart Home App (e.g., Smart Life, Tuya Smart, Home Assistant, Zigbee2MQTT)

5.2. Battery Installation

  1. Gently twist the back cover of the sensor counter-clockwise using the provided cover opening tool or a similar flat object.
  2. Insert the CR2450 button battery, ensuring correct polarity. If a battery is already installed, remove the insulation film.
  3. Align the cover and twist clockwise to close securely.
Sensor with cover opening tool and small manual

Figure 7: Sensor and Cover Opening Tool

5.3. Mounting the Sensor

  1. Choose a Location: Select an area where motion detection is desired. For optimal performance, install the product where persons may be detected.
  2. Recommended Height: Install the sensor approximately 2-3.5 meters (6.5-11.5 feet) above the ground. If there are pets or other small animals in the detection area, consider installing the sensor at a height of 1-2 meters (3.3-6.5 feet) to minimize false triggers.
  3. Avoid Obstructions: Ensure there are no large obstacles directly in front of the sensor's lens that could block its field of view.
  4. Environmental Considerations: Avoid installing near objects that cause rapid temperature changes (e.g., air conditioners, fans, refrigerators, ovens) or in direct sunlight, as this can affect detection accuracy.
  5. Attachment: Remove the protective film from the adhesive on the base of the sensor. Firmly press the device onto a clean, flat surface (desk, wall, etc.).

5.4. Network Configuration (Pairing with Zigbee Gateway)

This product requires a Zigbee gateway/hub to function and connect to your smart home system.

  1. Power On: Ensure the battery is correctly installed and the device is powered on.
  2. Enter Pairing Mode: Press and hold the reset button on the sensor for approximately 3 seconds. The red LED indicator will flash rapidly, indicating the device is in pairing mode.
  3. Open App: On your smartphone, open your Zigbee gateway's control app (e.g., Smart Life, Tuya Smart, Home Assistant interface).
  4. Add Device: Navigate to the device management section and select "Add sub-device" or "Add sensor."
  5. Complete Pairing: Follow the on-screen instructions in the app. The connection process may take 10-120 seconds. Once successfully paired, the LED indicator will stop flashing, and the device will appear in your app.
Scanned manual page showing app registration and device adding steps

Figure 8: App Pairing Process

Scanned manual page with network configuration and installation instructions

Figure 9: Detailed Network Configuration and Installation

6. Operation

6.1. Motion Detection

Once paired, the sensor will detect motion within its field of view. When motion is detected, the sensor will send a signal to your Zigbee gateway, triggering any configured automations or alerts in your smart home system.

6.2. Lux Light Sensing (if applicable)

For models equipped with a Lux sensor, the device can measure ambient light levels. By default, the Lux value is typically uploaded only when motion is detected. To enable real-time Lux detection or adjust the Lux sensing interval, you may need to configure settings within your smart home app.

Note: Lux measurement can only be measured during a change in state of motion.

6.3. LED Indicator Control

You can typically control the LED indicator light through your smart home app. A single flash usually indicates the LED is turned ON, while three flashes indicate it's turned OFF.

6.4. Motion Hold Time

The default motion hold time (the duration the sensor reports motion after detection) is typically 10 seconds. This setting can often be adjusted within your smart home app to suit your automation needs.

7. Maintenance

7.1. Battery Replacement

When the battery level is low, your smart home app should notify you. To replace the CR2450 battery, follow the steps outlined in Section 5.2 (Battery Installation).

7.2. Cleaning

To clean the sensor, gently wipe the exterior with a soft, dry cloth. Do not use liquid cleaners or abrasive materials, as these can damage the device.

7.3. Firmware Updates

Periodically check your Zigbee gateway's app for any available firmware updates for the sensor. Keeping the firmware updated ensures optimal performance and security.

8. Troubleshooting

8.1. Common Issues and Solutions

Problem Possible Cause / Solution
Device not pairing/connecting to gateway.
  • Ensure the battery is correctly installed and has power.
  • Verify the sensor is within range of your Zigbee gateway.
  • Reset the sensor (long press reset button for 3 seconds) and try pairing again.
  • Check your Zigbee gateway's app for any error messages or specific pairing instructions.
Inaccurate or inconsistent motion detection.
  • Check installation height and angle. Adjust if necessary (refer to Section 5.3).
  • Ensure no obstacles are blocking the sensor's view.
  • Relocate away from heat sources (AC, fans, direct sunlight) that can cause false triggers.
  • Adjust sensitivity settings in your smart home app if available.
Reduced wireless range or connectivity issues.
  • Avoid placing the sensor behind concrete walls or large metallic objects.
  • Ensure the Zigbee gateway is centrally located or use Zigbee repeaters to extend network coverage.
  • Keep away from strong signal interference sources (e.g., microwave ovens, Wi-Fi routers on conflicting channels).
Lux sensor not reporting or inaccurate readings.
  • Ensure you have the 'With Lux' version of the sensor.
  • Remember that Lux is often only measured during a change in motion state.
  • Check app settings for Lux reporting frequency or real-time options.

8.2. Frequently Asked Questions (FAQ)

Q: What does 'Lux' mean?
A: Lux is a unit of illuminance, measuring the intensity of light as perceived by the human eye. In this sensor, it measures the ambient light level.
Q: Does this sensor work with SmartThings?
A: Yes, many users report successful integration with SmartThings, as it uses the standard Zigbee protocol.
Q: Can this item work without an internet connection?
A: The sensor itself communicates via Zigbee to a local gateway. While local automations might function without internet, full smart home integration, app control, and remote access typically require an active internet connection for your Zigbee hub.
Q: Is it compatible with Sonoff Zigbee 3.0 hub and Home Assistant?
A: While some product information may suggest limited compatibility with certain hubs, user reviews widely confirm excellent functionality with Home Assistant and Zigbee2MQTT. Compatibility with specific Sonoff hubs may vary, but general Zigbee 3.0 support is expected.

9. User Tips

  • These sensors are praised for their small size and aesthetic appeal, making them easy to integrate discreetly into any room.
  • The CR2450 coin batteries are noted for their long lifespan, contributing to low maintenance.
  • Users frequently report excellent and quick performance with Home Assistant and Zigbee2MQTT integrations.
  • The sensor offers a short cooldown time and adjustable sensitivity levels, which can be configured in Home Assistant for precise automation.
  • The integrated Lux sensor is particularly useful for creating automations in dimly lit areas, such as hallways, to control lighting based on ambient light conditions.
  • Consider these sensors as a cost-effective alternative to more expensive branded options, offering comparable functionality and reliability.

10. Warranty and Support

This product comes with a standard manufacturer's warranty against defects in materials and workmanship. Please refer to your purchase documentation for specific warranty terms and duration.

For further assistance or detailed guides, you may refer to the official user manual PDF: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.