Quansheng UV-5R PLUS

Contents

Quansheng UV 5R Plus Walkie Talkie User Manual

Model: UV-5R PLUS

Brand: Quansheng

1. Introduction

This manual provides detailed instructions for the safe and efficient operation of your Quansheng UV 5R Plus Walkie Talkie. Please read this manual thoroughly before using the device to ensure proper functionality and to understand all features.

Quansheng UV-5R Plus Walkie Talkie with frequency ranges and key features

Image: Quansheng UV-5R Plus Walkie Talkie displaying its frequency ranges and key features.

2. Safety Precautions and Warnings

2.1 FCC FRS/GMRS/Amateur WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. Do not use this device when the antenna shows obvious damages. Hold this transmitter approximately 25 mm away from your face and speak normal with the antenna pointed up and away. Use the supplied belt clip for body-worn configuration as other accessories may not comply to the limits.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

2.2 CE WARNING

Use the two-way radio in an environment with temperatures between 0-40°C; otherwise, it may damage the radio. It can be operated under 2000m. The radio equipment type two-way radio is in compliance with Directive 2014/53/EU.

2.3 General Precautions Before Using

  • Keep the radio and accessories out of reach of children.
  • Maintenance should only be performed by professional technicians.
  • Use only the standard battery pack and charger to prevent damage to the radio.
  • Use the standard antenna to ensure optimal communication distance.
  • Do not expose the radio to direct sunlight for extended periods or near heat sources.
  • Avoid extreme dust or wet environments.
  • Do not clean the radio with harsh chemical products, cleaning agents, or strong washing agents.
  • Do not transmit when the antenna is not installed.
  • If you detect a bad smell or smoke, immediately turn off the radio, remove the battery, and contact an agent.

3. Package Contents

Carefully unpack the portable radio and check for the following items before discarding packaging materials:

Item Quantity
Portable Radio1
Antenna1
Li-ion Battery1
Battery Charger1
Belt Clip1
User's Manual1
Image showing the package contents of the Quansheng UV-5R Plus

Image: Contents included in the Quansheng UV-5R Plus package.

4. Radio Overview

4.1 Radio Diagram

Detailed diagram of the Quansheng UV-5R Plus radio, labeling its components

Image: Labeled diagram of the Quansheng UV-5R Plus showing its various components.

4.2 Indicator Details

  • Red Light: Transmitting
  • Green Light: Receiving
  • Blue Light: On when Charging / Off when the radio is fully charged

4.3 Power/Volume Switch

  • Turn on the radio by turning clockwise.
  • Turn off the radio by turning counter-clockwise.

5. Charging the Battery

5.1 Charging Notes

  • Battery packs are not charged when shipped. Charge them before use.
  • Initial charging after purchase or extended storage (longer than 2 months) may not bring the battery pack to its greatest capacity. Full capacity is achieved after repeated charging and discharging two or three times.
  • Before charging, power off the radio. Do not use the radio during charging, as it may affect normal charging and cause dangerous accidents.
  • After the battery pack is fully charged, remove it from the charger-base. Do not charge it again before it is completely run out, as this may destroy the memory effect of the battery.
  • If, despite correct charging methods, the battery does not gain capacity or usage time, it indicates the battery life is nearing its end. Please change to a new battery pack.
  • Always use the original factory battery pack and charger. These are available from your local agent.
  • Do not use non-original factory battery packs or accessories, as they may cause dangerous accidents.

5.2 Important Notes

  • Use the original factory charger for charging.
  • To protect the environment, please recycle the battery pack.
  • Never attempt to remove the casing from the battery pack.

6. Initial Setup

6.1 Power On Password Protection

Turn the "Power/Volume Switch" clockwise to power on the radio. If a Power On Password Protection is set in the program, the screen will display "LOCK". You must input the password first for normal operation.

7. Operating Instructions

7.1 LCD Display Symbols

The LCD displays various symbols to indicate the radio's status:

Symbol Description
YllSignal Strength. The smaller the number of grids, the weaker the signal.
HMLTransmitting Output Power Indicator (High, Medium, Low).
CT DCSCTCSS or DCS code is active.
DVoice prompt is on.
NRadio operates in narrow band mode.
VOXVOX Function is active (Voice Operated Transmit).
+-Transmitting frequency equals receiving frequency plus/minus a deviation.
DTMFDTMF signal decoding is on.
DWFrequency dual watch is on.
Keypad locking.
Battery status indicator. Shows when battery is low.
SCRVoice encryption is on.
RReverse mode (receive and transmit frequency reverse).
◆◆Scanning. Participating in scan list 1 or 2.
WXCross-Band Receiving/Transmitting.
RXReceiving.
TXTransmitting.
ㅂPC programming data cable connection.
AMAM receiving mark.
NSNOAA channel automatic scan.
Close-up of the Quansheng UV-5R Plus LCD display, highlighting its clarity and intuitive operation

Image: The large LCD display of the UV-5R Plus, showing clear and intuitive information.

7.2 Key Functions

PTT Key (Transmitting Key)

  • Press PTT to transmit and speak into the microphone.
  • Release PTT to receive.

Programmable Function Key and Its Function

Initial Function:

  • Side Key 1: Short press for Monitor function. Long press for 1750Hz.
  • Side Key 2: Short press for Jacklight. Long press for emergency alarm.

Functions settable by program software:

  • Emergency Mode On/Off: Activates emergency alarm.
  • High/Low Output Power Selection: Switches between High/Low output power.
  • Monitor: Turns Monitor function on/off. Ignores CTCSS/DCS to listen to actual channel noise.
  • FM Radio: Turns FM Radio Mode on/off.
  • Scan On/Off: Turns Scan function on/off.
  • VOX On/Off: Turns VOX function on/off.
  • Transmitting 1750: Turns 1750 continuous transmitting on.
  • Jacklight: Turns Jacklight on/off.

Keypad Key

  • MENU/Confirm Key: Short press to enter menu, select item, and press again to confirm. Long press to enter the last setting item. Under DTMF, it means 'A' code word.
  • Up Key: Moves upward in menus. Under DTMF, it means 'B' code word.
  • Down Key: Moves downward in menus. Under DTMF, it means 'C' code word.
  • * Key: Short press to enter manual dial and call page. Long press to start frequency or channel scanning. Under DTMF, it means '*' code word.
  • EXIT/Clear Key: Short press to exit current menu. Long press to return to main page. In input status, clears input info. Under DTMF, it means 'D' code word.
  • F Key: Works with 0-9 for quick function switching. Long press to lock/unlock keyboard. Under DTMF, it represents '#' code word.

7.3 Menu Information

Press the MENU key to enter Menu Selection. Use Up/Down keys to select the Menu No., and press MENU key to confirm the selection. Press EXIT key to return to the Upper Menu. Long press EXIT key to return to the main page.

Item Name No. Function Description Value Range
SQL1Squelch Level0-9
STEP2Step Frequency (2.5K/5K/6.25K/10K/12.5K/25K)0-5
TXP3Output Power (LOW/MID/HIGH)0-2
R_DCS4Receive DCS (OFF, 1-104:DCS, 105-208: reverse DCS). Short Press F+* to trigger DCS to scanning.0-208
R_CTCS5Receive CTCSS (OFF, 1-50: CTCSS). Short Press F+* to trigger CTCSS scanning.0-50
T_DCS6Transmit DCS (OFF, 1-104: DCS, 105-208: reverse DCS)0-208
T_CTCS7Transmit CTCSS (OFF, 1-50: CTCSS)0-50
SFT-D8Frequency Deviation Setting (OFF:TX frequency =RX frequency; ADD: TX frequency=RX frequency + frequency deviation; SUB: TX frequency=RX frequency-frequency deviation)0-2
OFFSET9Frequency of Frequency Deviation (0-999.9999M)
W/N10Channel Bandwidth (0:WIDE, 1:NARROW)0-1
SCR11Encrypted Communication (OFF, 1-10: 1 to 10 types of scrambling frequency.)0-10
BCL12Busy Channel Lock (OFF,ON)0-1
MEM-CH13Channel Save (Choose the channel by Up/Down Key and Number Key, press MENU key to Save the channel.)
SAVE14Battery Save (OFF/1:1/1:2/1:3/1:4) The rate between active time and sleep time.0-4
VOX15VOX Setting (OFF: turn off VOX, 1-10: 1 to 10 grade.)0-10
ABR16Auto Backlight (OFF: turn off Backlight, 1-5: turn off Backlight in 1-5 seconds)0-5
TDR17Dual-watch On/Off (OFF: Close, CHAN A: Default TX Channel is A channel, CHAN B: Default TX Channel is B channel.)0-2
WX18Cross-Band Receiving/Transmitting (OFF: Close, CHAN A: TX Channel is A channel, CHAN B: TX Channel is B channel.)0-2
BEEP19BEEP Control (OFF, ON)0-1
TOT20Time-Out-Timer (1-10min)1-10
VOICE21Voice Prompt (OFF, CHI: Chinese, ENG: English)0-2
SC-REV22Scan Resume Mode (TO: Resume scan after 5 seconds pause; CO: Resume scan after signal disappear; SE: After receive the signal, stop scan.)0-2
MDF23Channel Display Mode (FREQ: Display frequency, CH: Display channel No., NAME: Display channel name)0-2
AUTOLK24Auto Keypad Lock (OFF,ON)0-1
S-ADD125Whether to participate in list 1 scanning (OFF: not participating, ON: participation)0-1
S-ADD226Whether to participate in list 2 scanning (OFF: not participating, ON: participation)0-1
STE27Tail Tone Elimination (OFF,ON)0-1
RP-STE28Repeater Tail Tone Elimination (OFF,ON)0-1
MIC29MIC Sensitivity (0-4: 0-4 level)0-4
1-CALL30One Key Call Channel (Select the channel through the Up/Down keys and the Number keys)
S-LIST31Channel Scan List Select (LIST1:Scan list 1, LIST2:Scan list 2)1-2
SLIST132Channel Scan List 1 Configuration
SLIST233Channel Scan List 2 Configuration
AL-MOD34Alarm Mode (SITE: local alarm; TONE: Distant + local alarm)0-1
AN-ID35ANI-ID, DTMF communication radio ID
UPCODE36DTMF UP CODE
DWCODE37DTMF DOWN CODE
D-ST38DTMF Side Tone Switch (OFF, ON)0-1
D-RSP39DTMF Decoding Response (NULL: Close, Ring: Local ringing, REPLY: reply response, both: local ringing +reply response)0-3
D-HOLD40DTMF Auto Reset Time (5s-60s)5-60
D-PRE41DTMF pre-load time (30-990ms)3-99
PTT-ID42DTMF PTT-ID TX Mode (OFF: Close, BOT: Press PTT to send UP CODE, EOT: Release PTT to send DOWN CODE, BOTH: Press or release PTT to send.)0-3
D-DCD43DTMF decoding enable signal (OFF,ON)0-1
D-LIST44DTMF Contact List (Choose the contact by Up/Down Key and Number Key, press MENU key to select the contact and call directly.)1-16
PONMSG45Displays of Power On (FULL: full screen display, MSG: Welcome info, VOL: Voltage. It can modify it by program software.)0-2
ROGER46Reminding of End Talk (OFF: no reminding, ROGER: with reminding, MDC: Frog Sound Tail Tone)0-2
VOL47Battery Voltage0-1
AM48AM Channel Mode On/Off (Used only for 108-136MHz)0-1
NOAA_S49NOAA Channel Auto Scan On/Off
DEL_CH50Channel Delete (Choose the channel by Up/Down Key and Number Key, press MENU key to delete the channel.)
RESET51Reset (VFO: Reset parameter beside channel parameter; ALL: Reset all parameter.)0-1

7.4 Common Operations

7.4.1 Switch Main Channel

  • Press F+2 Key to switch main channel.
  • The solid arrow indicates the main channel.
  • Press PTT to start TX in the main channel.

7.4.2 Dual Band Single-Watch/Dual-Watch Switch

Dual-watch operation mode can be set via Menu 17 (TDR). Select CHAN_A for Default TX Channel A, or CHAN_B for Default TX Channel B. The screen will show "DW".

7.4.3 Frequency/Channel Mode Switch

  • In the main page, press F+3 key to switch between Frequency Mode and Channel Mode.
  • Frequency Mode: Manually input RX frequency or use Up/Down keys to adjust. TX frequency can be set via Frequency or Direction of Offset Frequency.
  • Channel Mode: Displays actual channel number. Manually input channel number or use Up/Down keys to switch channels.

7.4.4 Cross-Band Receiving/Transmitting

Set via Menu 18 (WX). Press MENU to enter settings. OFF: Main Channel TX. CHAN_A or B: Default TX Channel A or B, displaying "DW" character.

7.4.5 Channel Save

  • In MR Mode, Channel Save is available. You can copy the current channel to a new channel.
  • In VFO Mode, set RX Frequency, Frequency Deviation Direction, Wide/Narrow Bandwidth, RX/TX CTCSS/DCS, TX Output Power, Scanning participation, DTMF code, Scrambler, etc. Then press MENU → 13 → CH-001, press MENU again to enter Channel Save. Choose channel by Up/Down Key or Number Key. Press MENU again, LCD shows "SURE?". Press MENU to save.
  • If a saved channel shows CH-XXX, it is saved. If it shows XXX, the channel is empty.

7.4.6 Channel Delete

Press MENU → 50 → CH-XXX, then press MENU again to enter Channel Delete. Choose the channel to delete by Up/Down Key or Keypad. Press MENU again, LCD shows "SURE?". Press MENU to delete the channel.

7.4.7 Receiving/Transmitting CTCSS/DCS Setting

Process Flow:

  • MENU → 4 R-DCS: Choose RX DCS Code.
  • MENU → 5 R-CTCS: Choose RX CTCSS Code.
  • MENU → 6 T-DCS: Choose TX DCS Code.
  • MENU → 7 T-CTCS: Choose TX CTCSS Code.

CTCSS/DCS removes unwanted noise signals during reception.

7.4.8 Fast Copy One Channel (Frequency Meter)

Diagram illustrating the 'Fast Copy One Channel' feature

Image: Illustration of the Fast Copy One Channel feature, allowing the radio to act as a frequency meter.

  • Fast Copy requires a strong signal. Both transmitter and receiver must have antennas installed and be within reasonable distance.
  • Press F+4 to enter Frequency Meter interface. When a strong signal is received, the LCD displays signal carrier frequency and transmitting channel (CTCSS or DCS). Press '*' key to re-measure.
  • After measuring, press MENU to save the frequency and CTCSS/DCS to a specified channel.
  • During measuring, press EXIT or PTT to exit Frequency meter.
  • Set correct receiving frequency, then press F+* to start searching. When a valid CTCSS/DCS signal is received, it displays the searched TX CTCSS/DCS signal. Press MENU to save.
  • If the screen displays SCAN CMP, a valid signal was found. If SCAN FAIL, no valid signal was found.

7.4.10 DTMF Calling

  • Manual dialing: Press PTT and keypad number keys.
  • Automatic calling: Press *, enter 3 digits, short press PTT. Sends its own ID number.
  • Single call: Send other party's ID + your ID code (e.g., 123*100 for ID 100 to call ID 123).
  • Group call: Use a group calling code (set by program software). E.g., send 12# to call radios with ID 120-129.
  • All call: Send ### to call all users.

7.4.11 DTMF Receiving

Process Flow: Press MENU → 43 DCD ON. When a DTMF personal ID code is received, decoding is successful, and communication can occur within the reset time. To re-decode, you may need to reset. MENU → 40 D-HOLD 5S sets the automatic reset time (default 5 seconds). MENU → 39 D-RSP sets the automatic response (NULL: off, RING: local ring, REPLY: automatic callback, BOTH: local ring + automatic callback).

7.4.12 PTTID

Configure DTMF online and offline codes via program software. When enabled, the radio sends the online code when PTT is pressed and the offline code when PTT is released.

7.4.13 Scanning

  • Start Scanning: Long press *Key or set Side Key as Scanning Start/Close Switch.
  • Frequency Scanning: Change scan direction with Up/Down key. Exit with PTT or Exit key.
  • Channel Scanning: Detects channels in the scan list. Answer incoming calls with PTT Key.
  • Priority Scanning: Specify priority channels. Scanning focuses 50% on priority 1 members.

7.4.14 Emergency Alarm

Image demonstrating the 'Frog Sound Ending Tone' feature

Image: The radio emitting a 'Frog Sound' tail tone, a feature that can be used in various signaling contexts, including emergency alerts.

  • Used for emergency situations. Can be initiated anytime, even during activity on the current channel. Configure the emergency alarm button via programming software.
  • Press the emergency alarm key to start local audible alarm and send remote alarm.
  • Exit alarm mode by any key.
  • Process: MENU → 34 → AL-MOD TONE (alarm sound and remote signal).
  • Process: MENU → 34 → AL-MOD SITE (local alarm sound only).

7.4.15 FM Radio

  • Press F+0 to enter FM radio mode. Use Up/Down keys or keypad to change frequency/channels.
  • Press F+1 to switch between VFO and MR mode.
  • Press F+2 for automatic FM channel search (stores up to 20 channels).
  • Press F+3 for manual FM channel search (manually store channels).
  • Menu key stores FM channel; Exit key exits search; Up/Down keys switch scanning direction.
  • In FM Mode, if a call is received or PTT is pressed, it temporarily exits FM Mode for communication, then returns.
  • Press EXIT Key or F+0 Key to exit FM Mode.

7.4.16 Emergency Weather Channel Receiving (NOAA)

  • Press F+5 to enter or exit NOAA Weather Alert.
  • This radio can receive 10 NOAA channels.
  • This mode can be set through Menu 49 NOAA_S.

7.4.17 Keypad Locking

  • Long press the # key to lock or unlock all keypad keys. Side keys remain functional.

7.4.18 Reset

  • Process: Press MENU → 51 → RESET.
  • VFO: Resets all storage channels.
  • ALL: Resets all parameters, including storage channels. LCD displays "Sure?". Press MENU, radio restarts, and all menu settings return to factory defaults.

7.4.19 One Key Call Channel

F+9 immediately jumps to a one-key call channel. You can set an important channel to one-key call via MENU 30 → 1-call.

7.4.20 Aviation Band Receiving

  • Enter the receiving frequency. If the local aviation frequency is unclear, the scanning function can scan the 108-136 full frequency band.
  • MENU 48 → AM ON sets channel modulation to AM for aviation intercom.
  • MENU 48 → AM OFF sets channel modulation to FM.
  • Menu 48 settings are only valid for the 108-136 frequency band.

7.4.21 Wireless Radio Replication

  • Hold PTT + side key 2 to enter Wireless Radio Replication interface. LCD displays Air Copy (RDY).
  • Both transmitting and receiving radios can use the digital keyboard to set the frequency. Frequencies must be consistent. Default is 410.0125MHz.
  • Press EXIT key on the receiving radio to enter receiving mode (Air Copy displayed).
  • Press MENU key on the transmitting radio to start frequency data transmission (Air Copy displayed).
  • During copy, LCD displays RCV:XX E:XX (errors). When finished, transmitter displays SND: 120.

8. Specifications

8.1 General Specifications

Feature Specification
Channel200
Stored FM Radio Channel Quantity20
NOAA Channel10
Frequency Stability±1ppm
Modulation ModeFM: 11KΦF3E (12.5KHz), 16KΦF3E (25KHz)
Dimensions115mm x 60mm x 37.5mm
Weight234g
Operating Temperature-20°C to +60°C
Antenna Impedance50Ω

8.2 Receiving Specifications

Band Sensitivity (FM: 12dB SINAD)
F1 (50-76MHz)-121dBm
F2 (108-135.9975MHz)-121dBm
F3 (136-173.9975MHz)-123dBm
F4 (174-349.9975MHz)-123dBm
F5 (350-399.9975MHz)-123dBm
F6 (400-469.9975MHz)-123dBm
F7 (470-599.9975MHz)-121dBm
WFM (76-108MHz)-110dBm (20dB SINAD)
AM (108-135.9975MHz)-113dBm (10dB S/N)
Audio Frequency≥0.5W
Audio Distortion≤10%

8.3 Transmitting Specifications

Feature FCC Version CE Version NORMAL Version
FrequencyUHF 420-450MHz, VHF 144-148MHzUHF 430-440MHz, VHF 144-146MHzUHF 400-470MHz, VHF 136-174MHz, UHF 350-400MHz
Output Power≤5W≤5W≤5W
Emission Current≤1.5A≤1.5A≤1.5A
Max Frequency Deviation≤5KHz (25KHz), ≤2.5KHz (12.5KHz)≤5KHz (25KHz), ≤2.5KHz (12.5KHz)≤5KHz (25KHz), ≤2.5KHz (12.5KHz)
Modulation Distortion≤5%≤5%≤5%
Stray Power≤7.5uW≤7.5uW≤7.5uW
Adjacent Channel Power70dB (25KHz), 60dB (12.5KHz)70dB (25KHz), 60dB (12.5KHz)70dB (25KHz), 60dB (12.5KHz)
Residual Modulation40dB40dB40dB

All stated specifications are subject to change without notice or obligation.

9. Troubleshooting

If you encounter issues with your Quansheng UV 5R Plus, consider the following common problems and solutions:

  • No Power: Ensure the battery is fully charged and correctly inserted. Check the power/volume switch.
  • No Reception/Transmission: Verify the antenna is securely attached. Check frequency and channel settings. Ensure you are within range. Confirm CTCSS/DCS settings match the other party.
  • Distorted Audio: Check the squelch level (SQL setting). Ensure the antenna is not damaged. If on airband, some users report distortion; ensure proper frequency and modulation settings.
  • Keypad Unresponsive: Check if keypad lock is active (long press # key to toggle).
  • Charging Issues: Ensure you are using the original charger. If the battery does not hold a charge after repeated cycles, it may need replacement.
  • Radio Not Functioning as Expected: Consider performing a factory reset (MENU → 51 → RESET, select ALL). Note that this will erase all custom settings.

10. User Tips

  • Firmware Updates: Many users find enhanced functionality by updating the radio's firmware, such as to Egzumer.Vo.22. This often requires a PC cable and specific software.
  • Airband Reception: The radio is capable of receiving airband signals. If experiencing distortion, ensure correct frequency and modulation settings.
  • Battery Life: The large battery capacity (2200mAh) allows for extended use. Follow proper charging procedures to maximize battery lifespan.
  • USB-C Charging: While some versions may support USB-C charging, verify your specific model. If not included, a separate charger is required.
  • Local Regulations: Be aware that importing and using radio equipment may be subject to local customs and telecommunication regulations in your country. Ensure compliance to avoid issues.

11. Warranty and Support

This radio incorporates excellent design and advanced technology. For detailed warranty information and support, please refer to the official user manual PDF or contact your local dealer.

For the complete user manual in PDF format, please refer to the following document: Quansheng UV 5R Plus User Manual (PDF).


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.